AMX DX-TX-DWP Manual

AMX Ikke kategoriseret DX-TX-DWP

Læs gratis den danske manual til AMX DX-TX-DWP (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 81 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 41 anmeldelser. Har du et spørgsmål om AMX DX-TX-DWP, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

QUICK START GUIDE

DXLink™ Multi-Format Wallplate Transmitter and

DXLink™ Multi-Format Decor Style Wallplate Transmitter (US)

Overview

The DXLink Multi-Format Wallplate TX and DXLink Multi-Format Decor Style Wallplate TX

are used in conjunction with switchers that support DXLink Technology for transmission

of HDMI or analog video over twisted pair cable. Both TXs are compatible with the

DXLink HDMI RX and support InstaGate Pro® Technology. The Hardware Reference

Manual – DXLink Twisted Pair Transmitters /Receiver contains complete documentation

(including full specifications and supported input and output resolutions); for details,

see

www.amx.com.

Installation

System Setup

These Transmitters receive an HDMI signal (or DVI via a cable adapter) or an analog

video signal plus an audio signal from the source device. The audio can be either digital

audio embedded with the HDMI signal or analog stereo audio. Both the video and audio

are transmitted over twisted pair cable to a DXLink Input Board in a switcher that

supports DXLink Technology (see the example in FIG. 2). From the Input Board, the

signal can be routed through an output board. If the output board is a DXLink Output

Board, a DXLink HDMI RX is required between the board and the destination.

DIP Switch #3 Toggle

Before mounting the Transmitter – If a network connection is required, DIP switch #3

Toggle must be set to ON. #3 Toggle is shipped in the OFF position. When flipped ON

(up), the Transmitter will attempt a DHCP connection. Flipping the #3 Toggle ON is the

only way to access the Wallplate TX and Decor TX in NetLinx Studio. For both types of

Transmitters, #1, #2, and #4 Toggles are non-functional (must remain OFF). For

Auto-setup with an Enova DGX 100 Series Switcher, set #3 Toggle to OFF and see the

switcher’s manual.

IP Addressing Modes

DHCP Mode (enabled when #3 Toggle is flipped ON)

In DHCP Mode, the Transmitter attempts to get a DHCP lease (consisting of an IP

address, gateway, and other network parameters). If the attempt fails, the Transmitter

configures itself for a link-local address, but periodically re-tries DHCP and re-assigns

the IP to a valid DHCP grant if successful. At any time, if the Transmitter determines

that its IP address has changed, it will disconnect and reconnect to the Master.

Static IP Mode (set with ID button or Telnet command)

With #3 Toggle set to ON, press ID for 10 seconds to assign an address of 192.168.1.2

or use a Telnet command to set unit to Static IP Mode (see the Hardware Reference

Manual).

Mounting the Wallplate TX and Decor Wallplate TX

Wallplate TX – The holes in the Wallplate TX mounting bracket are designed to

accommodate a variety of gang boxes using 2 or 4 screws (standard and metric are

provided). Be sure to orient mounting bracket as shown in FIG. 4.

Decor Wallplate TX – The Decor Wallplate TX mounts into a standard US double-gang

back box. Decor style front cover plate is customer provided.

Technical Ground

If the system is experiencing problems with delivery of DXLink signals to/from an Enova

DGX Digital Media Switcher or Enova DVX Solution, adding a ground wire from the TX/

RX to the switcher may improve performance (see FIG. 7 on the next page). Technically

this type of grounding is only required when a DXLink Transmitter or Receiver is

connected to an ungrounded device, but this added grounding measure can be used at

the discretion of the installer (for instructions, see the Hardware Reference Manual).

Twisted Pair Cable Pinouts and RJ-45 LEDs

The DXLink port (RJ-45 connector) on the rear of the Transmitters uses twisted pair

cable. FIG. 5 shows two pinouts that can be used. FIG. 6 shows LEDs for the port.

Before installing the Transmitter:

 Wallplate TX – remove mounting bracket.

 If a network connection is required, set #3 Toggle to ON.

 If gang box is not already installed, install it now.

To install the Wallplate Tx:

1. Attach the Wallplate TX mounting bracket to the gang box.

2. Attach a twisted pair cable from the DXLink Input Board on the switcher through

the mounting bracket to the DXLink connector on rear of Wallplate TX (FIG. 7).

3. Reattach the unit to the mounting bracket.

To install the Decor Wallplate TX:

1. Attach a twisted pair cable from the DXLink Input Board on the switcher to the

DXLink connector on the rear of the Decor Wallplate TX.

2. Attach unit to back box with four screws through the large screw holes.

3. Check LEDs for normal display (see table on the next page).

FIG. 1

WALLPLATE TX: FG1010-320-WH (LEFT) AND DECOR TX: FG1010-325-WH (RIGHT)

FIG. 2 WALLPLATE TX (FRONT & REAR) USED W/DXLINK INPUT BOARD IN ENOVA DGX 16

FIG. 3 DIP SWITCH ON REAR OF WALLPLATE TX (LEFT); ON FRONT OF DECOR TX (RIGHT)

Both available

in white (WH)

and black (BL)

Twisted pair cable

HDMI cable

Enova DGX 16

Source device

DXLink

Multi-Format

Wallplate TX

(Front) (Rear)

DXLink

Input Board

DIP switch

FIG. 4

WALLPLATE TX MOUNTING BRACKET

FIG. 5 RJ-45 CONNECTOR PINOUTS

FIG. 6 DXLINK PORT LEDS

Wallplate TX

mounting bracket

Use screw holes indicated with “X”s below:

US flush mount inside wall

EU flush mount inside wall

UK surface mount exterior wall or

UK flush mount inside wall

Green LED

On - Connection is active

Off - Connection is not active

Yellow LED

On - Authenticated HDCP

Blinking - Video active; no HDCP

Off - No Video

Wallplate TX

Decor Wallplate TX

Produkt Specifikationer

Mærke:	AMX
Kategori:	Ikke kategoriseret
Model:	DX-TX-DWP
Type:	AV sender
Bredde:	103.1 mm
Dybde:	88.4 mm
Højde:	57.2 mm
Vægt:	340 g
Antal pr. pakke:	1 stk
Produktfarve:	Sort
Opbevaringstemperatur (T-T):	-30 - 70 °C
Relativ luftfugtighed ved drift (H-H):	5 - 85 %
Relativ luftfugtighed ved opbevaring (H-H):	0 - 90 %
HDCP:	Ja
Driftstemperatur (T-T):	0 - 40 °C
Maksimal opløsning:	1920 x 1200 pixel
Forbindelsesteknologi:	Ledningsført
LED-indikatorer:	Ja
Antal USB-porte:	1
Lydindgang:	1
Maksimal overførselsafstand:	100 m
Maksimal opdateringshastighed:	60 Hz
USB-stik type:	Mini-USB B
HSMI-indgang:	1
VGA (D-Sub) indgangsporte:	1
Understøttede kabeltyper:	Cat6, Cat6a, Cat7
Båndbredde:	10.2 Gbit/sek.