Black And Decker Q210 Manual

Black And Decker bore Q210

Læs gratis den danske manual til Black And Decker Q210 (6 sider) i kategorien bore. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Black And Decker Q210, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/6
General Safety Rules
WARNING: Read and understand all instructions. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids,
gases, or dust. Power tools create sparks which may ignite the dust or fumes.
Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you
to lose control.
LECTRICAL SAFETY
Double insulated tools are equipped with a polarized plug (one blade is wider than the other.) This
plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the
plug in any way. Double insulation eliminates the need for the three wire grounded power cord and
d d l
TOOL USE AND CARE
•Use clamps or other practical way to secure and suppo
the work by hand or against your body is unstable and m
•Do not force tool. Use the correct tool for your applicatio
safer at the rate for which it is designed.
•Do not use tool if switch does not turn it on or off. Any to
dangerous and must be repaired.
•Disconnect the plug from the power source before maki
storing the tool. Such preventative safety measures reduc
•Store idle tools out of reach of children and other untrai
of untrained users.
•Maintain tools with care. Keep cutting tools sharp and c
cutting edges are less likely to bind and are easier to con
•Check for misalignment or binding of moving parts, bre
may affect the tools operation. If damaged, have the to
caused by poorly maintained tools.
•Use only accessories that are recommended by the man
be suitable for one tool, may become hazardous when us
SERVICE
•Tool service must be performed only by qualified repair
by unqualified personnel could result in a risk of injury.
•When servicing a tool, use only identical replacement p
section of this manual. Use of unauthorized parts or failu
create a risk of electric shock or injury.
SPECIFIC SAFETY RULES
•Hold tool by insulated gripping surfaces when performin
contact hidden wiring or its own cord. Contact with a "liv
tool "live" and shock the operator.
The label on your tool may include the following sym
V ..........................volts
Hz ........................hertz
min ......................minutes
....................direct current
........................
Class II Construction
........................safety alert symbol
Q210
INSTRUCTION MANUAL
3/8" (10MM) 5.0 AMP
KEYLESS CHUCK DRILL
INFORMATION YOU SHOULD KNOW
• Hand tighten keyless chuck firmly after each bit change.
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
SAVE THIS MANUAL FOR FUTURE REFERERENCE.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL
PRODUCTO.
AT. NO. Q210 FORM NO. 386868 (JAN98 CD-1) COPYRIGHT 1998 PRINTED IN USA
Fig. 3B
BUBBLE
BULLE
Fig. 1 Fig. 2
REVERSING LEVER
INVERSEUR DE MARCHE
"A"
9. With variable speed drills there is no need to center punch the point to be drilled. Use a slow speed
o start the hole and accelerate by squeezing the trigger harder when the hole is deep enough to drill
without the bit skipping out.
DRILLING IN METAL
se a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry. The
utting lubricants that work best are sulphurized cutting oil or lard oil; bacon-grease will also serve the purpose.
OTE: Large (5/16" to 3/8") (7.9mm to 9.5mm) holes in steel can be made easier if a pilot hole (5/32" to 3/16")
3.9mm to 4.8mm) is drilled first.
DRILLING IN WOOD
oles in wood can be made with the same twist drills used for metal. These bits may overheat unless pulled out
equently to clear chips from the flutes. For larger holes, use power drill wood bits. Work that is apt to splinter
hould be backed up with a block of wood.
DRILLING IN MASONRY
se carbide-tipped masonry bits at low speeds. Keep even force on the drill but not so much that you crack the
rittle materials. A smooth, even flow of dust indicates the proper drilling rate.
BUILT-IN 2-WAY LEVEL
our drill is equipped with a 2-way bubble level that assists you in drilling level holes. For horizontal drilling, tilt the
rill up or down as required so the bubble floats in the center of the parallel lines drawn on the glass. When the
ubble is centered between the lines, as shown in Figure 3A, the drill is level. For vertical drilling, align the drill so
at the bubble in the level floats in the center of the bull’s-eye, as shown in Figure 3B. To assure accuracy, first place
level on your workpiece and position it so that it is level. Then, when the drill reads level, the two will be aligned.
Any bubble level can only indicate level relative to the earth.)
OTE: The level is filled with mineral oil that may cause minor skin or eye irritation when contacted. If the level
reaks and this fluid gets on your skin, rinse thoroughly with water. If any liquid gets in your eyes, rinse thoroughly
ith water and call a physician immediately.
KEYLESS CHUCK
our tool features a keyless chuck for greater convenience. To insert a drill bit or other accessory, follow the steps
sted below.
1. TURN OFF AND UNPLUG. Make sure that the lock-on button is released.
