AMX DXFP-TX-4K60 Manual

AMX Ikke kategoriseret DXFP-TX-4K60

Læs gratis den danske manual til AMX DXFP-TX-4K60 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om AMX DXFP-TX-4K60, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
QUICK START GUIDE
DXLink™ 4K60 HDMI Fi
ber Transmitter/Receiver
Mounting Options (Rack Trays and Mounting Brackets)
The DXFP-TX-4K60 and DXFP-RX-4K60 can be mounted using V Style Surface Mounting
Brackets, V Style Single Module Pole Mounting Kit, or NMX-VRK V-Style Rack Shelf.
For details, see www.amx.com
IMPORTANT: Wh
en mounting under a surface, the module should be mounted upright and
lowered in the mounting bracket slots to provide an airflow gap between the surface and
the vent holes. If not using V Style brackets, be sure to leave a gap between the top of
the unit and the surface for heat to escape.
1 2 3 4
ON
ID USB MODE
DIP Switch Toggles – Default OFF (for Auto-setup, see next page)
Before installing the units, find the scenario you are using in the table below and set the
DIP switch toggles accordingly. Toggle #4 is reserved for future functionality.
For standalone pair upgrades, set Toggles #1-2-3 to ON and connect one unit to Controller.
** In standalone setup using NetLinx control of DXLink serial/IR ports, only one of the
DXLink fiber units should be connected to network (the unit with #1 Toggle enabled).
COMMON SCENARIOS TOGGLES
Standalone Setup 1 - 2 - 3
AV signals only (plus serial/IR passthrough) OFF - OFF - OFF
AV with Ethernet passthrough to networked device (plus serial/IR
passthrough)*
ON - OFF - OFF
AV with NetLinx control of TX/RX unit and serial/IR ports** ON - ON - ON
AV with NetLinx control of TX/RX unit and serial/IR ports, plus Ethernet
passthrough to network device*
ON - ON - ON
Switcher Setup (TX/RX with Enova DGX/DGX 100 Series Switcher) 1 - 2 - 3
AV signals only OFF - OFF - OFF
AV with Ethernet passthrough to networked device* ON - OFF - OFF
AV with NetLinx control of TX/RX unit and serial/IR ports OFF - OFF - ON
AV with NetLinx control of TX/RX unit and serial/IR ports, plus Ethernet
passthrough to network device*
ON - OFF - ON
• Endpoint Mode (Switcher) – connect one or more to a switcher with an integrated
• Endpoint Mode (Standalone) – connect TX/RX pair directly to each other with one
connected to a NetLinx Central Controller via LAN or directly to Controller.
• Extender Mode (Standalone) – connect TX/RX pair
directly to each other.
These Modules support InstaGate Pro® and SmartScale® Technology.
The Hardware Reference Manual - DXLink 4K60 Fiber Transmitter/Receiver contains
complete documentation (including full specifications and supported input and output
resolutions); for details, see www.amx.com.
System Setup
The DXFP-TX-4K60 and DXFP-RX-4K60 work with a switcher that supports DXLink
Technology or as a stand-alone pair to transmit audio, video and control signals. The
Transmitter receives audio and video from the HDMI source and transmits both audio
and video over the fiber optic cable. This DXLink fiber optic cable can be connected directly
to a DXLink fiber receiver or to a DXLink fiber input on a DXLink switcher where it can be
routed to a DXLink fiber output and connected to a DXLink fiber receiver. The DXLink fiber
receiver converts the DXLink fiber input to HDMI and analog audio outputs. On the
transmitter, stereo audio connections are provided a
s a supplemental audio input. Both the
transmitter and the receiver support RS-232 for serial data transfer, USB, IR, and Ethernet.
FIG. 1
DIP SWITCH TOGGLES ENABLE/DISABLE SPECIAL FUNCTIONALITY
Overview
The DXFP-TX-4K60 and DXFP-RX-4K60 transmit HDMI, audio, USB and control over
fiber optic cable. The TX also has an HDMI loop out. DXLink fiber modules can be set
up in one of three ways:
FIG. 3
HDMI IN
Fiber optic cable
HDMI OUT
Source Device
Destination Device
DXLINK FIBER TX AND RX AS EXTENDER SOLUTION
FIG. 2
DXLINK Fiber Transmitter
DXLINK Fiber Receiver
HDMI IN
Fiber optic cable
Fiber optic cable
HDMI OUT
Destination Device
DXLINK Fiber
Output Board
LAN 100/1000
Source Device
AC
DC
FLT
AC
DC
FLT
DXLINK Fiber
Input Board
DXLINK FIBER TX AND RX AS ENDPOINTS WITH COMPATIBLE DXLINK FIBER EQUIPMENT
F
IG. 4
ICS LAN 10/100 Port
The ICS LAN 10/100 port uses twisted pair cable. FIG. 4 shows the LEDs for this port.
ICS LAN (RJ45) PORT
On - Speed status is 100 Mbps
Off - Speed status is 10 Mbps
Yellow LED:
On - Link status is active
Off - Link status is not active
Green LED:
FIG. 5 FIBER OPTIC TRANSCEIVER MARKED BLACK (MULTIMODE)
Latch and/or label color
Dust plug
SFP+ = enhanced small form-factor
pluggable fiber optic transceiver rated
at 10 Gbps transmission data rate.
Fiber Optic Transceivers
The DXLink Fiber Transmitters and Receivers use SFP+ fiber optic transceivers. Fiber
optic transceivers are self-contained modules that send and receive optical signals over
fiber cable. DXLink SFP+ fiber optic transceivers is multimode and must be wired with
the corresponding cable type. Multimode transceivers support bidirectional and
unidirectional communication.
Attaching Signal, Transport, and Control Cables
Important Cabling Requirements and Considerations
•
• LC Duplex conforming to ANSI TIA-EIA 604-10 (FOCIS 10A)
• DXLink Fiber multimode transceivers use OM3 50/125 μm multimode fiber optic
cable type over distances of up to 984 feet (300 m)*
• Do not create a network (Ethernet) loop. A network loop is created when the
enclosure and one or more of its DXLink Fiber units connect to a common LAN.
Fiber optic cable with LC termination for snap coupling with SFP+ transceivers
* Connect ICS LAN port of DXLink fiber unit to network device (e.g., laptop, IP controlled
projector, ICSLan Device). In standalone setup, connect ICS LAN port of other DXLink
unit to network.
* Cable quality is a determining factor for the maximum length of cable runs.
WARNING：DXLink Fiber units use laser transceiver, which are Class 1 Eye Safe per
IEC 60825-1/CDRH requirements. While the Class 1 category indicates that the invisible
laser used is safe, we recommend avoiding direct eye exposure when using any optical
fiber products (See OSHA directive referenced in the “Hardware Reference Manual”).
DXLINK Fiber Transmitter DXLINK Fiber Receiver
Controller.

