Crosley CRE3895PS Manual
Læs gratis den danske manual til Crosley CRE3895PS (32 sider) i kategorien Komfur. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Crosley CRE3895PS, eller vil du spørge andre brugere om produktet?
Side 1/32
T A B L E O F C O N T E N T S
Important Safety Instructions ...................... 3-5
Features ........................................................ 6
Before Setting Oven Controls .......................... 7
Before Setting Surface Controls .................... 8-9
Setting Surface Controls .......................... 10-13
Oven Control Functions ................................ 14
Setting Oven Controls ............................. 14-20
Self-Cleaning .......................................... 21-22
Care & Cleaning ...................................... 23-26
Before You Call ....................................... 27-28
Appliance Warranty .......................... Back Cover
Use & Care Manual
p/n 316902606 (1002)
READ AND SAVE THESE INSTRUCTIONS
Electric Range
330 control with
Ceramic Cooktop
2All rights reserved. Printed in the USA
PRODUCT RECORD AND REGISTRATION
Contents
Serial plate location:
open storage drawer (some models) or
remove lower front panel (some models).
Purchase date
Model number
Serial number
Record model & serial numbers here
Need help??
Read this Use & Care manual.
It contains instructions to help you use and maintain your
range properly.
If you received a damaged range ...
immediately contact the dealer (or builder) that sold you the
range.
Save time and money.
Check the section titled “Before you call”. This section helps
step you through some common problems that might occur.
If you do need service, help is only a phone call away. Call
customer service at 1-800-944-9044.
Product Registration
Congratulations on your purchase of a new range! At
Crosley Corporation, we are very proud of our product
and are completely committed to providing you with the best
service possible. Your satisfaction is our number one priority.
We know you’ll enjoy your new range and Thank You for
choosing our product. We hope you consider us for future
purchases.
Be sure to register your product. The self-addressed
PRODUCT REGISTRATION CARD should be filled in
completely, signed and returned to Crosley Corporation. To
find your product model and serial numbers see the
illustrations provided.
Serial plate location
Product Registration ...................................................... 2
Important Safety Instructions ............................ 3-5
Features ................................................................. 6
Before Setting Oven Controls .................................. 7
Removing, replacing & arranging the oven racks ........... 7
Before Setting Surface Controls ........................... 8-9
About the ceramic cooktop & radiant elements ............. 8
Cookware material types ............................................ 9
Setting Surface Controls .................................. 10-13
Setting single radiant surface elements ...................... 10
Setting dual radiant surface elements ........................ 11
Warming Zone ........................................................ 12
Home canning ......................................................... 13
Oven Control Functions ......................................... 14
Setting Oven Controls ...................................... 14-19
Setting the clock...................................................... 14
Changing oven temperature display (F° or C°) ............ 14
Setting silent control feature ..................................... 15
Setting minute timer ................................................ 15
Changing between continuous bake or 12-Hour
Energy Saving features ....................................... 15
Setting bake ........................................................... 16
Setting bake time .................................................... 16
Setting bake time and start time ............................... 17
Setting Convection ................................................... 18
Setting broil ............................................................ 19
Adjusting oven temperature ..................................... 20
Setting lockout feature ............................................. 20
Operating oven light ................................................. 20
Self-Cleaning .................................................... 21-22
Care & Cleaning ............................................... 23-26
Cleaning recommendation table ................................ 23
Cooktop maintenance & cleaning ........................... 24-25
Cautions for aluminum use ....................................... 25
Replacing the oven light ........................................... 25
Removing & replacing oven door ............................... 26
Before You Call
Solutions to common problems ............................. 27-28
Appliance Warranty ................................. Back Cover
This Use & Care Manual contains general operating
instructions for your range and feature information for
several models. Your appliance may not have all the
described features. The graphics shown are
representational and may not look exactly like those shown.
3
Read all instructions before using this appliance.
Do not attempt to install or operate your appliance until you
have read the safety precautions in this manual. Safety
items throughout this manual are labeled with a WARNING
or CAUTION statement based on the risk type.
WARNING indicates a potentially hazardous
situation which, if not avoided, may result in death
or serious injury.
Save these instructions for future reference.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
• Remove all tape and packaging before using the
range. Destroy the carton and plastic bags after
unpacking the range. Never allow children to play with
packaging material.
• Proper installation—Be sure your appliance is
properly installed and grounded by a qualified
technician in accordance with the National Electrical
Code ANSI/NFPA No. 70 latest edition and local
electrical code requirements. Install only per
installation instructions provided in the literature package
for this range.
WARNING
Stepping, leaning or sitting on the door or
drawers of a range can result in serious injuries
and also cause damage to the appliance. DO NOT
allow children to climb or play around the range. The
weight of a child on an open oven door may cause the
range to tip, resulting in serious burns or other injury.
Never use your appliance for warming or heating
the room.
Do not use the oven, warmer drawer or lower
oven (if equipped) for storage.
This is the safety alert symbol. It is used to alert you to
potential personal injury hazards. Obey all safety messages
that follow this symbol to avoid possible injury or death.
IMPORTANT
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in minor
or moderate injury.
CAUTION
IMPORTANT indicates installation, operation,
maintenance or valuable information that is not hazard
related.
Definitions
Important Safety Instructions
WARNING
• All ranges can tip.
• Injury to persons could result.
• Install anti-tip device packed
with range.
• See Installation Instructions.
To reduce the risk of tipping, the
range must be secured by properly
installed anti-tip bracket provided
with the range. To check if the
bracket is installed properly, visually
check that rear leveling leg is
inserted into and fully secured by the
anti-tip bracket by removing lower
front panel or storage drawer from
the range.
For models equipped with a warmer drawer or lower
oven, grasp the top rear edge of the range and carefully
attempt to tilt it forward. Refer to the installation
instructions for proper anti- tip bracket installation.
• User servicing—Do not repair or replace any part
of the appliance unless specifically recommended in
the manuals. All other servicing should be done only by a
qualified technician. This may reduce the risk of personal
injury and damage to the range.
Ask your dealer to recommend a qualified technician and
an authorized repair service. Know how to disconnect the
power to the range at the circuit breaker or fuse box in
case of an emergency.
• Remove the oven door from any unused range if it
is to be stored or discarded.
•Never modify or alter the construction of a range
by removing the leveling legs, panels, wire covers,
anti-tip brackets/screws, or any other part of the
range.
4
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
• Do not store items of interest to children in the
cabinets above a range or on the backguard of
the range. Children climbing on the range to reach
items could be seriously injured.
• Do not touch surface heating units or surface
cooking elements, areas near these units or
elements, or interior surface of the oven. Both
surface heating and oven heating elements may be hot
even though they are dark in color. Areas near surface
cooking units may become hot enough to cause burns.
During and after use, do not touch, or let clothing or
other flammable materials touch these areas until they
have had sufficient time to cool. Among these areas
are the cook top, surfaces facing the cook top, the
oven vent openings and surfaces near these openings,
oven door and oven door window.