2. Grasp the rear half of the chuck with one hand and use your other hand to rotate the front half in the direction
marked RELEASE on the nose of the chuck, as shown in Figure 4. Rotate far enough so that the chuck opens
ufficiently to accept the desired accessory.
3. Insert the bit or other accessory about 3/4" (19mm) into the chuck and tighten securely by holding the rear
alf of the chuck and rotating the front portion in the GRIP direction. To release the accessory, repeat step 2 listed
bove.
WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the front part of the chuck
nd turning the tool on. Damage to the chuck and personal injury may result. Always unplug unit and turn off
witch when changing accessories.
CHUCK REMOVAL
ace hex key in chuck as shown in Figure 5. Using a wooden mallet or similar object, strike key sharply in the
ELEASE direction. This will loosen the chuck so that it can be unscrewed by hand.
CHUCK INSTALLATION
crew the chuck on by hand as far as it will go. Tighten the chuck around the shorter end of a 1/4" (6.4mm) or
rger hex key (not supplied) strike the longer end in the GRIP direction with a soft hammer, as shown in Figure 6.
UBRICATION
our new drill uses self lubricating bearings and gears. Periodic relubrication is not required.
PROJECT TIPS
1. When drilling into metal, use a Bullet® Pilot® point drill bit to achieve a fast, clean hole without the bit
walking on the surface at start up.
2. For accurate horizontal and vertical drilling, use the built in level.
3. When using corded drills like the Q210, use the shortest practical extension cord or none at all.
Extension cords rob your drill of power and the longer they are, the more power they consume.
4. When driving screws into drywall, avoid driving them so deep that they tear the paper.
5. When driving screws in wood, pre-drill pilot holes to avoid splitting the wood.
Maintenance
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be
performed by authorized service centers or other qualified service organizations, always using identical
replacement parts.
Accessories
Recommended accessories for use with your tool are available from your local dealer or authorized service
center. If you need assistance regarding accessories, please call: 1-800-54-HOW TO.
WARNING: The use of any accessory not recommended for use with this tool could be hazardous.
For safety in use, the following accessories should be used only in sizes up to the maximum
shown in the table below. We recommend that your first purchase be safety glasses which
should be used with all accessories.
MAXIMUM RECOMMENDED CAPACITIES
DRILL CAPACITY 3/8" (10mm)
R.P.M. 0–2,500
BITS, METAL DRILLING 3/8" (10mm)
WOOD, FLAT BORING 1" (25.4mm)
BITS, MASONRY DRILLING 1/2" (12.7mm)
ACCESSORY MUST BE RATED FOR USE AT SPEED EQUAL TO OR HIGHER THAN NAMEPLATE R.P.M. OF
TOOL WITH WHICH IT IS BEING USED.
WIRE WHEEL BRUSHES 4" (101.6mm) Diameter Maximum
WIRE CUP BRUSHES 3" (76 2mm) Diameter Maximum
RENSEIGNEMENTS
•Bien serrer à la main le mandrin sans clé aprè
CONSERVER LE PRÉSENT GUID
Mesures de sécurité
AVERTISSEMENT! Lire et comprendre toutes les dir
suivantes présente des risques de
blessures graves.
CONSERVER CES
ZONE DE TRAVAIL
•S'assurer que la zone de travail est propre et bien éclair
sombres présentent des risques d'accidents.
•Ne pas utiliser des outils électriques en présence de vape
des liquides, des gaz ou des poussières inflammables).
électriques peuvent enflammer les poussières ou les vapeu
• Éloigner les curieux, les enfants et les visiteurs de la zone
Une distraction peut entraîner la perte de maîtrise de l'out
MESURES DE SÉCURITÉ RELATIVES À L'ÉLECTRICITÉ
•Les outils à double isolation comportent une fiche polaris
n'entre que d'une façon dans une prise polarisée. Lorsq
essayer de nouveau après avoir inversé les broches de l
prise, communiquer avec un électricien certifié afin de fa
en aucune façon la fiche. La double isolation élimine
d'un système d'alimentation mis à la terre.
• Éviter de toucher à des surfaces mises à la terre comme
des réfrigérateurs. Les risques de secousses électriques so
la terre.
• Protéger les outils électriques de la pluie ou des conditio
augmente les risques de secousses électriques.
•Manipuler le cordon avec soin. Ne jamais se servir du c
cordon pour débrancher l'outil. Éloigner le cordon des s
arêtes tranchantes et des pièces mobiles. Remplacer im
cordons endommagés augmentent les risques de secousse
•Lorsqu'on utilise un outil électrique à l'extérieur, se servi
l'extérieur, portant la mention «W-A» ou «W». Ces cord
minimisent les risques de secousses électriques. Lorsqu’on
est de calibre approprié pour la tension nécessaire au fon
de calibre inférieur occasionne une baisse de tension entr
Le tableau suivant indique le calibre approprié selon la lo
signalétique de l’outil. En cas de doute, utiliser un cordon
calibre est inversement proportionnel au calibre du cordo
FRANÇ
Q210
PERCEUSE DE 10 M
ET DE 5 A À MANDR
GUIDE D'UTI
AVANT DE RETOURNER LE P
LA RAISON PRIÈRE D
1 800 544
Calibre minimal des cord
Tension Longueur totale
120 V De 0 à 25 De 26 à 50
240 V De 0 à 50 De 51à 100
Intensité (A)
Au Au Calibre
moins plus
0 - 6 18 16
6 - 10 18 16

