Brother PT-P700 Manual

Brother Etiketprinter PT-P700

Læs gratis den danske manual til Brother PT-P700 (4 sider) i kategorien Etiketprinter. Denne vejledning er vurderet som hjælpsom af 34 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 17.5 anmeldelser. Har du et spørgsmål om Brother PT-P700, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Follow these guidelines to avoid the risk of fire, burns,

injury, electric

shocks, rupture, overheating, abnormal odors or smoke.

• Always use the specified voltage and the included AC adapter (AD-E001) for the

P-touch labeler to prevent any damage or failure.

• Do not touch the P-touch labeler during a lightning storm.

• Do not use the P-touch labeler/AC adapter in places of high humidity such as

bathrooms.

• Do not overload the power cord.

• Do not place heavy objects on, or damage the P-touch labeler, power cord or plug.

Do not forcibly bend or pull the power cord. Always hold the AC adapter when

disconnecting from the power outlet.

• Make sure that the plug is fully inserted in the power outlet. Do not use an outlet that

is loose.

• Do not allow the P-touch labeler/AC adapter/power plug/batteries to get wet, for

example, by handling them with wet hands or spilling beverages on to them.

• Do not disassemble or modify the P-touch labeler/AC adapter/batteries.

• Do not allow a metal object to contact both the plus and minus ends of a battery.

• Do not use sharp objects, such as tweezers or a metallic pen, to change the

batteries.

• Do not throw the batteries into fire or expose to heat.

• Disconnect the AC adapter, remove batteries immediately and stop using the

P-touch labeler if you notice abnormal odor, heat, discoloration, deformation or

anything unusual while using or storing it.

• Do not use a damaged or leaking battery as the fluid may get on your hands.

• Do not use a deformed or leaking battery or one whose label is damaged. There is

a possibility of damaging the P-touch labeler.

• Since loss of eyesight may result when leaked fluid from batteries gets into your

eyes, immediately rinse your eyes with a large amount of clean water, and then

seek medical attention.

Follow these guidelines to avoid personal injury, liquid leakage, burns

or heat.

• When the P-touch labeler is not being used, store it out of the reach of children. In

addition, do not allow children to put any P-touch labeler parts or labels in their

mouths. If any object has been swallowed, seek medical attention.

• Do not touch metal parts around the print head immediately after printing.

• Do not touch the cutter blade. (See Parts Description.)

• If leaked fluid from batteries gets on your skin or clothes, immediately rinse them

with clean water.

• Remove the batteries and disconnect the AC adapter if you do not intend to use the

P-touch labeler.

• Do not use any batteries other than those specified. Do not

use combinations of old

and new batteries or combinations of different types, different charging levels,

different manufacturers or different models. Do not insert a battery with its plus and

minus ends reversed.

• Do not drop or hit the P-touch labeler/AC adapter.

• Do not put your finger inside the P-touch labeler when you close the cassette cover.

• Before using Ni-MH rechargeable batteries, carefully read the instructions for the

batteries and battery charger, and be sure to use them correctly.

• When using Ni-MH rechargeable batteries, charge the batteries with a specialized

battery charger before using the batteries.

• Depending on the location, material, and environmental conditions, the label may

unpeel or become irremovable, the color of the label may change or be transferred

to other objects. Before applying the label, check the environmental conditions and

the material.

• Do not use the P-touch labeler in any way or for any purpose not described in this

guide. Doing so may result in accidents or damage to the P-touch labeler.

• Use only Brother TZe tapes with the P-touch labeler. Do not use tapes that do not

have the mark.

• Only use a soft, dry cloth to clean the P-touch labeler; never use alcohol or other

organic solvents.

• Use a soft wipe to clean the print head; never touch the print head with your fingers.

• Do not put any foreign objects into the tape exit slot or AC adapter connector or

battery compartment, etc.

• Do not place the P-touch labeler/batteries/AC adapter in direct sunlight or rain, near

heaters or other hot appliances, in any location exposed to extremely high or low

temperatures (e.g., on the dashboard or in the back of your car) or high humidity, or

in dusty locations.

• Do not try to print if the cassette is empty; it will damage the print head.

• Do not pull the tape while printing or feeding; it will damage the tape and the P-touch

labeler.