• Wear proper apparel—loose-fitting or hanging
garments should never be worn while using the
appliance. Do not let clothing or other flammable
materials contact hot surfaces.
• Do not use water or flour on grease fires—
smother the fire with a pan lid, or use baking soda,
a dry chemical or foam-type extinguisher.
• When heating fat or grease, watch it closely. Fat
or grease may catch fire if allowed to become too hot.
• Use dry potholders - moist or damp potholders on
hot surfaces may result in burns from steam. Do
not let potholders touch hot heating elements. Do not use
a towel or other bulky cloth instead of a potholder.
• Do not heat unopened food containers - buildup of
pressure may cause container to burst and result
in injury.
IMPORTANT INSTRUCTIONS FOR USING
YOUR OVEN
• Use care when opening oven door , lower oven
door or warmer drawer (if equipped)—Stand to the
side of the range when opening the door of a hot oven.
Let hot air or steam escape before you remove or replace
food in the oven.
• Keep oven vent ducts unobstructed. The oven vent
is located under the left rear surface element if your
model is equipped with coil elements. The oven vent is
located below the backguard for models equipped with
ceramic-glass cook tops. Touching the surfaces in this
area when the oven is operating may cause severe
burns. Also, do not place plastic or heat-sensitive items
on or near the oven vent. These items could melt or
ignite.
• Placement of interior oven racks. Always place oven
racks in desired location while oven is cool. If rack must
be moved while oven is hot use extreme caution. Use
potholders and grasp the rack with both hands to
reposition. Do not let potholders contact the hot heating
elements in the oven. Remove all utensils from the rack
before moving.
• Do not use the broiler pan without its insert. The
broiler pan and its insert allow dripping fat to drain and
be kept away from the high heat of the broiler. Do not
cover the broiler insert with aluminum foil. Exposed
fat and grease could ignite.
• Protective liners—Do not use aluminum foil to line the
oven bottom. Only use aluminum foil as recommended in
this manual. Improper installation of these liners may
result in risk of electric shock, or fire.
Do not attempt to operate the range during a
power failure. If the power fails, always turn off the
range. If the range is not turned off and the power
resumes, the range will begin to operate again. Once the
power resumes, reset the clock and oven function.
IMPORTANT
• DO NOT LEAVE CHILDREN ALONE —children
should not be left alone or unattended in the
area where appliance is in use. They should never
be allowed to sit or stand on any part of the appliance,
including the storage drawer, lower broiler drawer,
warmer drawer or lower double oven.
• Storage in or on appliance—flammable materials
should not be stored in an oven, warmer
drawer, near surface units or in the storage
drawer. This includes paper, plastic and cloth items,
such as cookbooks, plasticware and towels, as well as
flammable liquids. Do not store explosives, such as
aerosol cans, on or near the range.
WARNING
6
Your electric range features include:
1. Electronic oven control with kitchen timer.
2. Interior oven light switch (some models).
3. Left front single (some models) or dual (some models) radiant
element control.
4. Left rear single radiant element control.
5. Warming Zone radiant element control (some models).
6. Right rear single radiant element control.
7. Right front single (some models) or dual (some models) radiant
element control.
8. Element ON indicator light(s).
9. HOT SURFACE indicator light(s).
10.Oven interior light with removable shield.
11.Automatic oven door light switch (some models).
12.Self-cleaning oven interior.
13.Self-clean door latch.
14.Adjustable interior oven rack(s).
15.Large 1-piece oven door handle.
16.Full width oven door with window.
17.Storage drawer (some models) or lower cover panel (some
models).
18.Easy to clean upswept cooktop.
19.Ceramic smoothtop (elements, styles and color will vary by model).
20.Warming Zone radiant element (some models).
21.6” single radiant element (some models).
22. 5-7” dual radiant element (some models).
23.9” single radiant element (some models).
24.6-9” dual radiant element (some models).
25.12” single radiant element (some models).
26.Leveling legs and anti-tip bracket (included).
FEATURES
1
2
3 4 5 6
9
7
8
10
11 13
15
14
16
17
18
21
26
12
19
20
22
21
22
23
25
24
The features shown for your appliance may vary according to model
type & color.
NOTE
23
24
25
7
Types of oven racks
Your range may be equipped with one or more of the oven
rack styles shown.
BEFORE SETTING OVEN CONTROLS
Oven vent location
The oven vent is located under the left side of the
control panel (See Fig. 1). When the oven is on, warm
air passes through this vent. This venting is necessary for
proper air circulation in the oven and good baking results.
Do not block the oven vent.
oven vent location
Fig. 1
flat
oven rack
flat handle
oven rack
offset
oven rack
The flat oven rack or flat handle oven rack (some
models) may be used for most cooking needs.
The offset oven rack (some models) is designed to place
the base of the rack about 1/2 of a rack position lower than
normal. This rack design provides several additional
possible locations between the standard positions.
Removing, replacing & arranging racks
Recommended rack positions by food type
Food type Position
Broiling meats See broil
Cookies, cakes, pies, biscuits & muffins 3 or 4
Frozen pies, angel food cake, yeast, bread
and casseroles 2 or 3
Small cuts of meat or poultry 2 or 3
Turkey, roast or ham 2
Air circulation in the oven
For best baking results allow 2-4" (5-10 cm) around the
cookware for proper air circulation and be sure pans and
cookware do not touch each other, the oven door, sides or
back of the oven cavity. Hot air must be able to circulate
around the pans and cookware in the oven for even heat to
reach around the food.
Baking layer cakes with 1 or 2 oven racks
For best results when baking cakes using 2 oven racks,
place cookware on rack positions 2 & 5 (See Fig. 3). For
best results when using a single oven flat rack, place
cookware on rack position 5 (See Fig. 4).
Fig. 3 Fig. 4
Always use oven mitts when using the oven. When
using the appliance, the oven interior, oven racks and
cooktop will become very hot which can cause burns.
CAUTION
Fig. 2
2
3
4
5
6
1
7
some
models
To remove - pull the rack
forward until it stops. Lift up
front of rack and slide out.
To replace - fit the rack onto
the guides on the oven walls.
Tilt the front of the rack
upward and slide the rack
back into place.
Arranging - always arrange
the oven racks when the oven
is cool (prior to operating the
oven).
8
NOTES
BEFORE SETTING SURFACE CONTROLS
About the ceramic glass cooktop
The ceramic cooktop has radiant surface elements located
below the surface of the glass. The design of the ceramic
cooktop outlines the area of the surface element
underneath. Be sure to match the pan size with the
diameter of the element outline on the cooktop and only
flat-bottomed cookware should be used.
The type and size of cookware, the number of surface
elements in use and their settings are all factors that will
affect the amount of heat that will spread to areas beyond
the surface elements. The areas surrounding the elements
may become hot enough to cause burns.
Be sure to read the detailed instructions for ceramic
glass cooktop cleaning in the Care & Cleaning and
Before You Call checklist sections of this Use & Care
Manual.
About the radiant surface elements
The element temperature rises gradually and evenly. As the
temperature rises, the element will glow red. To maintain
the selected setting the element will cycle ON and OFF. The
heating element retains enough heat to provide a uniform
and consistent heat during the off cycle.
