AMX HPA-MYT-TX Manual

AMX Ikke kategoriseret HPA-MYT-TX

Læs gratis den danske manual til AMX HPA-MYT-TX (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 63 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 32 anmeldelser. Har du et spørgsmål om AMX HPA-MYT-TX, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

QUICK START GUIDE

HPA-MYT-TX/RX MyTurn

Source Selector

Overview

The HPA-MYT-TX MyTurn™ Source Selector Button (FG554-21) connects to the end of

a standalone MyTurn-Ready cable (HDMI, Mini-DP, DP, RGB, USB), or one thats installed

in a Retractable Cable Module (RCM). A user presses the button to send their device

content to a conference room display. When pressed, the button wirelessly transmits a

signal to the HPA-MYT-RX MyTurn Source Selector Wireless Receiver (FG554-23) that is

wired to an AMX master controller or an AMX switching device, such as a Solecis SDX or

Enova DVX. When used with a Solecis SDX, simple switching can be implemented with

no NetLinx programming required. Each MyTurn Source Selector Receiver can

accommodate up to 8 MyTurn Source Selector Buttons.

MyTurn Source Selector Buttons and Receivers have the following user features:

MyTurn Source Selector Button

• Push button – activates input at switcher to display device content

MyTurn Receiver

• Select Button – press momentarily to switch ports (indicated by LEDs)

– press and hold to enter “pairing” mode

– press and hold during power up to reset to factory defaults

Product Specifications

MyTurn Source Selector Solution in a Conference Room

The eight outputs on the rear of the MyTurn Source Selector Receiver connect using

Phoenix connector to the SW inputs on Solecis SDX-510M-DX, or GPIO inputs on NI

Controllers or Enova DVX devices. When the MyTurn Source Selector Button paired with

that I/O port is triggered, the MyTurn Source Selector Receiver activates the AMX

device “SW” input or I/O port, signaling the system to switch the display to that port.

Following are examples of two typical MyTurn Source Selector installations.

Solecis SDX-410/510/810 Switchers

The MyTurn Source Selector Receiver connects to the AMX Solecis front AXLINK port

for power and ground as outlined in FIG. 3. Output ports (1 through 8) are wired to the

corresponding Solecis rear “SW” input that has a MyTurn Source Selector Button

equipped cable connected to it. This solution can be implemented without NetLinx

programming since the SW port is directly connected to the Receiver.

Note: Only on the SDX-510-DX, set dipswitch #4 in the ON position (Direct Mode). This

will set the external button behavior to be in direct mode by default. Once the

dipswitch is turned ON the SDX-510-DX must be rebooted in order for the setting to

take effect.

Enova DVX Master/NetLinx Integrated Controller

The MyTurn Source Selector Receiver connects to an AMX DVX Master or a NetLinx

Controller using the GPIO interface as outlined in FIG. 4. The GPIO port can deliver

Power and Ground as well as receive switch inputs 1-8.

This solution requires NetLinx programming to correlate a GPIO input button event to

switch to a predetermined port on the DVX.

MyTurn Source Selector Receiver Installation

Refer to the following steps to install the MyTurn Source Select Buttons and Receivers.

Note: 3M Reclosable Fastener strips are provided to attach the receiver under the table.

The adhesive strips require 24 hours dwell time to obtain 90% adhesion before

applying a load or disengaging assemblies (50% bond strength after 20 minutes,

90% after 24 hours.

Note: The MyTurn Source Selector Wireless Receiver must be installed within 10 meters

(32 ft) of the MyTurn Source Selector Buttons. Care must be taken to minimize

metal obstructions to the wireless signal (i.e., equipment racks).

Note: The Rx must receive the 8-15VDC power from a distance of 3 meters or less.

1. Clean surfaces and with alcohol wipes and apply the Velcro strips to the receiver

and table mounting location 24 hours in advance for strong adhesion.

2. Wire the Solecis, DVX, or NX/NI Master Controller using 24 AWG wire in the

Phoenix screw terminals. Ensure Power and Ground are connected as shown

(FIG. 5). Use the AXLINK ports for Power and Ground if connecting to a Solecis as

FIG. 1

HPA-MYT-TX MYTURN BUTTON (LEFT) AND HPX-MYT-RX MYTURN RECEIVER (RIGHT)

HPA-MYT-TX SPECIF ICATIONS

Dimensions • 1.421” x .645” x 0.40” HWD (36mm x 16mm x 10mm)

Power: • Integrated 3VDC coin-cell battery (not replaceable)

• Expected Lifetime: 30K presses or 5/6 years of typical usage

Environment • Operating Temperature: 32° F (0° C) to 122° F (50° C)

