Cleco 10L2582-01 Manual

Cleco Ikke kategoriseret 10L2582-01

Læs gratis den danske manual til Cleco 10L2582-01 (68 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Cleco 10L2582-01, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/68
GS-2007
02-2014
Cleco® - Dotco®
EN General Safety
DE Allgemeine Sicherheit
FR Sécurité générale
ES Seguridad General
IT Sicurezza generale
PT Segurança geral
NL Algemene veiligheid
DA Almindelig sikkerhed
SV Allmän säkerhet
NO Alminnelig sikkerhet
FI Yleinen turvallisuus
EL Γενικήασφάλεια
SL Splošna varnostna navodila
SK Všeobecnábezpečnosť
CS Všeobecnábezpečnost
ET Üldine ohutus
HU Általános biztonság
LT Bendroji sauga
LV Vispārējādrošība
PL Ogólnezasadybezpieczeństwa
BG Общабезопасност
RO Informaţiigeneraleprivindsecuritatea
RU Общиесведенияобезопасности
HR Općasigurnost
TR Genel Güvenlik
ZH 一般安全
JA 一般的な安全対策
KO 일반안전
TH
VI CácVấnĐềAnToànChung
ID Keselamatan Umum
MS Keselamatan Am
General Safety
Pneumatic Grinders
Page 2
GS-2007
02-2014
PRODUCT DESCRIPTION:
Pneumaticgrindersareportablehandheldtoolspowered
by compressed air. The motor drives a rotating spindle
on which a grinding wheel or other abrasive device is
mounted.Whenapplicable,thegrinderisequippedwith
a guard.
Failure to observe all safety warnings could result in
equipment damage or personnel injury.
INTENDED USE:
A pneumatic grinder is to be used only for removing
materialbyutilizingappropriateabrasivewheels,rotary
les or other material removal cutting devices. The
grinder must not be modied in any manner unless
approved in writing byApex Tool Group, LLC orApex
Tool Group GmbH & Co. OHG. All safety devices must
be properly installed and maintained in good working
order.
Any abuse or misuse of the cutting device can be
extremelydangerous.
GENERAL SAFETY INSTRUCTIONS:
These Safety Instructions must be accessible to the
operator at alltimes.They must beshownand made
available to all personnel involved in the operation of this
equipment.
The operator must read and understand the
Safety Instructions contained in this document
before operating this equipment.
These Safety Instructions are not intended to be all
inclusive. The operator should also read and understand
the Product Manual for the specic tool. Study and
comply with all applicable Federal, State and Local
Regulations.
Do not remove any labels from this equipment. Replace
any label that has been damaged and can not be easily
read.
PRODUCT INSTALLATION:
Only qualied and trained personnel should install,
adjust or use this equipment.
WORK ENVIRONMENT:
The work areamust beclean, uncluttered, thoroughly
ventilatedandwellilluminated.
Make sure the work environment is free of
any ammable or combustible elements that
sparks from the grinding process could ignite.
SPEED CHECK:
Checkthetoolspeedbeforemountingawheel,afterany
repairs,wheneverthetoolisissuedforuseorevery24
hours.TheRPMofthegrindermustbecheckedwitha
calibrated tachometer to make certain its actual speed
doesnotexceeditsratedspeed.
Carefullydetermineifthereisamaximumspeedmarked
on the cutting device. If so, this speed must be greater
thantheratedspeedofthetool.Failuretocomplywith
this instruction could result in serious injury or death.
GRINDING WHEEL INSPECTION:
Allgrindingwheelsshouldbecloselyinspectedbefore
installation and use. Consult the safety procedures of
thegrindingwheelmanufacturer.Includeblotterswhen
required.
PROPER ABRASIVE MOUNTING:
Therearemanytypesofcuttingwheelsincludingstraight,
cone, plug, cup, depressed center and mounted. Consult
and comply with the Safety Instructions of the cutting
wheel manufacturer. Insure the proper manufacturer
recommendedspindle,angesandguardsarepresent
on the tool.
Alwaysuseproperlymountedguards,asprescribedfor
the cutting device being used per ANSI/CAGI B186.1. If
the guard has been damaged, it must be discarded and
replaced.
Generally,rotarylesandsomeothercuttingdevicesdo
notrequirewheelguards.Conrmthiswiththecuttingtool
manufacturerandconformwiththeirrecommendations.
After mounting the cutting device and guard, the tool
should be started under a steel bench or similarly
protective area. Make sure safety glasses are worn.
Run at full speed for at least one minute to insure proper
operation.
GRINDING WITHOUT A GUARD:
Operators may use the grinder without a
guardonlyif they followtheserequirements.
Improper use of agrinder without a guard,
includingfailuretofollowtheserequirements,
could result in seriour injury or death.
Type 1 Wheel: Do not use a wheel larger than 2”
(50mm) in diameter or more than 1/2” (13mm) thick.
Neverexceedaperipheralspeedof1800surfacefeet
per minute (548.64m/min).
Type 1 Reinforced Wheel:Donotuseawheellarger
than3”(76mm)indiameterormorethan1/4”(6.4mm)
thick.Neverexceedaperipheralspeedof9500surface
feetperminute(2895.6m/min).
Grinding Wheels:Usedforinternalwork,whilewithin
theworkbeingground.
Mounted Wheels:Donotuseamountedwheelwitha
diametergreaterthan2”(50mm).
Other Cutting Devices: Do not use small cones, plugs,
threaded hole pot balls, or other similar devices that
exceed 3” (75mm) in diameter and 5” (125mm) long
withoutaguardunlesstheworkprovidesprotection.
CUT-OFF WHEELS (Type 1 and Type 27):
Securetheworkpiecetoprovideacleancutandreduce
the possibility of binding.
Ifthe cut-offwheel becomesjammed, turn thegrinder
offandfreethewheel.Makesurethewheelissecurely
attached and not damaged before continuing the
operation.
Never use a cut-off wheel to perform a side grinding
operation.
ENGeneral Safety
Pneumatic Grinders
WARNING
WARNING
WARNING

Produkt Specifikationer

Mærke: Cleco
Kategori: Ikke kategoriseret
Model: 10L2582-01

Har du brug for hjælp?

Hvis du har brug for hjælp til Cleco 10L2582-01 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Cleco Manualer

Cleco

Cleco CLBA403 Manual

4 Juli 2025
Cleco

Cleco CTBPW05Q Manual

30 Juni 2025
Cleco

Cleco S133410 Manual

23 September 2024
Cleco

Cleco NeoTek T55-3000020 Manual

23 September 2024
Cleco

Cleco NeoTek 937731PT Manual

23 September 2024
Cleco

Cleco 120XP ETWB340FR Manual

23 September 2024
Cleco

Cleco NeoTek 943462PT Manual

23 September 2024
Cleco

Cleco NeoTek 942396PT Manual

23 September 2024
Cleco

Cleco LiveWire 961350PT Manual

23 September 2024
Cleco

Cleco NeoTek 942391PT Manual

23 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Synology

Synology CMA-01 Manual

1 August 2025
Synology

Synology RKS-02 Manual

1 August 2025
Navman

Navman MiVue 765 SAFETY Manual

1 August 2025
Navman

Navman MY75T Manual

1 August 2025
Exquisit

Exquisit AIRFRY 3010 Manual

1 August 2025
Navman

Navman MiVue 155 SAFETY Manual

1 August 2025
Navman

Navman MiVue 698 Manual

1 August 2025
Newland

Newland FM550 Manual

1 August 2025
Tripp Lite

Tripp Lite SRIN4181810 Manual

1 August 2025
Navman

Navman MyTruck III Manual

1 August 2025