AMX HydraPort HPX-AV102 Manual

AMX Ikke kategoriseret HydraPort HPX-AV102

Læs gratis den danske manual til AMX HydraPort HPX-AV102 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 9 anmeldelser. Har du et spørgsmål om AMX HydraPort HPX-AV102, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

QUICK START GUIDE

HPX-AV102-USB-R

USB 3.0 Module with Retractable

MyTurn

Ready Cable

Overview

The HydraPort

Retractable Cable Module is designed to be used in conjunction with

the HPX-600/900/1200/1800 or the Hydraport Touch (7”/10”) Connection Port base

assembly, to provide the convenience of various types of cables in a HydraPort System.

The HPX-AV102-USB-R USB 3.0 Module with Retractable Cable (FG552-37) provides a

USB 3.0 cable in a retractable spool that mounts into the HydraPort base assembly

(FIG. 1). USB 3.0 cable features transmission speeds of up to 5 Gbit/s and supports

charging devices via 4.5W: 5V@900mA charging current.

With the MyTurn™ Source Selection Button (FG554-21) optional accessory,

participants can send their content to a display at the press of a button without moving

from their seat. Any MyTurn-Ready cable may be equipped with the MyTurn solution.

See “Optional MyTurn™ Source Selector Button” on page 2.

Installation

Warning! - Do not attempt to open the retractable cable module enclosure. There are

no serviceable parts inside the module.

- Opening the module enclosure may result in an uncontrolled release of spring

forces which could cause serious injury and/or equipment damage.

- Opening the module enclosure will void the product warranty.

Warning! - installation of the Hydraport in the table should ensure the pull-out length

of the cable can reach all potential users of connectivity, as excessively pulling on a

fully extended cable can irreparably damage the retractor module.

Caution: Only use a hand-held #2 Phillips-head screwdriver for mounting this unit. Over-

tightening the screws can hinder performance or damage the unit.

For existing HPX installations, the HPX base must be removed from the mounting

surface. See “Existing Installations” on page 2. for HPX Base removal instructions.

1. Remove the (silver) pivot screw in the center of the End Cap (FIG. 2). There is an

internal tooth washer underneath it. Keep them together for re-installation.

2. Remove the four (black) sheet metal screws that secure the two-piece End Cap to

the HPX assembly (additional top two screws only on one-piece end cap models).

3. Gently slide the End Cap out of the HPX base assembly.

The HPX-AV102-USB-R RCM cable cartridge mounts from underneath the table to

simplify installation and upgrade of retractable cable modules. This version RCM has a

detachable mounting collar that is installed into the Hydraport base first and then the

cable cartridge is reattached to the mounting collar

Securely holding the HPX-AV102-ETH-R RCM, extract enough cable to lay the cable

cartridge on the floor while installing the mounting collar into the HPX Base Assembly

(~3ft). When extracting 5 foot (1.5m) cable from the RCM, follow these simple steps:

4. Pull up to 1.5 meters of cable straight up out of the RCM and then lay it down.

5. Watch for a red tape on the cable when extracting. It is a warning to slow pull for

the final 1 foot to avoid damage to the RCM (FIG. 3).

6. Pull the cable cartridge trigger (FIG. 4) to release the mounting collar tongue.

7. Lift the mounting collar away from the cable cartridge until the tongue is clear and

then slide to the side to clear the hook.

8. Feed the mounting collar up through the table cutout to reach the HPX base

assembly. Align the mounting notches on the mounting collar with the mounting

rails on the HPX (FIG. 4).

Note: Module mounting collars are notched in a “tongue and groove" type fashion

to ensure that all modules are oriented correctly in the HPX. Note the orientation of

the notched mounting collar on each module before sliding the module(s) into the

HPX assembly.

9. Slide the mounting collar into position.

10. Install any remaining module mounting collars into the HPX base.

Re-Install the End-Cap

Caution: Do not use a high-powered torque screw driver. Over-tightening these screws

can damage the product.

1. Align the mounting notches on the end cap with the mounting rails on the HPX base.

2. Slide the End Cap into the HPX base until it is fully inserted against the end of the

base assembly. Watch out for the tension spring under the pivot pawl popping the

pivot pawl off the end cap while pressing against the lid pivot point.