For efficient cooking, turn OFF the element several minutes
before cooking is complete. This will allow residual heat to
complete the cooking process.
Radiant elements have a limiter that allows the element
to cycle ON and OFF, even at the HI setting. This helps
to prevent damage to the ceramic smoothtop. Cycling at
the HI setting is normal and will occur more often if the
cookware is too small for the radiant element or if the
cookware bottom is not flat.
Element On & Hot Surface indicator lights
Your appliance is equipped with two different types of
radiant surface control indicator lights located on the control
panel just above the surface control knobs on the control
panel — the On and
Hot Surface indicator lights.
The element On indicator light will glow when any surface
element is turned ON. A quick glance at this indicator light
after cooking is an easy check to be sure the surface
controls are turned OFF (See Fig. 1).
The Hot Surface indicator light will glow when any surface
cooking area heats up and will remain on
until the cooktop
has cooled to a MODERATE level (See Fig. 2).
element ON indicator light
Fig. 1
Fig. 2
hot surface indicator light
10
SETTING SURFACE CONTROLS
Single radiant surface elements (all models)
To operate the single radiant element:
1. Place correctly sized cookware on single radiant surface
element.
2. Push in and turn the surface control knob in either
direction (Fig. 2) to the desired setting (Refer to the
Suggested radiant surface element settings table
Fig. 1). Start most cooking operations on a higher setting
and then turn to a lower setting to finish cooking. The
surface control knobs do not have to be set exactly on a
particular spot. Use the graphics provided as a guide and
adjust the control knob as needed (See Fig. 2). Each
surface element provides a constant amount of heat at
each setting. A glowing red surface heating area
extending beyond the bottom edge of the cookware
indicates the cookware is too small for the surface
heating area.
3. When cooking is complete, turn the radiant surface
element OFF before removing the cookware.
The On indicator light will glow when one or more
elements are turned ON. A quick glance at this indicator
light when cooking is finished is an easy check to be sure
all control knobs are turned OFF. The Hot Surface
indicator light will continue to glow AFTER the control
knob is turned to the “OFF” position and will glow until
the heating surface area has cooled sufficiently.
The suggested settings found in Fig.1 below are based
when cooking with medium-weight aluminum pans with
lids. Settings may vary when using other types of pans.
Suggested radiant surface element
settings
The size and type of utensil used, and the amount and
type of food being cooked will influence the setting
needed for best cooking results.
NOTES
Fig. 2
Radiant surface elements may appear to have cooled
after they have been turned off. The glass surface may
still be hot and burns may occur if the glass surface is
touched before it has cooled sufficiently.
Do not place flammable items such as plastic salt and
pepper shakers, spoon holders or plastic wrappings on
top of the range when it is in use. These items could melt
or ignite. Potholders, towels or wooden spoons could
catch fire if placed too close to the surface elements.
CAUTION
IMPORTANT
Do not allow aluminum foil, or ANY material that can
melt to make contact with the ceramic glass cooktop.
If these items melt on the cooktop they will damage the
ceramic cooktop.
Suggested settings for single and dual radiant
elements table
Settings Type of cooking
High (hi - 9) Start most foods, bring water to a
boil, pan broiling
Medium high (7 - 8) Continue a rapid boil, fry, deep fat fry
Medium (med, 5 - 6) Maintain a slow boil, thicken sauces
and gravies or
steam vegetables
Medium Low (2 - 4) Keep foods cooking, poach, stew
Low (lo - 1) Keep warm, melt, simmer
Fig. 1
11
Radiant surface elements may appear to have cooled
after they have been turned off. The glass surface may
still be hot and burns may occur if the glass surface is
touched before it has cooled sufficiently.
Do not place flammable items such as plastic salt and
pepper shakers, spoon holders or plastic wrappings on
top of the range when it is in use. These items could melt
or ignite. Potholders, towels or wooden spoons could
catch fire if placed too close to the surface elements.
CAUTION
Heating with inner (small)
element only
Heating with both
elements
Fig. 1 Fig. 2
Dual radiant surface elements (some models)
Symbols on the backguard are used to indicate which coil of
the dual radiant element will heat. The symbol indicates
settings for the inner element only. The symbol
indicates settings for both inner and outer elements.
You may switch from either coil setting at any time during
cooking. See
Suggested radiant surface element
settings table on previous page.
To operate a dual radiant element:
1. Place correctly sized cookware on dual radiant surface
element.
2. Push in and turn the surface control knob clockwise to
begin heating both the inner and outer portions of the
dual element. If only the inner heating portion is needed
for smaller cookware, push in and turn the knob counter-
clockwise to start.
3. When cooking is complete, turn the dual radiant surface
element OFF before removing the cookware.
Areas that heat are shown darkened.
Start most cooking operations on a higher setting and then
turn to a lower setting to finish cooking. The surface control
knobs do not have to be set exactly on a particular mark.
Use the marks as a guide and adjust the control knob as
needed. A glowing red surface heating area extending
beyond the bottom edge of the cookware indicates the
cookware is too small for the surface heating area.
The size and type of utensil used, and the amount and
type of food being cooked will influence the setting
needed for best cooking results.
NOTES
IMPORTANT
Do not allow aluminum foil, or ANY material that can
melt to make contact with the ceramic glass cooktop.
If these items melt on the cooktop they will damage the
ceramic cooktop.
SETTING SURFACE CONTROLS
The On indicator light will glow when one or more
elements are turned ON. A quick glance at this indicator
light when cooking is finished is an easy check to be sure
all control knobs are turned OFF. The Hot Surface
indicator light will continue to glow AFTER the control
knob is turned to the “OFF” position and will glow until
the heating surface area has cooled sufficiently.
12
SETTING SURFACE CONTROLS
Warming Zone (some models)
The purpose of the warming zone is to keep hot cooked
foods at serving temperature. Use the keep warm feature
to keep cooked foods hot such as; vegetables, gravies,
casseroles, soups, stews, breads, pastries and oven-safe
dinner plates.
Always start with hot food. It is not recommended to heat
cold food on the Warming Zone. All food placed on the
warming zone should be covered with a lid to maintain
quality.
For best results, when warming pastries or breads, the
cover should have an opening to allow moisture to escape.
Do not use plastic wrap to cover food. Plastic may
melt onto the surface and be very difficult to clean.
Use only dishware, utensils and cookware recommended
for oven and cooktop use on the Warming Zone zone.
Setting the Warming Zone control
1. Push in either direction and turn the knob (See Fig 1).
The temperatures are approximate, and are designated
by hi, med and lo
. However, the control can be set at
any position between hi and lo for different levels of
warming.
2. When ready to serve, turn the control to OFF. The
Warming Zone will remain warm until the indicator
light goes OFF.
Unlike the surface elements, the Warming Zone will not
glow red when it is hot.
Always use potholders or oven mitts when removing food
from the Warming Zone as cookware and plates
will be
hot.
Radiant surface elements may appear to have cooled
after they have been turned off. The glass surface may
still be hot and burns may occur if the glass surface is
touched before it has cooled sufficiently.
