AMX MXD-700-NC Manual

AMX Ikke kategoriseret MXD-700-NC

Læs gratis den danske manual til AMX MXD-700-NC (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 105 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 53 anmeldelser. Har du et spørgsmål om AMX MXD-700-NC, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

QUICK START GUIDE

MXD-700 7" Modero X

Series Wall Mount Touch Panel

Overview

The MXD-700 7" Modero X Series

Wall Mount Touch Panel features edge-to-edge capacitive

touch glass with multi-touch capabilities as well as advanced technology empowering users to

operate AV equipment seamlessly, while providing the ultimate in audio and video quality. The

MXD-700 is available in Portrait and Landscape layouts:

Product Specifications

For a full listing of product specifications, refer to the X-Series Touch Panels MXD/T-1000,

MXD/T-700 & MXD-430 Instruction Manual (available to view/download from www.amx.com).

Note: The MXD-700-P-NC (FG5968-28) and MXD-700-L-NC (FG5968-29) No Comm touch

panels do not have microphone capability. These otherwise have all of the functionality of the

MXD-700 panels.

MXD-700 Installation

• For more detailed installation instructions including important notes on thermal

concerns with Rack and Wall installations, refer to the X-Series Touch Panels MXD/

T-1000, MXD/T-700 & MXD-430 Instruction Manual (available to view/download from

www.amx.com).

• Detailed specifications drawings for the MXD-700 are available to download from

www.amx.com.

The MXD-700 may be installed directly into a solid surface environment, using either solid

surface screws or the included locking tabs for different mounting options.

Once installed, the MXD-700 is contained within a clear outer housing known as the Backbox

(FIG. 2). The Backbox is removed to install it into a wall, or when using the optional Rough-In

Box accessory (FG039-18).

Note: For typical mounting surfaces, such as drywall, use the locking tabs as the primary

method for securing the Backbox to the surface. For thin walls or solid surfaces, use mounting

screws (not included).

Power Via PoE

Power for the MXD-700 is supplied via PoE (Power Over Ethernet), utilizing an AMX-certified,

capacitive touch-compliant PoE injector or other approved AMX PoE power source. The

incoming Ethernet cable should be connected to the RJ45 port on the MXD-700.

Installing the MXD-700 Into a Wall

The MXD-700 comes with a clear plastic Backbox (designed to attach the panel to most

standard wall materials. This Backbox has two locking tabs (one on top and one on bottom) to

help lock the Backbox to the wall. These locking tabs are only extended AFTER the Backbox is

inserted into the wall (FIG. 3).

• When installing the Backbox, make sure that the assembly is in the correct position and

in the correct place. Once the locking tabs are extended and locked into place, removing

the Backbox may be difficult without having access to the back of the wall or causing

damage to the wall.

• In order to ensure a stable installation of the MXD-700, the thickness of the wall

material must be a minimum of .50 inches (1.27cm) and a maximum of .875 inches

(2.22cm). The mounting surface should also be smooth and flat.

Installing the Backbox

For best results, use the included Installation Template (68-5968-04) to ensure proper

placement. The template is marked on one side with directions for both landscape and portrait

installations to ensure that the touch panel and Backbox are properly aligned.

WARNING: Using the Installation Template to select the final placement of the Backbox is highly

recommended. The outside edges of the template are the same dimensions as the touch panel,

which allows you to troubleshoot possible conflicts with wall edges, doors, and other potential

obstacles.

1. Prepare the area by removing any screws or nails from the drywall before beginning the

cutout process.

2. After ensuring proper placement, cut out the mounting surface for the Backbox, using

the (included) Installation Template as a guide.

CAUTION: Making sure the actual cutout opening is slightly smaller than the provided

dimensions is highly recommended. This provides a margin of error if the opening needs to

be expanded. Too little wall material removed is always better than too much.

3. Thread the incoming Ethernet cable through the surface opening (FIG. 4).

Leave enough slack in the wiring to accommodate any re-positioning of the panel.

4. Remove the Backbox knockouts and thread the incoming wiring through the knockout

holes.

5. Thread the incoming cables from the mounting surface opening and through the

knockouts.

6. Push the Backbox into the mounting surface. Insure that the locking tabs lie flush

against the Backbox and that the Backbox goes freely into the opening.