3. Secure the End Cap with the 4 to 6 (black) sheet metal screws (FIG. 2).

4. Replace the (silver) pivot screw in the center of the End Cap.

FIG. 1

HPX-AV102-USB-R USB 3.0 MODULE WITH RETRACTABLE CABLE

FIG. 2 HPX BASE ASSEMBLY - MOUNTING/PIVOT SCREW LOCATIONS

Retractable 5 foot (1.5 meter) USB MyTurn Ready cable

connects to Source device

Cable Retract Push Button

Mounting notches (both sides)

5 foot Cable Pigtail (1.5 meter)

Pull trigger to initiate

separation of the mounting

collar from cartridge

Slide-hook and catch secures

mounting collar to cartridge

has a Male Type A connection,

or use the included adapters to

convert to Female Type A or Male Type B

Remove Pivot Pawl

and Pivot Screw

Remove four remaining

sheet metal screws

(highlighted)

Remove top two screws

(only on one-piece end

cap models)

FIG. 3 EXTRACTING CABLE - WARNING BAND

FIG. 4 HPX-AV102-USB-R MOUNTING COLLAR REMOVAL

FIG. 5 RETRACTABLE CABLE MODULE - MOUNTING INTO AN HPX BASE ASSEMBLY

Warning Tape

4 Feet

1 Foot

Slow Pull

Pull

Trigger

Detachable

Mounting

cable cartridge

Collar

DO NOT twist the

detached cable

cartridge. If a twist

exists in the cable

when remounted the

Mounting

tongue

retractor will not

fully retract..

Slide the mounting

notches on both sides

of the mounting collar onto

the mounting rails on both

sides of the HPX Base

HPX Base Top Surface

Table cutout

Mounting

Collar

Retract Button

HARMAN. Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarks of their respective

companies.

AMX does not assume responsibility for errors or omissions. AMX also reserves the right to alter specifications without prior notice at any time.

The AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax 469.624.7153

AMX (UK) LTD, AMX by HARMAN - Auster Road, Clifton Moor, York, YO30 4GD United Kingdom • +44 1904-343-100 • www.amx.com/eu/

93-0552-37 REV: B

Last Revised: 9 /21/2016

Mount the HPX into the Mounting Surface

Caution: Do not use a high-powered torque screw driver. Over-tightening these screws

can damage the product.

Note: For detailed instructions on installing the HPX base assembly, refer to the HPX-

600/900/1200/1800 and HydraPort Touch (7”/10”) Installation Guides (available

online at www.amx.com).

1. Carefully insert the HPX base into the cutout in the mounting surface.

2. Tighten the four mounting screws (FIG. 8) located inside and at each end of the

HPX base assembly, to rotate the retaining tabs (FIG. 9) into locking position

under the mounting surface.

3. Minding the twist in the cable, feed the excess cable up through the mounting

collar and insert the cable cartridge hook into the mounting collar cutout.

Note: If a twist in the cable occurs from rotating the cassette before insertion, the

cable will bind and will not retract fully.

4. Push the cable cartridge trigger up onto the mounting collar tongue until it

latches (opposite of FIG. 4).

5. Use the Push button to retract the cable into the cartridge.

6. Attach the display ends of the cables as necessary.

7. Use cable ties to secure cable bundles as necessary.

The under-table end connector is a Male Type A. Included adapters:

• Female Type A to Female Type A (resulting in a Female Type A)

• Female Type A to Male Type B (resulting in a Male Type B)

Mounting Dimensions

FIG. 6 provides dimensions for the retractable cable module, when installed in an HPX-

600/900/1200/1800 or HPX-MSP-07/10 base assembly.

Optional MyTurn™ Source Selector Button

The optional HPA-MYT-TX MyTurn™ Source Selector Button (FG554-21), it clips into the

specially designed groove built into the end of a MyTurn ready cable. Users press to

send the content on their device to the display. When pressed, the button transmits a

signal to an optional receiver (FG554-23) that plugs directly into an AMX switching

device such as a Solecis SDX, Enova DVX, or NX Series Controller.

MyTurn Source Selector Buttons are illuminated briefly when that specific device is

selected, making it easy to determine whose content is being shown on the display at

any given time. Refer to the HPA-MYT-TX documentation for further details.

Existing Installations

For existing HPX installations, the HPX Base Assembly must be removed from the table

surface before the Retractable Cable Modules can be installed.

