Adj Fog Fury 3000 Manual

Adj Effekt maskine Fog Fury 3000

Læs gratis den danske manual til Adj Fog Fury 3000 (5 sider) i kategorien Effekt maskine. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Adj Fog Fury 3000, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

User Instructions

Rev. 9/20

Caution: Fog Machines may set o Smoke Alarms!

specications, diagrams, images, and instructions herein are

subject to change without notice. ADJ Products, LLC logo and

identifying product names and numbers herein are trademarks

of ADJ Products, LLC. Copyright protection claimed includes all

forms and matters of copyrightable materials and information

now allowed by statutory or judicial law or hereinafter granted.

Product names used in this document may be trademarks or

registered trademarks of their respective companies and are

hereby acknowledged. All non-ADJ Products, LLC brands and

product names are trademarks or registered trademarks of their

respective companies.

ADJ Products, LLC and all aliated companies hereby dis-

claim any and all liabilities for property, equipment, building, and

electrical damages, injuries to any persons, and direct or indi-

rect economic loss associated with the use or reliance of any

information contained within this document, and/or as a result

of the improper, unsafe, unsucient and negligent assembly,

installation, rigging, and operation of this product.

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment.

Please turn o all electrical products when they are not in use. To

avoid power consumption in idle mode, disconnect all electrical

equipment from power when not in use. Thank you!

This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities

or lack of experience and knowledge. Unless they have

been given supervision or instruction concerning the use of

the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not

play with the appliance.

FOG FURY 3000

5011471

ADJ Products, LLC - www.adj.com - Fog Fury 3000 Instruction Manual Page 4 ADJ Products, LLC - www.adj.com - Fog Fury 3000 Instruction Manual Page 5

Power Supply: Before plugging your unit in, be sure the source volt-

age in your area matches the required voltage for your ADJ Fog Fury

3000. The ADJ Fog Fury 3000 is available in a 120v and 230v version.

Because line voltage may vary from venue to venue, you should be

sure your unit voltage matches the wall outlet voltage before attempt-

ing to operate you xture.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used as a form of communication between intelligent fixtures

and controllers. A DMX controller sends DMX data instructions from

the controller to the fixture. DMX data is sent as serial data that trav-

els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter-

minals located on all DMX fixtures (most controllers only have a DATA

“OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of

dierent manufactures to be linked together and operate from a single

controller, as long as all xtures and the controller are DMX compli-

ant. To ensure proper DMX data transmission, when using several

DMX fixtures try to use the shortest cable path possible. The order

in which fixtures are connected in a DMX line does not influence the

DMX addressing. For example; a fixture assigned a DMX address of 1

may be placed anywhere in a DMX line, at the beginning, at the end,

or anywhere in the middle. When a fixture is assigned a DMX address

of 1, the DMX controller knows to send DATA assigned to address 1

to that unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation):

The Fog Fury 3000 can be controlled via DMX-512 protocol. The Fog Fury

3000 has 3 DMX channels. The DMX address is set on the back panel.

Your unit and your DMX controller require a standard 3-pin XLR connec-

tor for data input and data output (Figure 1). We rec-

ommend Accu-Cable DMX cables. If you are making

your own cables, be sure to use standard 110-120

Ohm shielded cable (This cable may be purchased

at almost all pro lighting stores). Your cables should

be made with a male and female XLR connector on

either end of the cable. Also remember that DMX

cable must be daisy chained and cannot be split. Figure 1

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

DMX +

DMX -

COMMON

DMX512 OT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket

XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

Termination educes signalr errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX

xtures may be implemented in a 3-pin DMX line. When inserting stan-

dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,

these adaptors are readily available at most electric stores. The chart

below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Fog Fury 3000 DMX Information Fog Fury 3000 DMX Information

Produkt Specifikationer

Mærke:	Adj
Kategori:	Effekt maskine
Model:	Fog Fury 3000

Har du brug for hjælp?

Hvis du har brug for hjælp til Adj Fog Fury 3000 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Effekt maskine Adj Manualer

Adj Kaos Manual

28 Januar 2025

Adj Inno Pocket Beam Q4 Manual

28 Januar 2025

Adj Inno Pocket Spot Manual

28 Januar 2025

Adj Inno Spot Pro Manual

28 Januar 2025

Adj Flat Par QWH5XS Manual

14 September 2024

Adj ELEMENT QA Manual

5 September 2024

Adj 18P Hex Manual

3 September 2024

Adj Mini Spot LED Manual

30 August 2024

Adj Encore Burst RGBW IP Manual

30 August 2024

Adj VF1600 Manual

24 August 2024

Effekt maskine Manualer

Nyeste Effekt maskine Manualer

Blizzard Lighting Colorise Quadra Manual

2 April 2025

Blizzard Lighting Hypno Spot Manual

2 April 2025

Blizzard Lighting Blok 2 IP Manual

2 April 2025

Blizzard Lighting Blok 1 IP Manual

2 April 2025

Blizzard Lighting Stiletto I7 Manual

2 April 2025

Blizzard Lighting PixelStorm 240 Manual

2 April 2025

Midas Legend L1B Manual

1 April 2025

Blizzard Lighting HotBox Infiniwhite Manual

31 Marts 2025

Blizzard Lighting RokBox EXA Manual

31 Marts 2025

Blizzard Lighting Verismo Fresnel WW Manual

27 Marts 2025