• Operating Humidity: 20% to 85% RH

Top Panel: • Push-button

Compatibility: Retractable Cable Module (RCM) Assemblies:

• FG552-32 - HDMI 4K60 RCM with MyTurn-Ready Cable

• FG552-33 - DisplayPort 4K60 RCM with MyTurn-Ready Cable

• FG552-36 - Mini DisplayPort 4K60 RCM with MyTurn-Ready Cable

• FG552-35 - RGB with Stereo RCM with MyTurn-Ready Cable

• FG552-37 - USB 3.0 RCM with MyTurn-Ready Cable

Flat Cable Assemblies:

• FG10-2192-xx - HDMI 4K60 MyTurn-Ready Flat Cable (xx=16 or 32 ft)

• FG10-2193-16 - DisplayPort 4K60 MyTurn-Ready Flat Cable

• FG10-2195-16 - RGB with Auto MyTurn-Ready Flat Cable

• FG10-2196-16 - Mini DisplayPort 4K60 MyTurn-Ready Flat Cable

• FG10-2197-16 - USB MyTurn-Ready Flat Cable

Accessories: • HPX-2BTN-8ACC - 8 button inserts and 8 cable bands kit (optional)

• Quick Start Guide Included

• 2 TX Button mounting clips - one for VGA, one for HDMI/DP/mDP/USB

HPA-MYT-RX SPECIF ICATIONS

Dimensions (HWD) • 3.21” x 2.54” x 0.55” HWD (82.55mm x 69.85mm x 15.24mm)

Enclosure: • Polycarbonate plastic with matte finish

Input Voltage: • 8-15 VDC on the “+12V” input operates LEDs and I/O outputs

to Solecis, NI-Controller or DVX Switcher

• The Rx must receive the 8-15VDC power from a distance of 3

meters or less.

Environment • Operating Temperature: 0° C (32° F) to 50° C (122° F)

• Operating Humidity: 20% to 85% RH

Front Panel: • 8 Yellow LEDs

• 1 Push button for pairing or port selection

Rear Panel: • 1 x 6 Phoenix screw-terminal - I/O 1-4 and Power/Ground

• 1 x 4 Phoenix screw-terminal - I/O 5-8

• 1 Green LED indicates power is applied, and flickers when any

wireless transmission is detected.

Accessories: • Quick Start Guide Included

• 3M Reclosable Fastener strips for mounting the receiver under a

table

• Phoenix Plugs (4 and 6 port)

MyTurn TX Button

Pairing and port

select button

MyTurn Receiver

FIG. 2 MYTURN TO AMX SOLECIS DIGITAL SWITCHER CONNECTION EXAMPLE

FIG. 3 MYTURN SOURCE SELECTOR SW CONNECTION (1 CONNECTION SHOWN)

MyTurn-Ready Cables

in a HydraPort RCM

HydraPort

Chassis

Solecis SDX

MyTurn Button

HDMI

mDP

MyTurn-Ready

HDMI Cable

Status LED

MyTurn-Ready HDMI Cable

Source End

Solecis SDX-Front

Solecis SDX-Rear

HPX-MYT-RX Receiver

HPX-MYT-TX

Button

Display End

Produkt Specifikationer

Mærke:	AMX
Kategori:	Ikke kategoriseret
Model:	HPA-MYT-TX

Har du brug for hjælp?

Hvis du har brug for hjælp til AMX HPA-MYT-TX stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret AMX Manualer

AMX NMX-DEC-N1233A Manual

26 November 2025

AMX DGX-O-DXF-MMS Manual

14 September 2025

AMX DVX-2250HD Manual

14 September 2025

AMX Vision² Manual

14 September 2025

AMX NMX-ENC-1100 Manual

14 September 2025

AMX UPC20+ Manual

14 September 2025

AMX DGX-I-DXL Manual

14 September 2025

AMX DGX-O-HDMI Manual

14 September 2025

AMX EXB-MP1 Manual

14 September 2025

AMX DGX-I-DXF-SMD Manual

14 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vevor LX-PMMA-24*36 Manual

29 November 2025

Twelve South BookBook Manual

29 November 2025

Vevor SSH-1S-100-2 Manual

29 November 2025

Vevor GYZU-6T Manual

29 November 2025

Vevor H10263-57 Manual

29 November 2025

Vevor SP-HL-P202010-10A Manual

29 November 2025

Yamaha PLG150-DR Manual

29 November 2025

Extech 380460 Manual

29 November 2025

Blumfeldt Versagrow Manual

29 November 2025

Vevor EVS-15L Manual

29 November 2025