Candy cce 16 Manual

Candy Emhætte cce 16

Læs gratis den danske manual til Candy cce 16 (16 sider) i kategorien Emhætte. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Candy cce 16, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/16

INSTRUCTIONS FOR INSTALLATION AND USE

MONTAGE- UND GEBRAUCHSANWEISUNG

INSTRUCTIONS POUR L'INSTALLATION ET L’UTILISATION

ISTRUZIONI PER L'INSTALLAZIONE E L’USO

INSTRUCCIONES PARA INSTALACIÓN Y USO

AANWIJZING VOOR GEBRUIK EN INSTALLATIE

ENGLISH

DESCRIPTION

The unit can be found in filtering hoods or in exhaust hoods. In the Filtering hoods (Fig. 1) the air and steam

taken up by the unit are purified with charcoal filters and returned to the environment through the aeration grids on

the side of the flue. WARNING: When using filtering hoods, both charcoal filters and an air deflector (A) must be

used. Located in the lower part of the flue, this deflector recycles the air to the environment. The charcoal filters are

not supplied. In the Exhaust hoods (Fig .2) an exhaust duct conveys the steam and cooking odors directly outside

through the wall/ceiling. Therefore they do not require charcoal filters.

INSTALLATION

To facilitate installation, before starting remove the grease filters: press inward on the clamp at the handle and

pull the filter downward (Fig. 3).

Wall fitting (Fig. 4): making use of the appropriate drilling jig, apply the supplied blocks into the wall, and

remember the distance between the hood and the cooktop must be at least 65 cm. Insert two of the supplied screws

so that the apparatus can be hooked onto these ones by means of the holes provided on the appliance (A). Once

the apparatus is hooked, fix it definitively to the wall using the two other screws and the holes made at its bottom

(B). To avoid damage make exclusive use of the holes already prepared on the hood.

Securing the telescopic flue: Basic installation requirements: – Set the electrical power supply within the space

covered by the decorative flue. – If your unit is installed in an Exhaust hood, prepare the air exhaust hole.

Place bracket (W) 50 mm from the ceiling and position this on the vertical of your hood, with the aid of the notches

on the centre of the bracket (Fig. 5); using a pen, mark the 2 holes on the wall and then make the holes and fit the

screw anchors provided and proceed to secure the bracket using the 2 screws (provided).

Exhaust hoods: connect the disposal duct to the air evacuation pipe of the hood; use a flexible pipe and lock it to

the air evacuation pipe of the hood with a metal hose clamp (pipe and clamp are not provided). Make all power

connections to the hood by means of the power cable. Take 2 assembled flues and place these on the upper surface

of the hood. Raise the upper flue as far as the ceiling and secure it to the bracket using the 2 screws (Fig. 6).

Filtering hood: make all power connections to the hood using the power cable. Fasten the air baffle to the lower flue

as shown in Figure 7, using the 2 screws. Take 2 assembled flues and place these on the upper surface of the hood.

Raise the upper flue as far as the ceiling and secure it to the bracket using the 2 screws (Fig. 6).

Also remember that charcoal filters must be used in the case of the filtering version; check to see whether such filters

are already fitted; if necessary, proceed to fit as follows, depending on the model type purchased:

- if the hood features round charcoal filters (Fig. 8), fit the charcoal filter by turning anti-clockwise.

- if the hood features a panel type charcoal filter (Fig. 9), remove the two metal filter retainers (M) and position the

charcoal filter inside the grease filter; fit the two filter retainers back on again to secure the charcoal filter.

OPERATION

Depending on the model, the unit is equipped with the following controls:

Controls shown in Fig. 10: Button A = light switch. Button B = first speed motor ON/OFF switch. Button C = second

speed switch. Button D = third speed switch. E = motor on light.

Controls shown in Fig. 11: A = Light switch; position 0: light off; position 1: light on. B = Motor switch; position

0: motor off; position 1-2-3: motor on at speed I, II and III. C = Motor pilot lamp.

Controls shown in Fig. 12: Button A = turns the lights on/off. Button B = turns the TIMER on/off: press once to

turn the timer on, therefore, after 5 minutes, the motor cuts out (at the same time the selected speed blinks on the

display); the timer remains on if the motor speed is changed. Display C = - indicates the selected motor speed (from

1 to 4); - indicates Timer On when the number blinks; - indicates Filter Alarm when the central segments is on or

blinking. Button D = makes the motor work (at the last speed selected); pushing the button again, the speeds of the

motor are sequentially selected from 1 to 4; keeping this button pressed for about 2 seconds shuts down the motor.

Button R = resets the grease filters or charcoal filters; when the filter alarm appears (i.e. when the central segment

on the display goes on), the grease filters must be cleaned (30 hours of operation); when the central segment starts

blinking, the grease filters must be cleaned and the charcoal filters replaced (120 hours of operation). Obviously,

if the hood is not a filtering model and does not have a charcoal filter, clean the grease filters both when the central

segment goes on and when it starts blinking. The filter alarm can be seen when the motor is off and for about 30

seconds. To reset the hour counter, keep the button pressed for 2 seconds while the alarm can be seen.

Controls shown in Fig. 13: Button A: turns the lights on/off; every 30 hours of operation the corresponding pilot lamp

(S) comes on to indicate that the grease filters must be cleaned; every 120 hours of operation the corresponding pilot

lamp (S) flashes to indicate that the grease filters must be cleaned and the charcoal filter replaced. To restart the hour

counter (RESET), hold the button A pressed down for about 1” (while the pilot lamp S is on). Button B: drives the

motor in first speed (the corresponding pilot lamp comes on); when holding it down for about 1”, the motor cuts out;

when pressing the button a second time (while the pilot lamp is on) , the TIMER is activated and thus the motor stops

after 5’ (the pilot lamp flashes). Button C: drives the motor in second speed (the corresponding pilot lamp comes on);

when pressing the button a second time (while the pilot lamp is on) , the TIMER is activated and thus the motor stops

after 5’ (the pilot lamp flashes). Button D: drives the motor in third speed (the corresponding pilot lamp comes on);

Produkt Specifikationer

Mærke:	Candy
Kategori:	Emhætte
Model:	cce 16

Har du brug for hjælp?

Hvis du har brug for hjælp til Candy cce 16 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Emhætte Candy Manualer

Candy CDG6CBP8W Manual

10 Juli 2025

Candy CDG6CBP8BWIFI Manual

9 Juli 2025

Candy CDG6CBP8B Manual

8 Juli 2025

Candy CDG7CBP8B Manual

8 Juli 2025

Candy CDG6CBBGG Manual

4 Juli 2025

Candy CDG9CBBGG Manual

30 Juni 2025

Candy CBT 63 X Manual

30 Juni 2025

Candy CDG6CBHT Manual

18 Juni 2025

Candy CFT610/4N-ALG Manual

17 Juni 2025

Candy CGM90NX Manual

1 Oktober 2024

Emhætte Manualer

Nyeste Emhætte Manualer

Haier HAPY72ES6XGG Manual

14 August 2025

Kenmore 92229 Manual

14 August 2025

Heinner HDCH-MD60TIX Manual

13 August 2025

Heinner HTCH-MD600GBK Manual

13 August 2025

Amica 9FH17162E Manual

13 August 2025

Kenmore 92222 Manual

13 August 2025

Amica 9FH664621E Manual

13 August 2025

Kenmore 92223 Manual

13 August 2025

Heinner CH-MD200WH Manual

13 August 2025

Heinner CH-MD190BK Manual

13 August 2025