Do not place flammable items such as plastic salt and
pepper shakers, spoon holders or plastic wrappings on
top of the range when it is in use. These items could melt
or ignite. Potholders, towels or wooden spoons could
catch fire if placed too close to the surface elements.
CAUTION
Temperature selection - Refer to the Warming Zone
recommended food settings table (See Fig. 2). If a
particular food is not listed, start with the medium level,
and adjust as needed. Most foods can be kept at serving
temperatures by using the medium level.
Warming Zone recommended food settings table
Food Item Heating Level
Breads/Pastries LO (Low)
Casseroles LO (Low)
Dinner Plates with Food LO (Low)
Eggs LO (Low)
Gravies LO (Low)
Meats MED (Medium)
Sauces MED (Medium)
Soups (cream) MED (Medium)
Stews MED (Medium)
Vegetables MED (Medium)
Fried Foods HI (High)
Hot Beverages HI (High)
Soups (liquid) HI (High) Fig. 2
IMPORTANT
Do not allow aluminum foil, or ANY material that can
melt to make contact with the ceramic glass cooktop.
If these items melt on the cooktop they will damage the
ceramic cooktop.
Fig. 1
13
Home Canning
Be sure to read and observe all the following points when
home canning with your appliance. Check with the USDA
(United States Department of Agriculture) website and be
sure to read all the information they have available as well
as follow their recommendations for home canning
procedures.
Radiant surface elements may appear to have cooled
after they have been turned off. The glass surface may
still be hot and burns may occur if the glass surface is
touched before it has cooled sufficiently.
Do not place flammable items such as plastic salt and
pepper shakers, spoon holders or plastic wrappings on
top of the range when it is in use. These items could melt
or ignite. Potholders, towels or wooden spoons could
catch fire if placed too close to the surface elements.
CAUTION
• Use only quality flat bottom canners when home canning.
Use a straight-edge to check canner bottom (see
“Cookware material types” in the Before setting
surface controls section).
• Use only a completely flat bottom canner with no
ridges that radiate from the bottom center when home
canning using a ceramic cooktop.
• Make sure the diameter of the canner does not
exceed 1 inch beyond the surface element
markings or burner. It is recommended to use smaller
diameter canners on electric coil and ceramic glass
cooktops.
• Start with hot tap water to bring water to boil more
quickly.
• Use the highest heat seating when first bringing the water
to a boil. Once boiling is achieved, reduce heat to lowest
possible setting to maintain that boil.
IMPORTANT
Do not allow aluminum foil, or ANY material that can
melt to make contact with the ceramic glass cooktop.
If these items melt on the cooktop they will damage the
ceramic cooktop.
SETTING SURFACE CONTROLS
IMPORTANT
NEVER place or straddle a cooking utensil over 2 different
surface cooking elements at the same time. This can
cause uneven heating results. For models equipped with
a ceramic cooktop, uneven heating between different
cooking elements may cause the glass cooktop to
fracture.
14
OVEN CONTROL FUNCTIONS
Changing temperature display (°F or °C)
The electronic oven control is set to display °F (Fahrenheit)
when shipped from the factory. The oven may be
programmed for any temperature from 170°F to 550°F
(77°C to 287°C).
READ THE INSTRUCTIONS CAREFULLY BEFORE USING THE OVEN.
For satisfactory use of your oven, become familiar with the various pad features and functions of the oven as described below.
Up and down arrow pads— Use with the
feature or function pads to set oven
temperature, bake time, start time, clean time
(when programming an automatic start time),
setting or adjusting the clock and minute timer.
Start time pad—
Use to set the
desired start time
for baking & Self-
Clean. May be used
with Bake time to
program a delayed
timed bake.
Bake time pad— Use
to enter the length of
baking time desired.
Feature indicator
lights — These
indicator lights show
which feature is active.
Setting the Clock
When the appliance is first plugged in or when the power
supply to the appliance has been interrupted, the display
will flash “12:00”.
To set the clock:
1. Press Clock once (do not hold key pad down).
2. Within 5 seconds, press and hold the or until
the correct time of day appears in the display.
NOTES
To change the temperature to display °C (Celsius) or
from °C to °F:
1. Press Broil. “— —” appears in the display.
2. Press and hold the until "HI" appears in the display.
3. Press and hold Broil until °F or °C appears in the display.
4. Press the or to change °F to °C or °C to °F.
5. Press any control pad to return to normal operating
mode.
NOTE
Broil pad— Use to select
the variable broil feature.
The time of day must first be set in order to operate the
oven.
The clock cannot be changed when the oven is set for
cooking or Clean is active.
The temperature display feature cannot be changed
when the oven is set for cooking or Clean is active.
Bake pad—Use to
select the bake feature.
Timer On/Off pad— Use
to set or cancel the minute
timer. The minute timer does
not start or stop cooking.
Timer On/Off pad is used
to set the continuous bake
function.
Oven, Preheat and Door Locked lights — The
"Oven" light will glow each time the oven turns on to
maintain the set oven temperature. The "Preheat" light
will glow when the oven is first set to operate, or if the
desired temperature is reset higher than the actual oven
temperature. The "Door Locked" light will flash when
the oven door locks and unlocks, the oven door lockout is
active or when the self-clean cycle feature is active.
Clean pad— Use to set
a Self-clean cycle. Clear/Off pad— Use to
clear any feature
previously entered except
the time of day and
minute timer. Press
Clear/Off to stop
cooking.
Also use Clear/Off to
activate oven lockout
feature.
Clock pad— Use to set
the time of day.
SETTING OVEN CONTROLS
Oven Light— Use to
turn interior oven light
on and off
Convec pad— Use to
select the convection
feature.
15
Changing between continuous bake
setting or 12-Hour Energy Saving feature
The oven control has a built-in 12-Hour Energy Saving
feature that will shut off the oven if the oven is left on for
more than 12 hours. The oven control can be programmed
to override this feature for continuous baking.
Changing to continuous bake setting:
1. Press and hold Timer On/Off down for 6 seconds until a
tone sounds. “— — hr” will appear in display for
continuous cooking. The current time of day will return
to the display.
2. To cancel the continuous bake setting, press Timer On/
Off and hold for 6 seconds until a tone sounds. “12hr”
will appear in display indicating that the control has
returned to the 12-Hour Energy Saving feature.
Setting a silent control panel
When choosing a function, a tone will sound each time a
keypad is pressed. If desired, the control can be
programmed for silent operation.
To block the controls from sounding when any keypad is
pressed in the future, press and hold Start time keypad
for 6 seconds. The control will beep once then release the
keypad.
To return the tones, press and hold Start time again for 6
seconds until the control beeps once.
Setting the minute timer
1. Press
Timer On/Off
.
2. Press the to increase the time in one minute
increments. Press and hold the to increase the time
in 10 minute increments. The timer can be set for any
amount of time from 1 minute to 11 hours and 59
minutes.
Note: If the
pad is pressed first, the timer will
advance to 11 hours and 59 minutes.
