Casio PDM-10B Manual

Casio Ur PDM-10B

Læs gratis den danske manual til Casio PDM-10B (3 sider) i kategorien Ur. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Casio PDM-10B, eller vil du spørge andre brugere om produktet?

Side 1/3
1
Operation Guide PDM-10B/20B
MA0312-EA
ILLUSTRATION
PDM-10B
PDM-20B
A sticker is affixed to the glass of the pedometer when you purchase it. Be sure to remove the sticker before
using the pedometer.
Depending on the model of your pedometer, its configuration may differ somewhat from that shown in the
PDM-20B
55
55
5RESET button
Press to reset the number of steps to “0” .
66
66
6SET button
77
77
7MODE button
88
88
8Front panel
99
99
9Back panel
00
00
0Clip
AA
AA
ACursor
OPENING THE PEDOMETER PANELS (PDM-20B)
Holding the front and back panels of the pedometer, release the catch on the top of the panels and then open them
as shown in the illustration.
AFFIXING THE PEDOMETER TO YOUR CLOTHING
Clip the pedometer securely to your belt or the waistband of your slacks, skirt, training pants, etc.
Take care that you hook the clip so your belt or waistband enters the clip as far as it will go. Improper attachment
of the pedometer or wearing it an angle can cause mistakes in the number of step count.
Take care that you do not accidentally press the while you are attaching or removing theRESET button
pedometer. Accidentally pressing the will reset the number of steps to “0”.RESET button
Make sure that the two panels of the pedometer are securely closed while you are using it (PDM-20B).
GENERAL GUIDE
PDM-10B
11
11
1RESET button
Press to reset the number of steps to “0” .
Pressing this button while the display is blank turns
on the display.
Holding down this button turns off power.
22
22
2Front cover
33
33
3Back cover
44
44
4Clip
2
Operation Guide PDM-10B/20B
HOW THE PEDOMETER WORKS
This pedometer is intended for use while walking during normal daily life and during light jogging.
As you walk or jog across a level surface, the pedometer detects the impact acceleration generated when your
foot hits the ground.
If you hold the pedometer vertically and shake it up and down, you should be able to hear a rattling sound. This
is the sound of the pendulum inside the pedometer that is used for detecting movement. This sound indicates
that the pedometer is operating normally.
Note that the pedometer cannot count steps correctly under the conditions described below. Avoid these
conditions whenever using the pedometer.
1. Irregular walking
Walking where it is crowded
Walking in sandals
Shuffling your feet
2. Any activity other than walking or jogging
Any activity that requires sudden standing or sitting
Jumping, or extreme activities or sports
Climbing or descending stairs or a steep slope
Vibration while riding on a car, train, bus, etc.
*Never start on any exercise program without consulting your physician, especially if you are currently under the
care of a physician, or if you have any past history of heart problems.
CHANGING MODES (PDM-20B)
Press the to cycle through the number of steps, distance, and calorie screens.MODE button
TO SET YOUR STRIDE LENGTH (PDM-20B)
1. Calculate your average stride length.
In a safe place, mark your starting point. Walk normally for 10 paces, and mark where you stop. Measure the
distance between the two marks, and then divide by 10.
6 m
10
9
8 6 4
2
7 5 3
1
60 cm
60 cm
2. While the number of steps screen is displayed, press the MODE button once to display the distance screen.
3. Press the SET button to display the stride length setting screen.
4. While the stride length setting screen is on the display, use the SET button to specify the average stride length
you calculated in step 1.
Each press of the SET button increases the displayed stride length by 1cm. You can set a value in the range
of 30cm to 180cm.
Holding down the changes the setting at high speed.SET button
The display will exit the stride length setting screen automatically if you do not perform any operation for a few
seconds.
5. After you are finished setting the stride length you want, simply wait and the pedometer will automatically exit
the stride length setting screen and return to the distance screen.
RESET
SET MODE
SET button
STRIDE
(cm)
STRIDE
(cm)
RESET
SET
MODE
DIS
(km)
DIS
(km)
STRIDE
(cm)
RESET
SET
MODE
DIS
(km)
TO SET YOUR CURRENT WEIGHT (PDM-20B)
1. While the number of steps screen is displayed, press the MODE button twice to display the calorie screen.
2. Press the SET button to display the weight setting screen.
3. While the weight screen is on the display, use the SET button to specify your current weight.
The display will exit the weight length setting screen automatically if you do not perform any operation for a
few seconds.
Each press of the increases the displayed weight by 1 kg. You can set a value in the range ofSET button
30 kg to 120 kg.
Holding down the changes the setting at high speed.SET button
4. After you are finished setting your weight, simply wait and the pedometer will automatically exit the weight
setting screen and return to the calorie screen.
CALORIE
(kcal)
CALORIE
(kcal)
WEIGHT
(kg)
WEIGHT
(kg)
WEIGHT
(kg)
RESET
SET MODE
SET button
RESET
SET
MODE
RESET
SET MODE
CALORIE
(kcal)
RESETTING THE PEDOMETER
(PDM-10B)
Press the to reset the number of steps to RESET button 0 .
(PDM-20B)
Press the to reset the number of steps, distance, and calories to RESET button 0 .
Note that the RESET operation does not affect the stride length and weight settings.
Before starting a new pedometer measurement operation, be sure to reset to 0 first.


Produkt Specifikationer

Mærke: Casio
Kategori: Ur
Model: PDM-10B

Har du brug for hjælp?

Hvis du har brug for hjælp til Casio PDM-10B stil et spørgsmål nedenfor, og andre brugere vil svare dig