Casio Collection SGW-1000-2BER Manual
Læs nedenfor 📖 manual på dansk for Casio Collection SGW-1000-2BER (12 sider) i kategorien Ur. Denne guide var nyttig for 24 personer og blev bedømt med 4.6 stjerner i gennemsnit af 12.5 brugere
Side 1/12
MO1503-EA © 2015 CASIO COMPUTER CO., LTD.
E-1
ENGLISH
Congratulations upon your selection of this CASIO watch.
Applications
The built-in sensors of this watch measure direction, barometric pressure, temperature and altitude.
Measured values are then shown on the display. Such features make this watch useful when hiking,
mountain climbing, or when engaging in other such outdoor activities.
Warning !
• The measurement functions built into this watch are not intended for taking measurements that
require professional or industrial precision. Values produced by this watch should be considered
as reasonable representations only.
•
When engaging in mountain climbing or other activities in which losing your way can create a
dangerous or life-threatening situation, always use a second compass to confi rm direction readings.
• Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage or loss
suffered by you or any third party arising through the use of this product or its malfunction.
E-2
Important!
• The watch’s Altimeter Mode calculates and displays relative altitude based on barometric pressure
readings produced by its pressure sensor. This means that readings taken at different times at the
same location may produce different altitude values due to changes in barometric pressure. Also note
that the value displayed by the watch may be different from the actual elevation and/or sea level
elevation indicated for the area where you are located.
• When using the altimeter of this watch for mountain climbing or other activities, it is highly
recommended that you check a map, local altitude indications, or some other source for your current
correct altitude and regularly calibrate the altimeter with the latest information. For more information,
see “To specify a reference altitude value” (page E-47).
• Whenever you use the digital compass of this watch for serious trekking, mountain climbing, or other
activities, be sure always to take along another compass to confi rm readings. If the readings produced
by the digital compass of this watch are different from those of the other compass, perform bidirectional
calibration of the digital compass to ensure more accurate readings.
• Direction readings and digital compass calibration will not be possible if the watch is in the vicinity of a
permanent magnet (magnetic accessory, etc.), metal objects, high-voltage wires, aerial wires, or
electrical household appliances (TV, computer, cellphone, etc.)
E-3
About This Manual
• Depending on the model of your watch, digital display text appears
either as dark fi gures on a light background, or light fi gures on a dark
background. All examples in this manual are shown using dark fi gures
on a light background.
• Button operations are indicated using the letters shown in the
illustration.
• Note that the product illustrations in this manual are intended for
reference only, and so the actual product may appear somewhat
different than depicted by an illustration.
E-4
Things to check before using the watch
1. Check the Home City and the daylight saving time (DST) setting.
Use the procedure under “To confi gure Home City and summer time settings” (page E-14) to confi gure
your Home City and daylight saving time settings.
Important!
• World Time Mode and Sunrise/Sunset Mode data depend on correct Home City, time, and date settings
in the Timekeeping Mode. Make sure you confi gure these settings correctly.
2. Set the current time.
See “Confi guring Current Time and Date Settings” (page E-16).
The watch is now ready for use.
E-5
Contents
About This Manual …………………………………………………………………………………………… E-3
Things to check before using the watch ………………………………………………………………… E-4
Mode Reference Guide ……………………………………………………………………………………… E-9
Timekeeping ………………………………………………………………………………………………… E-13
Confi guring Home City Settings ………………………………………………………………………… E-14
To confi gure Home City and summer time settings ……………………………………………… E-14
Confi guring Current Time and Date Settings ………………………………………………………… E-16
To change the current time and date settings …………………………………………………… E-16
Taking Direction Readings ……………………………………………………………………………… E-19
To take a direction reading ………………………………………………………………………… E-19
To perform bidirectional calibration ………………………………………………………………… E-23
To perform magnetic declination correction ……………………………………………………… E-24
To store a direction angle reading in Bearing Memory ………………………………………… E-25
Specifying Temperature, Barometric Pressure, and Altitude Display Units …………………… E-29
To specify temperature, barometric pressure, and altitude display units ……………………… E-29
Taking Barometric Pressure and Temperature Readings ………………………………………… E-31
To take barometric pressure and temperature readings ………………………………………… E-31
To enable or disable the barometric pressure change alert …………………………………… E-37
