Cisco VWIC3-4MFT-T1/E1 Manual

Cisco Netværkskort/adapter VWIC3-4MFT-T1/E1

Læs gratis den danske manual til Cisco VWIC3-4MFT-T1/E1 (9 sider) i kategorien Netværkskort/adapter. Denne vejledning er vurderet som hjælpsom af 50 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 25.5 anmeldelser. Har du et spørgsmål om Cisco VWIC3-4MFT-T1/E1, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/9
Data Sheet
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information. Page 1 of 9
Cisco Third-Generation 1-, 2-, and 4-Port T1/E1 Multiflex Trunk
Voice/WAN Interface Cards
These flexible interface cards support multiple integrated data, voice and video applications, facilitating the
migration from data only as well as circuit-switched voice/video services to a packet voice/video solution
Introduction
The Cisco® Third-generation 1-, 2-port and 4-port T1/E1 Multiflex Trunk Voice/WAN Interface (MFT VWIC3s) support
data and voice applications on the Cisco 1921, 1941 and 1941W (data only), and the Cisco 2901, 2911, 2921, 2951,
3925, 3945, 3925E and 3945E Integrated Services Routers. The Cisco MFT VWIC3 combines WAN-interface-card
(WIC) and voice-interface-card (VIC) functions to provide unparalleled flexibility, versatility, and investment
protection through its many uses. Customers who choose to integrate data and voice in multiple steps preserve their
investment in a T1/E1 WAN interface because the Cisco MFT VWIC3 cards can be reused in packet voice
applications. The 2 port T1/E1 MFT VWIC3 is shown below.
Figure 1. Cisco 1-,2- and 4-Port T1/E1 MFT VWIC3
The Cisco MFT VWIC3 interface cards add improvements over the Cisco Second-generation 1- and 2-port T1/E1
Multiflex Voice/WAN Interface Cards (MFT VWIC2s). The Cisco 2- and 4-port MFT VWIC3s enable each port to be
clocked from an independent clock source for data applications. Voice applications can now be clocked
independently from data applications, with all ports for voice applications clocked from a single source. The Cisco
MFT VWIC3s use the ECAN on the motherboard PVDM cards with up to 128ms echo-tail length for demanding
network conditions. MFT VWIC3 cards support up to 2 channel groups per T1/E1 port for serial data applications.
Refer to Table 3 for all configuration options offered with the MFT VWIC3 cards.
The Cisco MFT VWIC3 cards can be inserted into the EHWIC slot on the supported Cisco 1921, 1941, 1941W,
2901, 2911, 2921, 2951, 3925, 3945, 3925E and 3945E integrated services routers. The T1/E1 MFT VWIC3 cards
support both T1 and E1, providing additional flexibility in configuring the Cisco MFT VWIC3s for supporting T1,
fractional T1, E1, and fractional E1 for both voice and WAN applications. All MFT VWIC3 modules include the drop-
and-insert multiplexing capability, which eliminates costly external third-party channel service units/data service units
(CSUs/DSUs) and drop-and-insert multiplexers.
Data Sheet
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information. Page 2 of 9
The Cisco MFT VWIC3 cards are offered in single-, dual- and quadruple-port versions, which can be used and then
redeployed as network requirements change, thereby addressing several applications:
● T1/E1 data: The Cisco 1-, 2- and 4-port T1/E1 MFT VWIC3 versions act as a WIC, supporting T1, fractional
T1, E1, (including structured G.703 with G.704 framing), fractional E1, and E1structured G.703 applications.
To simplify remote management, these MFT VWIC3 cards integrate a fully managed DSU/CSU for T1
deployments and a fully managed DSU for E1 deployments.
● E1/G.703 data: The Cisco 1- and 2- port G.703 MFT VWIC3 versions act as a WIC, supporting T1, fractional
T1, E1 (including structured G.703 with G.704 framing), fractional E1, and unstructured E1 (G.703)
applications. To simplify remote management, the G.703 version includes a fully managed DSU. The G.703
versions also support all the capabilities on the T1/E1 versions.
● T1/E1 packet voice: The Cisco 1-, 2- and 4-port T1/E1 MFT VWIC3 (voice and WAN) versions act as a VIC,
supporting packet voice applications by providing T1, fractional T1, E1, and fractional E1 connections to
private branch exchanges (PBXs) and central offices, thereby enabling new services and reducing voice and
fax toll charges.
● Mixed data and packet voice: The Cisco MFT VWIC3 interface cards can simultaneously support both data
and voice, reducing the complexity and number of network components and facilitating a graceful migration to
bandwidth-efficient packet voice.
● Mixed data and packet voice with drop and insert: The Cisco MFT VWIC3 cards can be deployed as a
T1/E1 drop-and-insert multiplexer with integrated DSUs/CSUs, reducing the complexity of the network and
the cost of the central-office ports by efficiently combining time-division multiplexing (TDM) voice (PBX), IP
voice, and data on the same trunks. Cisco 1900, 2900 and 3900 ISR routers support drop and insert between
ports over a single MFT VWIC3 card and two ports over two different MFT VWIC3s
Key Benefits
Reduces Networking Lifecycle Costs
● Enables graceful migration from data-only to multiplexed data and voice to packetized voice applications
● Reduces training, deployment, management, and sparing inventory over single-purpose interfaces
● Maximizes investment protection
● Simplifies network configuration and sparing through the support of both T1 and E1 on the same card
● Offers multifunction support for LAN-to-LAN routing, multiplexed data and voice, and packetized voice
● Offers ability to share modules among Cisco 1900, 2900 and 3900 Series routers
● Increases configuration flexibility and reduces cost for data applications by allowing individual ports to be
clocked from independent clock sources (not supported for voice applications, since all voice enabled ports
must be clocked from a single clock source)
● Supports E1 configurations for both balanced and unbalanced modes
● Supports (G.703 models) unstructured E1 (G.703) for using the full 2.048 Mbps
● Eliminates costly external third-party CSUs/DSUs and drop-and-insert multiplexers
● Simplifies remote network management by allowing a single management tool such as CiscoView or
CiscoWorks to support router, CSU/DSU, or drop-and-insert multiplexer
Maximizes System Resources
● Increases T1/E1 port density on the supported Cisco 2911, 2921, 2951, 3925, 3945, 3925E and 3945E
integrated services routers—up to four T1/E1 connections with an integrated CSU/DSU in a single EHWIC
slot