Produkt Specifikationer

Mærke: Black And Decker
Kategori: bore
Model: Q210

Har du brug for hjælp?

Hvis du har brug for hjælp til Black And Decker Q210 stil et spørgsmål nedenfor, og andre brugere vil svare dig


bore Black And Decker Manualer

Black And Decker

Black And Decker XD1200 Manual

4 Oktober 2024
Black And Decker

Black And Decker PS3500 Manual

20 September 2024
Black And Decker

Black And Decker CD18SR Manual

14 September 2024
Black And Decker

Black And Decker 9049 Manual

13 September 2024
Black And Decker

Black And Decker HP1800 Manual

13 September 2024
Black And Decker

Black And Decker CD431 Manual

10 September 2024
Black And Decker

Black And Decker TP550 Manual

6 September 2024
Black And Decker

Black And Decker TP555 Manual

6 September 2024
Black And Decker

Black And Decker BEH850 Manual

3 September 2024
Black And Decker

Black And Decker LDX172 Manual

27 August 2024

bore Manualer

Nyeste bore Manualer

Einhell

Einhell BM-G1100 E Manual

14 Oktober 2024
Sun Joe

Sun Joe 24V-DDK-LTX-PNK Manual

14 Oktober 2024
DeWalt

DeWalt DWD450 Manual

14 Oktober 2024
Rupes

Rupes BH 252R Manual

13 Oktober 2024
Makita

Makita DHR263ZJ Manual

12 Oktober 2024
Makita

Makita HP2070 Manual

12 Oktober 2024
Makita

Makita DDA350RFJ Manual

7 Oktober 2024
Einhell

Einhell TE-ID 750/1 E Manual

7 Oktober 2024
Makita

Makita HP332D Manual

7 Oktober 2024
Makita

Makita M6501 Manual

6 Oktober 2024