3. When the set time has run out, the timer will beep 3
times and will continue to beep 3 times every 60 seconds
until Timer On/Off is pressed.
To change the timer while it is in use
While the timer is active and shows in the display, press
and hold the or to increase or decrease the time
remaining.
To cancel the minute timer before the set time has
run out
Press Timer On/Off once .
NOTES
•The indicator light located above the Timer On/Off
pad will glow while the minute timer is active.
•The minute timer will display hours and minutes until 1
hour remains on the timer. Once less than 1 hour
remains, the display will count down in minutes and
seconds. Once the timer has less than 1 minute
remaining only seconds will display.
•The minute timer will not start or stop the cooking
process. It serves as an extra timer in the kitchen that
will beep when the set time has run out. The minute
timer can be used alone or while using any of the other
oven features. If another feature is active when the
minute timer is active, the minute timer will show in the
display. To view information about other active
features, press the pad for that feature.
IMPORTANT
This feature does not change how the cooktop controls
operate.
SETTING OVEN CONTROLS
16
SETTING OVEN CONTROLS
Setting Bake
The oven can be programmed to bake at any temperature
from 170°F to 550°F (77°C to 287°C). The factory preset
automatic bake temperature is 350°F (177°C).
To set Bake
1. Press Bake. “— — —” appears in the display.
2. Within 5 seconds, press the or . The display
will show 350°F (177°C). By pressing and holding
the or , the temperature can then be adjusted in
5°F increments (1°C if the control is set to display Celsius).
3. As soon as the or pad is released, the oven
will begin heating to the selected temperature. When the
displayed temperature reaches the desired baking
temperature, the preheat indicator light will turn OFF and
the control will beep 3 times.
Use caution with the timed bake and delayed timed bake
features. Foods that can easily spoil such as milk, eggs,
fish, meat or poultry, should be chilled in the refrigerator
first. Even when chilled, they should not stand in the
oven for more than 1 hour before cooking begins, and
should be removed promptly when finished cooking.
To program the oven to begin baking immediately
and to shut off automatically (timed bake)
1. Be sure that the clock shows the correct time of day.
2. Place the food in the oven.
3. Press Bake
. “— — — °” appears in the display.
4. Within 5 seconds, press the or . The display will
show "350°F (177°C)." By holding the or , the
temperature can then be adjusted in 5°F increments
(1°C if the control is set to display Celsius).
5. Press Bake time. ":00" will appear in the display.
6. Press the or until the desired baking time
appears in the display.
7. The oven will turn ON and begin heating.
FOOD POISONING HAZARD. Do not let food sit for more
than one hour before or after cooking. Doing so can result
in food poisoning or sickness.
CAUTION
WARNING
To change the oven temperature after bake has
started
1. Press Bake. Visually check the bake temperature and
that it needs to be changed.
2. Press the or pad to increase or decrease the set
temperature to the desired new oven temperature.
NOTES
•The Oven indicator light on the electronic display will
turn ON and OFF when using the Bake feature and
during preheat. This is normal and indicates that the
oven is cycling to maintain the selected baking
temperature.
•When the Preheat indicator light turns OFF, your oven
is ready.
•To cancel baking at any time, press Clear/Off.
Dark or dull pans absorb more heat than shiny bakeware
resulting in dark or overbrowning of foods. It may be
necessary to reduce the oven temperature or cook time
to prevent overbrowning of some foods. Dark pans are
recommended for pies. Shiny pans are recommended
for cakes, cookies and muffins.
IMPORTANT
Setting Bake time
The Bake time pad sets the amount of time needed for
baking. The oven will turn on immediately and stop
automatically after the set bake time ends.
NOTES
•Bake time will not operate when using the broil feature.
•To cancel baking at any time, press Clear/Off.
17
To program oven for a delayed start time and to
shut-off automatically
1. Be sure that the clock displays the correct time of day.
2. Place food in the oven.
3. Press Bake. “— — — °” appears in the display.
4. Within 5 seconds, press the or . The display will
show 350°F (177°C). By holding the or , the
temperature can then be adjusted in 5°F increments
(1°C if the control is set to display Celsius).
5. Press Bake time. “:00” will appear in the display.
6. Press the or until the desired baking time
appears.
7. Press Start time. The time of day will appear in the
display.
8. Press the or until the desired start time appears
in the display.
9. Once the controls are set, the control calculates the time
when baking will stop.
10.The oven will turn ON at the delayed start time and
begin heating. The oven will turn OFF after the set bake
time ends.
When the set bake time runs out
1. “End” will appear in the display window and the oven
will shut-off automatically.
2. The control will beep 3 times every 60 seconds as a
reminder until is pressed.Clear/Off
To change the oven temperature or bake time after
baking has started
1. Press the function pad you want to change.
2. Press the or to adjust the setting.
NOTE
During a delayed timed bake the preheat indicator light
will not function until the set time to start cooking is
reached.
Use caution with the timed bake and delayed timed bake
features. Foods that can easily spoil such as milk, eggs,
fish, meat or poultry, should be chilled in the refrigerator
first. Even when chilled, they should not stand in the
oven for more than 1 hour before cooking begins, and
should be removed promptly when cooking is completed.
FOOD POISONING HAZARD. Do not let food sit for more
than one hour before or after cooking. Doing so can result
in food poisoning or sickness.
Setting Bake time and Start time
The Bake time and
Start time pads may be used to set the
length of baking time and to delay the starting time (delayed
timed bake). The oven will turn on at a later time and stop
automatically after the set bake time ends.
Dark or dull pans absorb more heat than shiny bakeware
resulting in dark or overbrowning of foods. It may be
necessary to reduce the oven temperature or cook time
to prevent overbrowning of some foods. Dark pans are
recommended for pies. Shiny pans are recommended
for cakes, cookies and muffins.
IMPORTANT
WARNING
CAUTION
SETTING OVEN CONTROLS
18
6
1
2
3
4
5
7
SETTING OVEN CONTROLS
Benefits of Convec feature
— Foods may cook up to 25 to 30% faster, saving time and
energy.
— Multiple rack baking.
— No special pans or bakeware needed.
1. Press Convec. key pad.
2. To accept press the or once. To change the
oven temperature use the or key pad to adjust
and release key pad to accept.
To cancel Convec feature at anytime press Clear/Off
key pad.
To set Convec feature with the default oven set
temperature of 350°F:
Setting Convec (Convection)
Air movement using Convec. feature
Fig. 1
some
models
•The convection fan will begin rotating once Convec
feature has been activated.
•If the oven door is opened when Convec feature is
active, the convection fan will stop rotating until the
oven door is closed.
•When using Convec feature cook time reductions may
vary depending on the amount and type of food being
cooked.
•Layer cakes will have better results using the normal
Bake feature.
•Dark or dull pans absorb more heat than shiny
bakeware resulting in dark or overbrowning of foods.
It may be necessary to reduce the oven temperature
or cook time to prevent overbrowning of some foods.
Dark pans are recommended for pies. Shiny pans are
recommended for cakes, cookies and muffins.