• Any data stored in memory will be lost due to failure or repair of the P-touch labeler,

or if the batteries expire.

• The P-touch labeler is not equipped with a charging feature for rechargeable

batteries.

• The length of the printed label may differ from the displayed label length on the

computer.

• A protective clear plastic sticker is placed over the top panel during manufacturing

and shipping. This sticker should be removed prior to use.

• When printing multiple copies of a label or using the numbering function printing, the

P-touch labeler will not detect the end of the tape cassette and will continue

operating.

• When using Heat Shrink Tube, the printing area will be smaller than when using

normal tape.

• Do not scratch or subject the CD-ROM to high or low temperatures.

• Do not put heavy objects on the CD-ROM or apply force to the CD-ROM.

• The software contained on the CD-ROM is meant for use with this P-touch labeler only.

See the License on the CD-ROM for details. This software may be installed on

multiple computers for use in an office, etc.

The purpose of the International ENERGY STAR® Program is

to promote the development and popularization of

energy-efficient office equipment. As an ENERGY STAR

Partner, Brother Industries, Ltd. has determined that this

product meets the ENERGY STAR® guidelines for energy

efficiency.

Should you have questions, or need information about your Brother product, we have

a variety of support options for you to choose from:

USA-Customer Service

Telephone: 1-877-BROTHER (1-877-276-8437)

Fax: 1-901-379-1210

Website: www.brother-usa.com

Supplies/Accessories:

www.brothermall.com or 877-552-6255

Safety Precautions

WARNING Indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injuries.

CAUTION Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injuries.

ELECTRONIC LABELING SYSTEM

Thank you for choosing the PT-P700. Your new P-touch labeler uses P-touch Editor Lite software,

which is already installed on your P-touch labeler.

There is no need to install any software or drivers onto your computer in order to make creative labels.

This manual includes important precautionary information and simple instructions for operating your

new P-touch labeler. Be sure to read the instructions before use and use the product in accordance

with these instructions. Keep this manual handy for future reference. If new versions of the PT-P700

software become available, this manual may not reflect the updated features. Therefore, you may find

that the software and the contents in this guide are different.

Printed in China

LAD095001

English

Español

PT-P700

User’s Guide

General Precautions

Federal Communications Commission (FCC) Declaration of

Conformity (For USA Only)

Responsible Party : Brother International Corporation

200 Crossing Boulevard

P.O. Box 6911

Bridgewater, NJ 08807-0911 USA

TEL : (908) 704-1700

declares that the products

Product Name : Brother P-touch Electronic Labeling System

Model Number : PT-P700

comply with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Important

• The enclosed interface cable should be used in order to ensure compliance with

the limits for a Class B digital device.

• Changes or modifications not expressly approved by Brother Industries, Ltd.

could void the user’s authority to operate the equipment.

International ENERGY STAR® Compliance

Statement

Important Information

Unpacking the PT-P700

Check that the package contains the following before using the P-touch labeler. If any item is

missing or damaged, contact your Brother reseller.

Parts Description

Setting the Tape Cassette

1. Place the P-touch labeler so that the cassette cover is

facing upwards, then open the cassette cover.

2. Insert a tape cassette and close the cassette cover.

Restore the P-touch labeler to an upright position.

Connecting the Power Supply

Using the AC adapter

When using the included AC adapter (AD-E001), insert the

plug on the adapter cord into the AC adapter connector of

the P-touch labeler. Insert the plug into the nearest

standard electrical outlet.

Using the batteries

When using the P-touch labeler with batteries, open the

battery cover on the bottom of the P-touch labeler, insert six

"AA" alkaline batteries (LR6) or Ni-MH rechargeable

batteries (HR6), making sure that their poles point in the

correct directions, and then close the battery cover. Always

replace all six batteries at the same time using new

batteries or fully charged rechargeable batteries.

Creating a Label using P-touch Editor

Lite

1. Turn on the P-touch labeler, then press and hold

down the Editor Lite button until the green Editor Lite

lamp lights up.

2. Connect the USB cable to the computer.

3. After the USB cable is connected, a dialog box appears on the computer display. (The

following screens may differ depending on the operating system on your computer.)

For Windows Vista®

Click [P-touch Editor Lite].

