ComNet SFP-22A Manual

ComNet Ikke kategoriseret SFP-22A

Læs gratis den danske manual til ComNet SFP-22A (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 2 anmeldelser. Har du et spørgsmål om ComNet SFP-22A, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

INS_SFP-(X)_REV–

04/05/10

PAGE 1

INSTALLATION AND OPERATION MANUAL

SFP-(X)

COPPER AND OPTICAL FIBER ETHERNET CONNECTORS

The ComNet

™

selection of Small Form-Factor Pluggable modules allow for an

optical or copper interface when using a ComNet managed switch, unmanaged

switch or media converter.

These interchangeable SFP modules are available for use with copper media,

or multimode and single mode optical fiber. The optical fiber SFP modules are

available in fast Ethernet one and two fiber versions and Gigabit one and two

fiber versions. They also are available with LC or SC optical connectors.

The ComNet SFP modules have different wavelengths and optical power to

offer distances from 300 meters to 120 kilometers. These SFP modules are

industrially rated to perform in the most difficult operating environments.

The ComNet SFP interface is required for use with all ComNet SFP configurable

products to qualify for the ComNet Lifetime Warranty.

See Page 2 for complete installation instructions.

INS_SFP-(X)_REV–

04/05/10

PAGE 2

INSTALLATION AND OPERATION MANUAL SFP-(X)

SFP-(X) INSTALLATION/REMOVAL

CAUTION:

- The Fiber Optic sub-module is static sensitive. Use static handling precautions when installing or removing the sub-module.

- Protect your SFP sub-modules by inserting clean dust plugs into the SFP sub-modules after the optical fiber is extracted from

them. Be sure to clean the optic surfaces of the optical fiber before you plug them back into the optical bores of another SFP sub-

module. Avoid getting dust and other contaminants into the optical bores of your SFP sub-modules. The optics will not work cor-

rectly when obstructed by dust.

SFP Module:

- The SFP sub-module installs in the connector cage located on the unit corresponding to the port assignment to be used.

- The SFP sub-module is keyed and can only be installed in one orientation.

- The SFP sub-module (see Figure 1) has a bale clasp that you use to secure the SFP sub-module in a connector cage.

The photos used in the following sequence are intended to aid in the installation and removal of the SFP sub-module and may not

match your particular model.

Installation:

Step 1 - Flip the bale clasp up before inserting the SFP module.

Step 2 - Line up the SFP sub-module with the port and slide it

into the port. (see Figure 2)

Step 3 - When you are ready to attach the optical fiber, remove

the rubber plugs from the sub-module and save for

future use.

Note: When installed properly the SFP sub-module will lock in

place.

Removal:

Step 1 - Disconnect the optical fiber from the SFP sub-module.

Step 2 - Open the bale clasp on the SFP sub-module by press-

ing it down with your index finger as shown

in Figure 3.

Step 3 - Grasp the SFP sub-module between your thumb and

index finger and carefully remove it from the connector

cage as shown in Figure 4.

Step 4 - Install the rubber plugs back into the SFP sub-module

optical bores, and place the SFP sub-module in anti-

static protective packaging.



Figure 1

Figure 2

Figure 3

Figure 4

3 CORPORATE DRIVE | DANBURY, CT 06810 | USA

T: 203.796.5300 | F: 203.796.5303 | TECH SUPPORT: 1.888.678.9427 | INFO@COMNET.NET

8 TURNBERRY PARK ROAD | GILDERSOME | MORLEY | LEEDS, UK LS27 7LE

T: +44 (0)113 307 6400 | F: +44 (0)113 253 7462 | INFO-EUROPE@COMNET.NET

Produkt Specifikationer

Mærke:	ComNet
Kategori:	Ikke kategoriseret
Model:	SFP-22A
Produktfarve:	Nikkel
Opbevaringstemperatur (T-T):	-40 - 85 °C
Driftstemperatur (T-T):	-40 - 75 °C
Certificering:	MSA
Bæredygtighedscertifikater:	RoHS
Maksimal dataoverførselshastighed:	1000 Mbit/s
SFP modtagertype:	Fiberoptisk
Grænsefladetype:	SFP
Fiber optisk strømstik:	SC
Enkelttilstand fiber (SMF) understøttet:	Ja
Multitilstand fiber (MMF) understøttet:	Ingen
Maksimal overførselsafstand:	60000 m
Bølgelængde:	1310 nm
SFP transceiver standard:	FX