Celestron Travel Scope 60 Manual

Celestron Teleskop Travel Scope 60

Læs gratis den danske manual til Celestron Travel Scope 60 (8 sider) i kategorien Teleskop. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Celestron Travel Scope 60, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Unpack your telescope and verify that all parts are present. Your

Travel Scope 60 includes: a telescope tube, a tripod and mount

head, two eyepieces, a 3x Barlow lens, a ﬁnderscope, an erect image

diagonal, and a Moon ﬁlter.

To extend the tripod’s central column, turn the locking knob

counterclockwise, lift up the tripod head until it is at the desired

height and turn the locking knob clockwise to secure.

Rotate the mounting platform so it is horizontal and tighten the knob

to secure it.

To set up the tripod, spread the legs outward until they are fully

extended and push down on the center leg brace.

Loosen the knob on the side of the tripod head mounting platform and

rotate the platform 90 degrees so it is standing vertically.

Remove the cap from the focuser end of the telescope tube and make

sure the two thumbscrews do not protrude into the opening.

Extend the legs of the tripod by unlocking the three tripod lock levers

on each leg. Pull each leg section all the way out and push the lever on

each lock downward to secure it in place.

Match the threaded bolt in the mounting platform to the threaded hole

on the bottom of the telescope tube and thread the two together. Do

not overtighten. This should be snug, but not tight.

Locate the erect image diagonal and remove the plastic covers. Insert

the barrel of the diagonal into the focuser and secure in place by

tightening the setscrews.

QUICK SETUP GUIDE

#22002-DS

Insert the barrel of the 20mm eyepiece into the diagonal and tighten

the setscrew.

Remove the knurled nuts on the threaded posts at the focuser end of

the telescope tube.

TRAVEL 60

SCOPE

Remove the lens cap from the front of the telescope. To observe, look

through the eyepiece as shown. Focus the image by turning the knobs

below the focuser.

To move the scope right and left, hold a tripod leg with one hand

while the other hand uses the panning handle to move the scope.

The azimuth locking screw can be loosened or tightened to adjust the

tension to your preference.

For additional magniﬁcation, you can use the included 3x Barlow lens.

Place the Barlow lens between the diagonal and the eyepiece.

To move the scope up and down, rotate the entire pan handle

counterclockwise and use the handle to point the scope in the

direction you want to view. Rotate the pan handle clockwise to

lock it in place.

Locate the ﬁnderscope and remove the plastic caps on the front and

back lenses. Orient the ﬁnderscope so that the larger lens is facing

towards the front of the tube as shown. Place the ﬁnderscope over the

posts on the tube and replace the knurled nuts to secure it in place.

To use the Moon ﬁlter, remove the eyepiece from the diagonal or

Barlow lens. Thread the ﬁlter onto the bottom of the eyepiece and

re-insert the eyepiece into the diagonal or Barlow.

CENTER THE TARGET IN THE EYEPIECE

Look through the telescope using your lower powered eyepiece.

Move the telescope until the object you chose lies in the center of

the view. If the image is blurry, gently turn the focus knobs until it

comes into sharp focus.

LOOK THROUGH FINDERSCOPE

Once the object is centered in your 20mm eyepiece, look through the

ﬁnderscope and locate the crosshair reticle.

ADJUST THE FINDERSCOPE

Without moving the telescope, use the three ﬁnger knobs on the

ﬁnderscope bracket to move the ﬁnder around in the bracket until

the crosshair appears over the same object you are observing in the

telescope’s 20mm eyepiece.

TIP: Try adjusting one screw at a time. Loosen one screw by half

a turn and tighten another by the same amount to ensure the

ﬁnderscope is securely held in place.

YOUR FINDERSCOPE

IS NOW ALIGNED!

It should not require realignment unless it is bumped or dropped .

The ﬁnder is one of the most important parts of your

telescope. It helps you locate objects and center them

in the eyepiece. The ﬁrst time you assemble your

telescope, you need to align the ﬁnder to the telescope’s

main optics. It’s best to do this during the day*.

* SOLAR WARNING! Never attempt to view the

Sun through any telescope without a proper solar

ﬁlter!

CHOOSE A TARGET

Take the telescope outside during the day and ﬁnd an easily

recognizable object, like a streetlight, license plate or sign. The object

should be as far away as possible, but at least a quarter mile away.

Low Power Eyepiece

Focus Knobs

ALIGNING THE

FINDERSCOPE

Produkt Specifikationer

Mærke:	Celestron
Kategori:	Teleskop
Model:	Travel Scope 60

Har du brug for hjælp?

Hvis du har brug for hjælp til Celestron Travel Scope 60 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Teleskop Celestron Manualer

Celestron Travel Scope 22035 Manual

16 November 2024

Celestron 90LCM Computerized Manual

25 August 2024

Celestron CPC 800 Deluxe HD Manual

24 August 2024

Celestron NexStar 8SE Manual

24 August 2024

Celestron CGEM - 925 Computerized Manual

16 August 2024

Celestron Omni XLT 102 Manual

5 August 2024

Celestron Mini Mak 70 Manual

5 August 2024

Celestron C6-NGT Computerized Manual

3 August 2024

Celestron StarSense Explorer Manual

2 August 2024

Celestron C6-RGT Computerized Manual

2 August 2024

Teleskop Manualer

Nyeste Teleskop Manualer

Levenhuk Skyline BASE 120S Manual

14 Juni 2025

Levenhuk Skyline BASE 60T Manual

14 Juni 2025

Levenhuk LabZZ TK76 Manual

14 Juni 2025

Levenhuk Skyline BASE 50T Manual

14 Juni 2025

Levenhuk Skyline PRO 80 MAK Manual

14 Juni 2025

Levenhuk LabZZ T2 Manual

14 Juni 2025

Levenhuk Skyline BASE 70T Manual

13 Juni 2025

Levenhuk Skyline PRO 90 MAK Manual

13 Juni 2025

Levenhuk Skyline BASE 80T Manual

13 Juni 2025

Levenhuk Skyline BASE 110S Manual

13 Juni 2025