To calibrate the pressure sensor and the temperature sensor ………………………………… E-38
E-6
Using the Altimeter Mode ………………………………………………………………………………… E-40
To select the altitude screen format ……………………………………………………………… E-42
To select the altitude auto reading interval ……………………………………………………… E-43
To take altitude readings …………………………………………………………………………… E-45
To specify a reference altitude value ……………………………………………………………… E-47
To specify the altitude differential start point ……………………………………………………… E-48
To use the altitude differential value ……………………………………………………………… E-49
To save a reading manually ………………………………………………………………………… E-50
To start trek log value updating …………………………………………………………………… E-53
To stop trek log value updating …………………………………………………………………… E-53
Viewing Altitude Records ………………………………………………………………………………… E-58
To view altitude records …………………………………………………………………………… E-58
To delete all manually saved data ………………………………………………………………… E-62
To delete data in a specifi c memory area ………………………………………………………… E-62
Looking up Sunrise and Sunset Times ………………………………………………………………… E-64
To enter the Sunrise/Sunset Mode ………………………………………………………………… E-64
To view the sunrise/sunset time for a particular date …………………………………………… E-65
To look up the sunrise and sunset times for a specifi c location ………………………………… E-66
Using the Stopwatch ……………………………………………………………………………………… E-68
To enter the Stopwatch Mode ……………………………………………………………………… E-68
To perform an elapsed time operation …………………………………………………………… E-68
To pause at a split time ……………………………………………………………………………… E-68
To measure two fi nishes …………………………………………………………………………… E-69 E-7
Using the Countdown Timer ……………………………………………………………………………… E-70
To enter the Countdown Timer Mode ……………………………………………………………… E-70
To specify the countdown start time ……………………………………………………………… E-70
To perform a countdown timer operation ………………………………………………………… E-71
To stop the alarm …………………………………………………………………………………… E-71
Using the Alarm …………………………………………………………………………………………… E-72
To enter the Alarm Mode …………………………………………………………………………… E-72
To set an alarm time ………………………………………………………………………………… E-73
To turn an alarm and the Hourly Time Signal on and off………………………………………… E-74
To stop the alarm …………………………………………………………………………………… E-75
Checking the Current Time in a Different Time Zone ………………………………………………… E-76
To enter the World Time Mode …………………………………………………………………… E-76
To view the time in another time zone …………………………………………………………… E-76
To specify standard time or daylight saving time (DST) for a city ……………………………… E-77
Illumination ………………………………………………………………………………………………… E-78
To turn on illumination manually …………………………………………………………………… E-78
To change the illumination duration ……………………………………………………………… E-78
To turn the auto light switch on and off …………………………………………………………… E-80
Button Operation Tone …………………………………………………………………………………… E-82
To turn the button operation tone on and off ……………………………………………………… E-82
Operation Guide 3439
E-8
Low Battery Indication …………………………………………………………………………………… E-83
Troubleshooting …………………………………………………………………………………………… E-84
Specifi cations ……………………………………………………………………………………………… E-89
E-9
Mode Reference Guide
Your watch has 10 “modes”. The mode you should select depends on what you want to do.
To do this: Enter this mode: See:
• View the current date in the Home City
• Confi gure Home City and daylight saving time (DST) settings
• Confi gure time and date settings
Timekeeping Mode E-13
Determine your current bearing or the direction from your current location
to a destination Digital Compass Mode E-19
• View the barometric pressure and temperature at your current location
• View a graph of barometric pressure readings
Barometer/Thermometer
Mode E-31
• View the altitude at your current location
• Determine the altitude differential between two locations (reference
point and current location)
• Record an altitude reading with the reading time and date
Altimeter Mode E-40
View the sunrise and sunset times for a specifi c date Sunrise/Sunset Mode E-64
Recall records created in the Altimeter Mode Data Recall Mode E-58
Use the stopwatch to measure elapsed time Stopwatch Mode E-68
Use the countdown timer Countdown Timer Mode E-70
Set an alarm time Alarm Mode E-72
View the current time in one of 48 cities (31 time zones) around the globe World Time Mode E-76
E-10
Selecting a Mode
• The illustration below shows which buttons you need to press to navigate between modes.
• To return to the Timekeeping Mode from any other mode, hold down D for about two seconds.
Alarm Mode
Stopwatch Mode
World Time
Mode
Timekeeping Mode
Sunrise/Sunset
Mode
Data Recall
Mode
Countdown
Timer Mode Alarm Mode
Stopwatch Mode
World Time
Mode
Timekeeping Mode
Sunrise/Sunset
Mode
Data Recall
Mode
Countdown
Timer Mode
E-11
• You can use buttons A,B, and C to enter a sensor mode directly from the Timekeeping Mode or
from another sensor mode. To enter a sensor mode from the Sunrise/Sunset, Data Recall, Alarm,
Stopwatch, Countdown Timer or World Time, fi rst enter the Timekeeping Mode and then press the
applicable button.