Produkt Specifikationer

Mærke: Cisco
Kategori: Netværkskort/adapter
Model: VWIC3-4MFT-T1/E1

Har du brug for hjælp?

Hvis du har brug for hjælp til Cisco VWIC3-4MFT-T1/E1 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Netværkskort/adapter Cisco Manualer

Cisco

Cisco CBS220-24P-4X Manual

7 Juli 2025
Cisco

Cisco C1000-16FP-2G-L Manual

7 Juli 2025
Cisco

Cisco CBS220-8P-E-2G Manual

6 Juli 2025
Cisco

Cisco CBS220-16T-2G Manual

6 Juli 2025
Cisco

Cisco CBS220-24FP-4X Manual

6 Juli 2025
Cisco

Cisco CBS220-24FP-4G Manual

6 Juli 2025
Cisco

Cisco CBS220-48P-4X Manual

6 Juli 2025
Cisco

Cisco CBS220-48FP-4X Manual

6 Juli 2025
Cisco

Cisco CBS220-8T-E-2G Manual

6 Juli 2025
Cisco

Cisco CBS220-8FP-E-2G Manual

6 Juli 2025

Netværkskort/adapter Manualer

Nyeste Netværkskort/adapter Manualer

ZyXEL

ZyXEL NWA50BE Manual

12 August 2025
ZyXEL

ZyXEL NWA50BE PRO Manual

12 August 2025
ZyXEL

ZyXEL NWA130BE Manual

12 August 2025
QNAP

QNAP QWA-AC2600 Manual

10 August 2025
Dell

Dell Brocade 6510 Manual

10 August 2025
IFM

IFM AL4323 Manual

9 August 2025
Planet

Planet VC-231GP Manual

8 August 2025
Planet

Planet FGSW-2624HPS4 Manual

8 August 2025
Planet

Planet LRP-822CS Manual

8 August 2025
Planet

Planet FTP-802S15 Manual

8 August 2025