For Windows® 7

Click [Open folder to view files], and then double-click [PTLITE10].

For Windows® 8

On the [Start] screen, click [PT-P700], [Open folder to view files], and then double-click

[PTLITE10].

For Mac OS X v10.6.8 - v10.8.x

Double-click [PT-P700] on the desktop and the [ ] application icon.P-touch Editor Lite

4. P-touch Editor Lite starts. For details on using P-touch Editor Lite, see the Software User’s

Guide included on the CD-ROM (for Windows

®) or download the Software User’s Guide by

visiting the Brother Solutions Center at http://solutions.brother.com/ (for Macintosh).

Macintosh users can access this URL directly by clicking the icon found in CD-ROM.

• PT-P700 • AC adapter (AD-E001) • USB cable

• CD-ROM • User's Guide • Starter tape cassette

1 Top panel

2 Editor Lite lamp

3 Editor Lite button

4 Tape exit slot

5 Feed & Cut button

6 Status lamp

7 Power button

8 Battery cover

9 Mini-USB port

10 AC adapter connector

11 Cassette cover

12 Release lever

13 Print head

14 Tape cutter

15 Cutter blade

CAUTION

Do not put your finger inside the tape exit slot. You

could be injured by the cutter blade.

911

NOTE

If you are connecting the P-touch labeler via a USB

hub, it may not be detected correctly.

NOTE

• If you do not see the dialog box, it may be hidden behind an open software program

window. Minimize all windows to show the dialog box.

• (For Windows®)

It will take longer than usual to start P-touch Editor Lite when connecting the P-touch

labeler to your computer for the first time. If the software does not start automatically

when you connect the P-touch labeler, you may launch it from [My Computer]. Start P-

touch Editor Lite by double-clicking [PTLITE10.EXE].

• (For Windows Vista®)

When connecting the device for the first time, perform the scan and then select the

[Always do this for software and games] check box on the dialog box displayed when

the scan finishes. P-touch Editor Lite will start automatically the next time you connect

the P-touch labeler.

(For Windows®)(For Macintosh)

IMPORTANT

Do not turn off the power or disconnect the P-touch labeler while using P-touch Editor Lite.

Produkt Specifikationer

Mærke:	Brother
Kategori:	Etiketprinter
Model:	PT-P700
Bredde:	78 mm
Dybde:	152 mm
Højde:	143 mm
Vægt:	710 g
Produktfarve:	Black,White
Wi-Fi:	Ingen
USB-port:	Ja
Antal USB 2.0-porte:	1
Ethernet LAN:	Ingen
Automatisk slukning:	Ja
Maksimal opløsning:	180 x 180 dpi
Skærm:	Ingen
Hurtig start guide:	Ja
Kabler inkluderet:	USB
Understøttede billedformater:	BMP,JPG,TIF
Forbindelsesteknologi:	Ledningsført
AC-adapter inkluderet:	Ja
Harmoniseret systemkode (HS):	84433210
Antal understøttede batterier:	6
Tekstlinjer:	3 Linier
Understøttede Mac-operativsystemer:	Mac OS X 10.6 Snow Leopard,Mac OS X 10.7 Lion,Mac OS X 10.8 Mountain Lion
Udskrivningshastighed:	30 mm/sek.
Vertikal udskrivning:	Ja
PC tilsluttet:	Ja
Maksimal udskrivningsbredde:	24 mm
Maksimal etiketbredde:	24 mm
Maksimal etiketlængde:	1 m
Vis antal af karakterer:	16
Maksimal udskrivningshøjde:	18 mm
Antal etiketformater:	8
Indbyggede stregkoder:	AZTECCODE,CODABAR (NW-7),Code 39,Data Matrix,EAN128,EAN13,EAN8,GS1 COMPOSITE,GS1 DataBar,GS1-128,ISBN-2,ISBN-5,ITF,MaxiCode,Micro QR Code,PDF417,POSTNET,QR Code,UPC-A,UPC-E
Antal skrifttyper:	14
Auto-skærer:	Ja
Antal stilarter:	11
Tape skæring:	Automatisk
Vis udskrift:	Ja
Båndtype:	TZe
Print, maksimale antal linier:	7
Antal rammer:	154