Note: It may be necessary to reorient existing 1st generation RCMs in the chassis to

ensure they fit against the non lip edge of MyTurn-Ready 2nd generation RCMs.

Otherwise a 1/2 M blank panel (FG558-01) or other non retractable cable module needs

to be installed between the 1st Generation and MyTurn-Ready 2nd Generation RCMs.

1. Cut/remove any cable ties that restrict the removal of the HPX Base Assembly.

2. Loosen four screws located inside and at each end of the HPX base assembly

(FIG. 8), in order to rotate the retaining tabs from under the mounting surface.

Note: When the cover of the HPX base is open, only two of these screws are visible.

To access the other two screws, tip the cover over to the opposite open position.

3. Once the retaining tabs have been rotated out from under the mounting surface,

the HPX assembly can be lifted away from the mounting surface.

FIG. 9 provides a cutaway view of the End Cap, showing the retaining tabs

highlighted in both the loose position and the tightened (secure) position.

4. Return to the installation section at the bottom left column of page 1 to continue

with installing the RCM into the HPX Base assembly.

Replacing MyTurn-Ready RCMs

Removal of the HPX Base assembly is not required to replace this RCM:

1. Detach the cable cartridge from the mounting collar (FIG. 4).

2. From the top of the mounting collar, press a small flat blade screwdriver into the

notch on the split side of the pop out panel and pop it out of place (FIG. 10)..

3. Slip the cable out through the mounting collar panel.

4. Replace with new RCM in reverse order ensuring the cable is not twisted and the

pop out panel split is oriented towards the notch in the collar.

Additional Documentation

Refer to the Products > Architectural Connectivity catalog page on www.amx.com

(Dealer Site) for additional product documentation.

FIG. 6

RCM MODULE (INSTALLED IN AN HYDRAPORT BASE) - DETAILED DIMENSIONS

FIG. 7 MYTURN™ SOURCE SELECTION BUTTON (FG554-21)

5 ft Cable Pigtail

HPX Base Assembly Top

Mounting Surface Top

Removable RCM

cable cartridge

mounted to

(285.3 mm)

11.2 inches maximum

(202.5 mm)

8 inches

Removable RCM

mounting collar

mounted to HPX

Base

mounting collar

FIG. 8 HPX BASE ASSEMBLY (SHOWN MOUNTED) - MOUNTING SCREWS LOCATIONS

FIG. 9 HPX BASE ASSEMBLY (SHOWN MOUNTED) - MOUNTING SCREWS LOCATIONS

FIG. 10 RCM MOUNTING COLLAR POP-OUT PANEL

Retaining tab

(to secure the unit)

shown tightened

Retaining tab

(to remove the unit)

shown loosened

Mounting Collar

Pop-out panel

Slip cable through

slot in panel

Notch in Collar used to

pop out panel

Produkt Specifikationer

Mærke:	AMX
Kategori:	Ikke kategoriseret
Model:	HydraPort HPX-AV102

Har du brug for hjælp?

Hvis du har brug for hjælp til AMX HydraPort HPX-AV102 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret AMX Manualer

AMX HPA-MYT-RX Manual

5 August 2025

AMX NMX-WP-N2510 Manual

30 Juli 2025

AMX NMX-ACC-N9101 Manual

30 Juli 2025

AMX NMX-ACC-N9206 Manual

30 Juli 2025

AMX NMX-ENC-N2312 Manual

30 Juli 2025

AMX NMX-ATC-N4321 Manual

30 Juli 2025

AMX RMS-ENT Manual

30 Juli 2025

AMX RMS-ENT-SMA Manual

30 Juli 2025

AMX NMX-VRK Manual

30 Juli 2025

AMX HPA-MYT-TX Manual

16 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

B-Tech BT8390-SA Manual

18 August 2025

Festo ZSB-1/8-B Manual

18 August 2025

D-Link DI-701 Manual

18 August 2025

Festo SIEF-M30B-NS-S-L Manual

18 August 2025

Festo P.BE-CMMP-SC-SW-DE Manual

18 August 2025

Festo VACC-S18-120-K4-1U-KS4ME Manual

18 August 2025

Festo SIED-M18NB-ZO-S-L Manual

18 August 2025

Festo P.BE-CP-FB11-E-IT Manual

18 August 2025

Martin Exterior Dot-4 Pro Manual

18 August 2025

Festo SOE4-FO-L-HF2-1P-M8 Manual

18 August 2025