7. Extend the locking tabs on the sides of the Backbox by tightening the screws inside the

box until snug. Apply enough pressure to the screw head to keep the box flush with the

wall: this ensures that the locking tabs will tighten up against the inside of the wall. The

Backbox is clear to allow visual confirmation that the tabs have been extended and are

gripping the wall, as well as in assisting with removal if necessary.

Note: The maximum recommended torque to screw in the locking tabs on the Backbox is 5

IN-LB [56 N-CM]. Applying excessive torque while tightening the tab screws, such as with

powered screwdrivers, can strip out the locking tabs or damage the Backbox.

8. For additional strength, #4 mounting screws (not included) may be secured via

mounting holes located at the left and right sides of the MXD-700 (FIG. 4). In order to

prevent damage to the touch panel, make sure that these are flush with the Backbox.

Portrait MXD-700-P FG5968-08

Landscape MXD-700-L FG5968-14

FIG. 1 MXD-700-P/L WALL MOUNT (PORTRAIT AND LANDSCAPE)

MXD-700 SPECIF ICATIONS

Dimensions (HWD) • Landscape: 4 13/16" x 7 5/16" x 2 1/2" (122mm x 186mm x 63mm)

• Portrait: 7 5/16" x 4 13/16" x 2 1/2" (186mm x 122mm x 63mm)

Weight 1.4 lbs (0.64 Kg)

Power Consumption • Full-On: 8W

• Standby: 3.2W

• Shutdown: 1W

• Start-Up Inrush Current: Not applicable due to PoE standard

External Power

Supply Required

Optimal performance requires use of one of the following AMX PoE power

supplies (not included):

• PS-POE-AF-TC, PoE Injector, 802.3AF Compliant (FG423-83)

• NXA-ENET8-2POE, Gigabit PoE Ethernet Switch (FG2178-63)

Certifications • UL 60950-1

• FCC Part 15 Class B

• C-Tick CISPR 22 Class B

• CE EN 55022, EN 55024 and EN 60950-1

• IEC 60950-1

•IC

• IEC/EN-60950

• RoHS/WEEE compliant

Environmental • Temperature (Operating): 32° F to 104° F (0°C to 40°C)

• Temperature (Storage): 4° F to 140° F (-20°C to 60°C)

• Humidity (Operating): 20% to 85% RH

• Humidity (Storage): 5% to 85% RH

• Power ("Heat") Dissipation:

On: 18.5 BTU/hr

Standby: 10.6 BTU/hr

Included

Accessories

• MXA-USB-C, USB Port Cover Kit (FG5968-18)

• MXA-CLK, Modero X/S Series Cleaning Kit (FG5968-16)

• MXD-700 Installation Template

Sleep ButtonNFC Sensor

Sleep

NFC

Button

MXD-700-L

MXD-700-P

Sensor

FIG. 2 MXD-700 BACKBOX (REAR VIEW)

FIG. 3 MXD-700 (LANDSCAPE)

Locking tab

RJ45 cable clip

RJ45 Cable/Port

Backbox

Backbox knockouts (X4)

Locking tabs (X2)

Produkt Specifikationer

Mærke:	AMX
Kategori:	Ikke kategoriseret
Model:	MXD-700-NC

Har du brug for hjælp?

Hvis du har brug for hjælp til AMX MXD-700-NC stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret AMX Manualer

AMX NMX-DEC-N1233A Manual

26 November 2025

AMX DGX-O-DXF-MMS Manual

14 September 2025

AMX DVX-2250HD Manual

14 September 2025

AMX Vision² Manual

14 September 2025

AMX NMX-ENC-1100 Manual

14 September 2025

AMX UPC20+ Manual

14 September 2025

AMX DGX-I-DXL Manual

14 September 2025

AMX DGX-O-HDMI Manual

14 September 2025

AMX EXB-MP1 Manual

14 September 2025

AMX DGX-I-DXF-SMD Manual

14 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vevor LX-PMMA-24*36 Manual

29 November 2025

Twelve South BookBook Manual

29 November 2025

Vevor SSH-1S-100-2 Manual

29 November 2025

Vevor GYZU-6T Manual

29 November 2025

Vevor H10263-57 Manual

29 November 2025

Vevor SP-HL-P202010-10A Manual

29 November 2025

Yamaha PLG150-DR Manual

29 November 2025

Extech 380460 Manual

29 November 2025

Blumfeldt Versagrow Manual

29 November 2025

Vevor EVS-15L Manual

29 November 2025