AMX HydraPort HPX-AV103 Manual

AMX Ikke kategoriseret HydraPort HPX-AV103

Læs gratis den danske manual til AMX HydraPort HPX-AV103 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om AMX HydraPort HPX-AV103, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

QUICK START GUIDE

RGB+Stereo Module with Retractable

MyTurn

Ready Cable

HPX-AV103-RGB+A-R

Overview

The Hydraport Retractable Cable Modules are designed to be used in conjunction with

the HPX-600/900/1200 or the HydraPort Touch (7”/10”) Connection Port base

assembly, to provide the convenience of various types of cables in a Hydraport System.

The HPX-AV103-RGB+A-R RGB+Stereo Module with Retractable MyTurn-Ready Cable

(FG552-35) provides an RGB+Stereo cable in a retractable spool that mounts into the

Hydraport base assembly (FIG. 1).

With the addition of a MyTurn™ Source Selection Button (FG554-21) optional

accessory, participants can send their content to the display at the press of a button

without moving from their seat. Any MyTurn-Ready cable may be equipped with the

MyTurn solution See FIG. 1.

Note that the retractable cable (which connects to the Source device) features two

3.5mm ports, one on either side of the RGB connector. One connects to the source

device’s audio output (via the Stereo Audio Patch Cable). The second is an inactive

storage port for the Stereo Audio Patch Cable.

Note: Always keep the Stereo Audio Patch Cable plugged into this storage port when not

in use. This is to both protect the plug, and to avoid the potential for noise on this cable.

Installation

Warning! - Do not attempt to open the retractable cable module enclosure. There are

no serviceable parts inside the module.

- Opening the module enclosure may result in an uncontrolled release of spring

forces which could cause serious injury and/or equipment damage.

- Opening the module enclosure will void the product warranty.

Warning! - installation of the Hydraport in the table should ensure the pull-out length

of the cable can reach all potential users of connectivity, as excessively pulling on a

fully extended cable can irreparably damage the retractor module.

Caution: Only use a hand-held #2 Phillips-head screwdriver for mounting this unit. Over-

tightening the screws can hinder performance or damage the unit.

For existing HPX installations, the HPX base must be removed from the mounting

surface. See “Existing Installations” on page 2 for HPX Base removal instructions.

1. Remove the (silver) pivot screw in the center of the End Cap (FIG. 2). There is an

internal tooth washer underneath it. Keep them together for re-installation.

2. Remove the four (black) sheet metal screws that secure the two-piece End Cap to

the HPX assembly (additional top two screws only on one-piece end cap models).

3. Gently slide the End Cap out of the HPX base assembly.

The HPX-AV103-RGB+A-R RCM cable cartridge has a new mounting scheme from

underneath the table to simplify installation and upgrade of retractable cable modules.

This version RCM has a detachable mounting collar that is installed into the Hydraport

base first and then the cable cartridge is reattached to the mounting collar.

Securely holding the HPX-AV103-ETH-R RCM, extract enough cable to lay the cable

cartridge on the floor while installing the mounting collar into the HPX Base Assembly

(~3ft). When extracting 5 feet (1.5m) cable from the RCM, follow these simple steps:

4. Pull up to 1.5 meters of cable straight up out of the RCM and then lay it down.

Watch for red tape on the cable when extracting. It is a warning to slow pull for

the final 1 foot to avoid damage to the RCM.

6. Pull the cable cartridge trigger (FIG. 4) to release the mounting collar tongue.

7. Lift the mounting collar away from the cable cartridge until the tongue is clear and

then slide to the side to clear the hook.

8. Feed the mounting collar up through the table cutout to reach the HPX base

assembly. Align the mounting notches on the mounting collar with the mounting

rails on the HPX (FIG. 5).

Note: Module mounting collars are notched in a “tongue and groove" type fashion

to ensure that all modules are oriented correctly in the HPX. Note the orientation of

the notched mounting collar on each module before sliding the module(s) into the

HPX assembly. On RCMs, ensure the retract buttons are all on the same side.

9. Slide the mounting collar into position.

10. Install any remaining module mounting collars into the HPX base.

Re-Install the End-Cap

Caution: Do not use a high-powered torque screw driver. Over-tightening these screws

can damage the product.

1. Align the Mounting Notches on the End Cap with the Mounting Rails on the HPX base.

2. Slide the End Cap into the HPX base until it is fully inserted against the end of the

base assembly. Watch out for the tension spring under the pivot pawl popping the

pivot pawl off the end cap while pressing against the lid pivot point.

3. Secure the End Cap with the 4 to 6 (black) sheet metal screws (FIG. 2).

4. Replace the (silver) pivot screw in the center of the End Cap.

FIG. 1

HPX-AV103-RGB-A+R RGB+AUDIO MODULE WITH RETRACTABLE CABLE

FIG. 2 HPX BASE ASSEMBLY - MOUNTING/PIVOT SCREW LOCATIONS

Retractable 5 foot (1.5 meter) RGB MyTurn Ready cable

connects to Source device

Cable Retract Push Button

Mounting notches (both sides)

5 foot cable pigtail (1.5 meter)

with RGB+Audio connector

connects to display device

Pull trigger to initiate

separation of the mounting

collar from cartridge

Slide-hook and catch secures

mounting collar to cartridge

Remove Pivot Pawl

and Pivot Screw

Remove four remaining

sheet metal screws

(highlighted)

Remove top two screws

(only on one-piece end

cap models)

FIG. 3 EXTRACTING CABLE - WARNING BAND

FIG. 4 HPX-AV103-RGB+A-R MOUNTING COLLAR REMOVAL

FIG. 5 RETRACTABLE CABLE MODULE - MOUNTING INTO AN HPX BASE ASSEMBLY

Warning Tape

4 Feet

1 Foot

Slow Pull

Pull

Trigger

Detachable

Mounting

cable cartridge

Collar

DO NOT twist the detached

cable cartridge. If a twist

exists in the cable when

remounted, the retractor

will not fully retract.

Mounting

tongue

Slide the mounting

notches on both sides

of the mounting collar onto

the mounting rails on both

sides of the HPX Base

HPX Base Top Surface

Table cutout

Mounting

Collar

Retract Button

Produkt Specifikationer

Mærke:	AMX
Kategori:	Ikke kategoriseret
Model:	HydraPort HPX-AV103

Har du brug for hjælp?

Hvis du har brug for hjælp til AMX HydraPort HPX-AV103 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret AMX Manualer

AMX NMX-DEC-N1233A Manual

26 November 2025

AMX DGX-O-DXF-MMS Manual

14 September 2025

AMX DVX-2250HD Manual

14 September 2025

AMX Vision² Manual

14 September 2025

AMX NMX-ENC-1100 Manual

14 September 2025

AMX UPC20+ Manual

14 September 2025

AMX DGX-I-DXL Manual

14 September 2025

AMX DGX-O-HDMI Manual

14 September 2025

AMX EXB-MP1 Manual

14 September 2025

AMX DGX-I-DXF-SMD Manual

14 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vevor LX-PMMA-24*36 Manual

29 November 2025

Twelve South BookBook Manual

29 November 2025

Vevor SSH-1S-100-2 Manual

29 November 2025

Vevor GYZU-6T Manual

29 November 2025

Vevor H10263-57 Manual

29 November 2025

Vevor SP-HL-P202010-10A Manual

29 November 2025

Yamaha PLG150-DR Manual

29 November 2025

Extech 380460 Manual

29 November 2025

Blumfeldt Versagrow Manual

29 November 2025

Vevor EVS-15L Manual

29 November 2025