Produkt Specifikationer

Mærke: AMX
Kategori: Ikke kategoriseret
Model: DXFP-TX-4K60

Har du brug for hjælp?

Hvis du har brug for hjælp til AMX DXFP-TX-4K60 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret AMX Manualer

AMX

AMX NMX-DEC-N1233A Manual

26 November 2025
AMX

AMX DGX-O-DXF-MMS Manual

14 September 2025
AMX

AMX DVX-2250HD Manual

14 September 2025
AMX

AMX Vision² Manual

14 September 2025
AMX

AMX NMX-ENC-1100 Manual

14 September 2025
AMX

AMX UPC20+ Manual

14 September 2025
AMX

AMX DGX-I-DXL Manual

14 September 2025
AMX

AMX DGX-O-HDMI Manual

14 September 2025
AMX

AMX EXB-MP1 Manual

14 September 2025
AMX

AMX DGX-I-DXF-SMD Manual

14 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vevor

Vevor LX-PMMA-24*36 Manual

29 November 2025
Twelve South

Twelve South BookBook Manual

29 November 2025
Vevor

Vevor SSH-1S-100-2 Manual

29 November 2025
Vevor

Vevor GYZU-6T Manual

29 November 2025
Vevor

Vevor H10263-57 Manual

29 November 2025
Vevor

Vevor SP-HL-P202010-10A Manual

29 November 2025
Yamaha

Yamaha PLG150-DR Manual

29 November 2025
Extech

Extech 380460 Manual

29 November 2025
Blumfeldt

Blumfeldt Versagrow Manual

29 November 2025
Vevor

Vevor EVS-15L Manual

29 November 2025