Suggestions for Convec:
•For optimum cooking results it is recommended to
preheat the oven when baking foods such as cookies,
biscuits and breads.
•Reduce oven temperature 25°F from recipe’s
recommended oven temperature. Follow the remainder
of the recipe’s instructions using the minimum
recommended cook time.
•For best results when using a single oven rack, place
rack in position 4 or 5 (See Fig. 1). When using 2 oven
racks, place in positions 2 & 5. When using 3 oven racks
place in positions 2, 4, & 7 (use offset rack only in
position 7).
The Convec feature uses a fan to circulate the oven's heat
uniformly and continuously around the oven. This improved
heat distribution allows for fast, even cooking and browning
results. It also gives better baking results when using two
oven racks at the same time.
Heated air flows around the food from all sides, sealing in
juices and flavors. Breads and pastry brown more evenly.
Most foods baked in a standard will cook faster and more
evenly with the convection feature. Convec may be set for
any oven temperature between 170°F (77°C) to 550°F
(288°C).
NOTES
19
SETTING OVEN CONTROLS
To set Broil
1. Arrange the oven rack while oven is still cool.
2. Press Broil. “— —” will appear in display.
3. Press and hold the or until the desired broil
setting level appears in the display. Press the for HI
broil or the for LO broil. Most foods may be broiled
at the HI broil setting. Select the LO
broil setting to avoid
excess browning or drying of foods that should be
cooked to the well-done stage.
4. For optimum results, preheat oven for 5 minutes
before adding food.
5. Place the insert on the broil pan (if equipped), then place
the food on the broil pan insert (if equipped).
6. Place the broiler pan and insert (if equipped) on the
oven rack (See Figs. 1 & 2).
7. Open the oven door to the broil stop position when
broiling.
8. Broil on one side until food is browned. Turn and broil
food on 2nd side.
9. When broiling is finished press Clear/Off.
Use the broil feature to cook meats that require direct
exposure to radiant heat for optimum browning results.
When broiling always remember to arrange the oven racks
while oven is still cool. Position the rack as suggested in the
broil settings table (See Figs. 1 & 3).
Setting Broil
Suggested broil settings table (electric oven)
Food Rack position Setting Cook time in minutes
1st side 2nd side Doneness
Steak 1” thick 6th or 7th* Hi 6 4 Medium
Steak 1” thick 6th or 7th* Hi 7 5 Medium-well
Steak 1” thick 6th or 7th* Hi 8 7 Well
Pork chops 3/4” thick 6th Hi 8 6 Well
Chicken-bone in 5th Lo 20 10 Well
Chicken-boneless 6th Lo 8 6 Well
Fish 6th Hi 13 n/a Well
Shrimp 5th Hi 5 n/a Well
Hamburger 1” thick 7th* Hi 9 7 Medium
Hamburger 1” thick 6th Hi 10 8 Well
Insert
Broil pan
Fig. 1
Fig. 3
Fig. 2
NOTE
Always pull the oven rack out to the stop position before
turning or removing the food.
*Use the off-set rack (some models) if you choose to use oven rack position 7.
CAUTION
WARNING
Should an oven fire occur, close the oven door and turn
the oven OFF. If the fire continues, use a fire
extinguisher. DO NOT put water or flour on the fire. Flour
may be explosive.
The broil pan and the insert (if equipped) allows grease
to drain and be kept away from the high heat of the
broiler. DO NOT use the pan without the insert. DO NOT
cover the insert with aluminum foil; the exposed grease
could ignite.
2
3
4
5
6
1
7
some
models
20
Your appliance has been factory calibrated and tested to
ensure an accurate baking temperature. For the first few
uses, follow your recipe times and temperature
recommendations carefully. If you think the oven is cooking
too hot or too cool for your recipe times, you can adjust the
control so the oven cooks hotter or cooler than the
temperature displayed.
To adjust oven temperature:
1. Press Bake.
2. Set the temperature to 550°F (287°C) by pressing and
holding the .
3. Within 2 seconds, press and hold Bake until numeric
digit(s) appear. Release Bake keypad.
The display now
indicates the amount of degrees offset between the
original factory temperature setting and the current
temperature setting. If the oven control has the original
factory calibration, the display will read "0."
4. The temperature can now be adjusted up or down 35°F
(19°C), in 5°F increments by pressing and holding the
or . Adjust until the desired amount of offset
appears in the display. When lowering the oven
temperature, a minus sign (-) will appear before the
number to indicate that the oven will be cooler by the
displayed amount of degrees.
5. When you have made the desired adjustment, press
Clear/Off to go back to the time of day display.
Adjusting the oven temperature
Oven temperature adjustments made will not affect the
broil or self-cleaning feature temperatures.
If the display is set for Celsius, adjustments made will be in
1°C increments each press of the or
keys.
DO NOT USE oven thermometers such as those found in
grocery stores to check the temperature settings inside your
oven. These oven thermometers may vary as much as 20 to
40 degrees from actual temperatures.
NOTES
DO NOT open the oven door while the indicator light
is flashing. Allow about 15 seconds for the oven door to
lock. Once the oven door is locked, the current time of
day will appear in the display.
If any control pad is pressed with the oven lockout
feature active, “Loc” will appear in the display until the
control pad is released.
NOTES
Operating oven light (some models)
The interior oven light will automatically turn ON when the
oven door is opened. Press the Oven Light keypad to turn
the oven light on or off whenever the oven door is closed.
To change the interior oven light, see “Changing the oven
light” in the Care & Cleaning section.
SETTING OVEN CONTROLS
To set the lockout feature
1. Press Clear/Off and hold for 3 seconds. “Loc” will
appear in display, the “Door Locked” indicator light will
flash and the motor driven door lock will begin to close
automatically. Allow about 15 seconds for the oven
door to lock. Once the oven door is locked, the current
time of day will appear in the display.
2. To cancel the lockout feature, press Clear/Off and hold
for 3 seconds. The control will unlock the oven door and
resume normal operation.
Setting lockout feature
The control may be programmed to lock
the oven door and lockout the oven
control pads.
21
SELF-CLEANING
Self-Cleaning
A self-cleaning oven cleans itself with high temperatures
(well above normal cooking temperatures) which eliminate
soils completely or reduces them to a fine powdered ash
you can wipe away with a damp cloth.
CAUTION
For models that have a visible lower bake element
ONLY - This bake element was designed to be tilted up
using your hand from the front of the bake element for
cleaning purposes. Remove the bottom oven rack before
raising the element. Do not to raise the element more
than 4 or 5 inches from the resting position.
The oven bake and broil elements may appear to have
cooled after they have been turned OFF. The elements
may still be hot and burns may occur if these elements
are touched before they have cooled sufficiently.
Adhere to the following self-clean precautions:
• DO NOT use oven cleaners or oven protective coatings
in or around any part of the oven interior.
• DO NOT clean the oven door gasket (See Fig. 1). The
woven material of the oven door gasket is essential
for a good seal. Care should be taken not to rub,
damage or remove the gasket.
• DO NOT use any cleaning materials on the oven door
gasket. Doing so could cause damage.