Altimeter Mode
Barometer/
Thermometer ModeDigital Compass Mode
Sensor Modes
Altimeter Mode
Barometer/
Thermometer ModeDigital Compass Mode
Sensor Modes
E-12
General Functions (All Modes)
The functions and operations described in this section can be used in all of the modes.
Direct Timekeeping Mode Access
• To enter the Timekeeping Mode from any other mode, hold down
D for about two seconds.
Auto Return Features
• The watch will automatically return to the Timekeeping Mode if you do not perform any button operation
for a particular amount of time in each mode.
Mode Name Approximate Elapsed Time
Sunrise/Sunset, Data Recall, Alarm, Digital Compass 3 minutes
Altimeter 1 hour minimum
12 hours maximum
Barometer/Thermometer 1 hour
Setting screen (digital setting fl ashing) 3 minutes
• If you leave a screen with fl ashing digits on the display for two or three minutes without performing any
operation, the watch exits the setting screen automatically.
Initial Screens
When you enter the Data Recall, Alarm, World Time, or Digital Compass Mode, the data you were viewing
when you last exited the mode appears fi rst.
Scrolling
The A and C buttons are used on the setting screen to scroll through data on the display. In most
cases, holding down these buttons during a scroll operation scrolls through the data at high speed.
E-13
Timekeeping
Use the Timekeeping Mode (TIME) to set and view the current time and date.
• Each press of E in the Timekeeping Mode will change screen contents as shown below.
Day of the Week/Date Screen Month/Day Screen Barometric Pressure
Graph Screen
Barometric pressure graph
Day of week
Seconds
Hour :
Minutes
Day
PM
indicator
Month Day
E-14
Confi guring Home City Settings
There are two Home City settings: actually selecting the Home City and selecting either standard time or
daylight saving time (DST).
To confi gure Home City and summer time settings
1. In the Timekeeping Mode, hold down E for at least two seconds.
First, SET Hold will fl ash on the display, and CITY will be displayed in
the upper display. After that, the currently selected city code and city
name will scroll across the upper display. Keep E depressed until the
scrolling starts.
• The watch will exit the setting mode automatically if you do not
perform any operation for about two or three minutes.
• For details about city codes, see the “City Code Table” at the back
of this manual.
2. Use A (East) and C (West) to scroll through the available city codes.
• Keep scrolling until the city code you want to select as your Home
City is displayed.
3. Press D to display the DST setting screen.
4.
Press A to toggle the DST setting between Daylight Saving Time (
ON)
and standard time (
OFF ).
• Note that you cannot switch between standard time and daylight
saving time (DST) while UTC is selected as your Home City.
PM
indicator
City code
Hour :
Minutes
DST indicator
Seconds
PM
indicator
City code
Hour :
Minutes
DST indicator
Seconds E-15
5. After all of the settings are the way you want, press E twice to exit the setting screen.
• Daylight Saving Time is turned on when the indicator is on the display.DST
Note
• After you specify a city code, the watch will use UTC* offsets in the World Time Mode to calculate
the current time for other time zones based on the current time in your Home City.
* Coordinated Universal Time, the world-wide scientifi c standard of timekeeping.
The reference point for UTC is Greenwich, England.
Operation Guide 3439
Produkt Specifikationer
| Mærke: | Casio |
| Kategori: | Ur |
| Model: | Collection SGW-1000-2BER |
Har du brug for hjælp?
Hvis du har brug for hjælp til Casio Collection SGW-1000-2BER stil et spørgsmål nedenfor, og andre brugere vil svare dig
Ur Casio Manualer
7 April 2025
7 April 2025
30 Marts 2025
22 December 2024
22 December 2024
21 December 2024
21 December 2024
21 December 2024
21 December 2024
21 December 2024
Ur Manualer
- Ur Lucien Picard
- Ur Marc Jacobs
- Ur Prologue
- Ur Antelope
- Ur Fisher-Price
- Ur Gc
- Ur Lynx
- Ur Victorinox
- Ur Medion
- Ur Fysic
- Ur Nautica
- Ur Raketa
- Ur Profile
- Ur Boss
- Ur Focus Electrics
Nyeste Ur Manualer
9 Juni 2025
8 Juni 2025
8 Juni 2025
7 Juni 2025
7 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025