Chauvet WELL Connect Manual

Chauvet Ikke kategoriseret WELL Connect

Læs gratis den danske manual til Chauvet WELL Connect (12 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Chauvet WELL Connect, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/12

English EN

Español ES

Français FR

Deutsch DE

Nederlands NL

Quick Reference Guide

Model ID: WELLCONNECT

Scan the QR code to

access the product page,

warranty terms, and the

complete User Manual

QUICK REFERENCE GUIDE

WELL CONNECT QRG Rev. 1

Safety Notes

These Safety Notes include important information about installation, use, and maintenance of the WELL CONNECT.

FCC Statement of Compliance

This device complies with Part 15 Part B of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment do interference to es cause harmful

radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

RF Exposure Warning for North America and Australia

Warning! This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with a minimum distance of 20 cm between the radiator and the user. This

transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

• CAUTION:

• This product’s housing may be hot when operating. Mount this product in a location with adeq

uate

ven

tilation, at least 20 in (50 cm) from adjacent surfaces.

• When transferring the product from extreme temperature environments, (e.g., cold truck to warm humi

llroom) condensation may form on the internal electronics of the product. To avoid causing a failure

allow the product to fully acclimate to the surrounding environment before connecting it to power.

• ALWAYS:

• Disconnect from power before cleaning the product or replacing the fuse.

• Replace the fuse with the same type and rating.

• Use a safety cable when mounting this product overhead.

• Connect this product to a grounded and protected circuit.

• DO NOT:

• Open this product. It contains no user-serviceable parts.

• Connect this product to a dimmer or rheostat.

• Operate this product if the housing or cables appear damaged.

• Operate this product outdoors or in any location where dust, excessive heat, water, or humidity may affe

(adhere to standards for the published IP rating).

• The maximum ambient temperature is 113 °F (45 °C). Do not operate this product at higher temperatures.

• The minimum startup temperature is -4°F (-20°C). Do not start the product at lower temperatures.

• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect th

oduct from power via breaker or by unplugging it.

• In the event of a serious operating problem, stop using immediately.

Connection of the control signal: DMX line

• The product has XLR sockets for DMX input and output.

• Notice: This control circuit is isolated and belongs to the Class 2 data port.

• The control circuit has a cumulative leakage current of less than 3.5 mA.

Produkt Specifikationer

Mærke:	Chauvet
Kategori:	Ikke kategoriseret
Model:	WELL Connect

Har du brug for hjælp?

Hvis du har brug for hjælp til Chauvet WELL Connect stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Chauvet Manualer

Chauvet Maverick Force X Profile Manual

20 August 2025

Chauvet Amhaze Stadium 2X IP Manual

20 August 2025

Chauvet Maverick Storm 3 Profile Manual

20 August 2025

Chauvet STRIKE Saber 10 Manual

20 August 2025

Chauvet Cloud 9X IP Manual

20 August 2025

Chauvet NovaStar MX20 Manual

17 August 2025

Chauvet SlimPAR T12BT ILS Manual

22 Juli 2025

Chauvet NovaStar MX203 Manual

20 Juni 2025

Chauvet WELL Connect Manual

20 Juni 2025

Chauvet VIP Drive 83R Nova Manual

19 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

NUX Amp Core Studio Manual

30 August 2025

Dometic TD283 Manual

30 August 2025

Laserworld PL-20 MK3 Manual

30 August 2025

Puls Dimension CP10.242 Manual

30 August 2025

Bebob S1MICRO Manual

30 August 2025

Be Quiet! Light Wings PWM 140x140x25 Manual

30 August 2025

Ventev CT-BKT-655 Manual

30 August 2025

American DJ ENCORE LP32IP Manual

30 August 2025

Thermex Caremex Hygiene Station Manual

30 August 2025

Bartscher TK60 Manual

30 August 2025