• Remove the broiler pan and insert, all utensils
and ANY ALUMINUM FOIL. These items cannot
withstand high cleaning temperatures and will
melt.
• Completely remove ALL OVEN RACKS and ANY
ACCESSORIES. If the oven racks are not
removed they can discolor or lose their special
coating properties and no longer slide in and
out of the oven cavity easily.
• Remove any excessive spillovers. Any spills on
the oven bottom should be wiped-up and removed
before starting the self-cleaning cycle. To clean, use
hot, soapy water and a cloth. Large spillovers can
cause heavy smoke or fire when subjected to high
temperatures. DO NOT allow food spills with a high
sugar or acid content (such as milk, tomatoes,
sauerkraut, fruit juices or pie filling) to remain on the
surface as they may leave a dull spot even after
cleaning.
•Clean any soil from the oven frame, the door liner
outside the oven door gasket and the small area at the
front center of the oven bottom. These areas heat
sufficiently to burn soil on. Clean with soap and water.
These areas are shown in white (See Fig. 1).
CAUTION
IMPORTANT
During the self-cleaning cycle, the outside of the range
can become very hot to the touch. DO NOT leave small
children unattended near the appliance.
The health of some birds is extremely sensitive to the
fumes given off during the self-cleaning cycle of any
range. Move birds to another well-ventilated room.
DO NOT force the oven door open. This can damage the
automatic door locking system. Use caution when
opening the door after the self-cleaning cycle is
complete. The oven may still be VERY HOT.
Fig. 1
IMPORTANT
22
1. Be sure the oven is empty, all oven racks are removed,
all items are cleared from cooktop and the over door is
completely closed. Be sure the clock displays the correct
time of day.
2. Press Start time. The “:” in the time of day will flash.
3. Press and hold the pad to scroll to the time to start a
delayed self-clean cycle. Release the key pad when the
desired time displays.
4. Press Clean. “---” appears in the display.
5. Press the or pad once. “3:00” will appear in the
display indicating that a 3 hour self-clean time is set. To
change to a 2 hour self-clean time press once (2:00
appears in the display).
(Some models) For a 4 hour self-clean time press
until (4:00 appears in display).
6. “CLn” will appear in the display during the self-clean
cycle and the “Door Locked” indicator light will glow until
the self-cleaning cycle is complete or cancelled and the
oven temperature has cooled.
Stopping or interrupting a self-clean cycle
If it becomes necessary to stop or interrupt a self-
cleaning cycle once it has been activated:
1. Press Clear/Off.
2. Once the oven has cooled down for about 1 HOUR and
the “Door Locked” indicator light has turned off, the oven
door can be opened.
3. Restart the self-clean cycle once all conditions have been
corrected.
Setting a self-clean cycle or a delayed
start self-clean cycle
Setting a self-clean cycle
SELF-CLEANING
NOTE
As soon as the controls are set, the motor driven lock
will begin to close automatically and the “Door Locked”
indicator light will flash. DO NOT open the oven door
while the light is flashing (allow about 15 seconds for the
oven door to lock).
Whenever the self-clean feature is active you may check
the amount of time remaining in the self-clean cycle by
pressing the Clean pad. Remember the range door
cannot be opened until the range has cooled sufficiently.
You will need to add about 1 hour to the time
displayed before you can use the range for cooking.
When the oven is cool, wipe away any residue or
powdered ash with a damp cloth or paper towel.
NOTES
To avoid possible burns use care when opening the oven
door after the self-cleaning cycle. Stand to the side of
the oven when opening the door to allow hot air or
steam to escape.
DO NOT force the oven door open. This can damage the
automatic door locking system. Use caution and avoid
possible burns when opening the door after the self-
cleaning cycle has completed. The oven may still be
VERY HOT.
CAUTION
To start a self-clean cycle immediately without a delay,
skip steps 2 & 3 in the instructions provided below.
IMPORTANT
When the self-clean cycle has completed:
1. The time of day will appear in the display window and
the “Clean” and “Door Locked” indicator lights will
continue to glow.
2. Once the oven has cooled down for about 1 HOUR and
the “Door Locked” indicator light has turned off, the
oven door can be opened.
23
CARE & CLEANING
Surface type Recommendation
•Porcelain enamel broiler pan and broiler
pan insert (if equipped)
•Door liner & body parts
For general cleaning
, use hot, soapy water and a cloth.
For more
difficult soils and built-up grease
, apply a liquid detergent directly onto
the soil. Leave on soil for 30 to 60 minutes. Rinse with a damp cloth
and dry. Do not use abrasive cleaners on any of these materials;
they can scratch. To remove control knobs, turn to the OFF position;
grasp firmly and pull straight off the shaft. To replace knobs after
cleaning, line up the flat sides of both the knob and the shaft; then
push the knob into place.
Before cleaning the control panel,
turn all controls OFF and if needed
remove any knobs from the panel. Clean using hot, soapy water and a
dishcloth. Be sure to
squeeze excess water from the dishcloth
before wiping the control panel; especially when wiping around the
controls area. Excess water in or around the controls may cause
damage to the appliance. When rinsing, use clean water and a
dishcloth and be sure to squeeze excess water from dishcloth before
wiping the control panel.
•Stainless steel (some models)
•Oven racks
•Oven door
Oven racks must be removed from oven cavity. Clean by using
a mild, abrasive cleaner following manufacturer's instructions. Rinse
with clean water and dry. Remove racks from oven during Self-Clean.
Use soap & water to thoroughly clean the top, sides and front of the
oven door. Rinse well. You may use a glass cleaner on the outside
glass of the oven door. Do not immerse the door in water.
Do not
spray or allow water or the glass cleaner to enter the door
vents. Do not use oven cleaners, cleaning powders or any harsh
abrasive cleaning materials on the outside of the oven door.
Do not clean the oven door gasket. On self-cleaning models the oven
door gasket is made of a woven material which is essential for a good
seal. Care should be taken not to rub, damage or remove this gasket.
Do not use spray oven cleaners on the cooktop. See cooktop cleaning
and maintenance in the Care & Cleaning section.
•Ceramic cooktop
Cleaning recommendation table
•Control knobs
•Painted body parts
•Painted decorative trim
•Aluminum, plastic or vinyl trim pieces
•Control panel
•Decorative trim (some models)
Clean heavier soils with hot, soapy water and a dishcloth. Rinse with
clean water and a cloth. Do not use cleaners with high
concentrations of chlorides or chlorine. Do not use harsh scrubbing
cleaners. Only use kitchen cleaners that are especially made for cleaning
stainless steel. Always be sure to rinse the cleaners off from the surface
as bluish stains may occur during heating that cannot be removed.
Gentle scouring with a soapy non-abrasive scouring pad will remove
most spots. Rinse with a 1:1 solution of clear water and ammonia.
If
necessary
, cover difficult spots with an ammonia-soaked paper towel
for 30 to 40 minutes. Rinse with clean water and a damp cloth, and
then scrub with a soap-filled non-abrasive scouring pad. Rinse and
wipe dry with a clean cloth. Remove all cleaners or the porcelain may
become damaged during future heating.
24
Consistent and proper cleaning is essential to
maintaining your ceramic glass cooktop.
Do not:
• Slide anything metal or glass across the cooktop.
• Use cookware with dirt or dirt build up on bottom;
replace with clean cookware before using.
• Use your cooktop as a cutting board or work surface in
the kitchen.
• Cook foods directly on the cooktop surface without a pan.
• Drop heavy or hard objects on the ceramic glass cooktop,
they may cause it to crack.
For light to moderate soil:
Apply a few drops of glass-ceramic cooktop cleaner directly
to the cooktop. Use a paper towel or use a non-abrasive
plastic type no-scratch cleaning pad to clean the entire
cooktop surface. Make sure the cooktop is cleaned
thoroughly, leaving no residue.
For heavy, burned on soil:
Apply a few drops of glass-ceramic cooktop cleaner directly
to the soiled area. Rub the soiled area using a non-abrasive
plastic type no-scratch cleaning pad, applying pressure as
needed. Do not use the pad you use to clean the cooktop
for any other purpose.
If soils remain, carefully scrape soils with a metal razor
blade scraper, holding scraper at a 30 degree angle to the
surface. Remove loosened soils with cooktop cleaning
cream and buff surface clean.
Prior to using your cooktop for the first time, apply some of
the glass-ceramic cooktop cleaner supplied with your new
appliance. Buff with a non-abrasive cloth or no-scratch
cleaning pad. This will make cleaning easier when soiled
from cooking. The special cooktop cleaning cream leaves a
protective finish on the glass to help prevent scratches and
abrasions.
Sliding aluminum or copper clad bottom pans on the
cooktop can cause metal markings on the cooktop surface.
These marks should be removed immediately after the
cooktop has cooled using the cooktop cleaning cream. Metal
marks can become permanent if not removed prior to
future use.
Cookware (cast iron, metal, ceramic or glass) with rough or
dirty bottoms can mark or scratch the cooktop surface.
Before cleaning the cooktop, be sure the controls are
turned to OFF and the cooktop is COOL.
Cooktop maintenance Cooktop cleaning
IMPORTANT
CAUTION
CARE & CLEANING
30°
Plastic or foods with a high sugar content:
These types of soils need be removed immediately if spilled
or melted onto the ceramic cooktop surface. Permanent
damage (such as pitting of the cooktop surface) may occur
if not removed immediately. After turning the surface
elements OFF, use a razor blade scraper or a metal spatula
with a mitt and scrape the soil from the hot surface (as
illustrated). Allow the cooktop to cool, and use the same
method for heavy or burned on soils.
DO NOT use a cooktop cleaner on a hot cooktop.
The fumes can be hazardous to your health and
can chemically damage the ceramic glass surface.
WARNING
25
CARE & CLEANING
Damage to the ceramic glass cooktop may occur if you
use an abrasive type cleaning pad. Only use cleaning
products that have been specifically designed for ceramic
glass cooktops.
Caution for aluminum use on the cooktop
•Aluminum Foil - Use of aluminum foil on a hot cooktop
will damage the ceramic cooktop. Do not use thin
aluminum cooking utensils or allow aluminum foil to
touch the ceramic cooktop under ANY circumstances.
•Aluminum utensils - The melting point of aluminum
is much lower than that of other metals. Care must be
taken when aluminum pots or pans are used on the
cooktop. If aluminum pans are allowed to boil dry
when using the cooktop, not only will the utensil be
damaged or destroyed, but it may fuse to, break or
mark the ceramic glass surface, permanently
damaging the cooktop surface.
Do not use the following on the cooktop:
• Do not use abrasive cleaners and scouring pads, such as
metal and some nylon pads. They may scratch the
cooktop, making it more difficult to clean.
• Do not use harsh cleaners, such as chlorine bleach,
ammonia or oven cleaners, as they may etch or discolor
the cooktop.
• Do not use dirty sponges, cloths or paper towels, as they
can leave soil or lint on the cooktop which can burn and
cause discoloration.
Cooktop cleaning (cont’d)
IMPORTANT
Replacing the oven light
The light bulb is located at the rear of the oven and is
covered with a glass shield held by a wire holder. The glass
shield must be in place whenever the oven is in use.
To replace the interior oven light bulb
1. Turn electrical power off at the main source or unplug
the range.
2. Open oven door for access to interior oven light. Once
located, press wire holder to one side to release the
glass shield (See Fig. 1).
3. Replace bulb with a new 40 watt appliance bulb.
4. Replace glass shield over bulb and snap wire holder into
place.
5. Turn power back on again at the main source (or plug
the range back in).
6. The clock will then need to be set with the correct time
of day. To reset, see “Setting the Clock” in this Use &
Care Guide.
wire holder
glass shield
Be sure the range is unplugged and all parts are COOL before
replacing oven light. Wear a leather-faced glove for protection
against possible broken glass.
CAUTION
Fig.1
26
To remove oven door:
1. Open oven door completely (horizontal with floor - See
Fig. 1).
2. Pull the door hinge locks on both left and right door
hinges down from the oven frame completely towards
the oven door (See Fig. 2). A tool such as a small flat-
blade screwdriver may be required.
3. Firmly grasp both sides of oven door along the door
sides (Do not use the oven door handle - See Fig. 3).
4. Close the door to the broil stop position (the oven door
will stop into this position just before fully closing).
5. With the oven door in the broil stop position, lift the oven
door hinge arms over the roller pins located on each side
of the oven frame (See Fig. 4).
To replace oven door:
1. Firmly grasp both sides of oven door along the door
sides (Do not use the oven door handle - See Fig. 3).
2. Holding the oven door at the same angle as the removal
position, seat the hook of the hinge arm over the roller
pins located on each side of the oven door frame (See
Fig. 4). The hook of the hinge arms must be fully seated
onto the roller pins.
3. Fully open the oven door (horizontal with floor - See Fig.
1).
4. Push the door hinge locks up towards and into the oven
frame on both left and right oven door hinges (See Fig.
2) to the locked position.
5. Close the oven door.
Special door care instructions - Most oven doors
contain glass that can break.
Read the following recommendations:
1. Do not close the oven door until all the oven racks are
fully in place.
2. Do not hit the glass with pots, pans, or any other object.
3. Scratching, hitting, jarring or stressing the glass may
weaken its structure causing an increased risk of
breakage at a later time.
Removing and replacing the lift-off oven door
Fig. 3
Oven door
hinge
locations
with oven door
fully open.
Fig. 1
Fig. 2
Fig. 4
CARE & CLEANING
CAUTION
• To avoid possible injury when removing or
replacing the oven door, follow the instructions below
carefully and always hold the oven door with both
hands positioned away from the door hinge area
(See Fig. 3).
•The door is heavy. For safe, temporary storage, lay
the door flat with the inside of the door facing down.
27
BEFORE YOU CALL • Solutions to common problems
Surface element does not heat.
Entire appliance does not operate. • The time of day is not set. The time of day must first be set in order to
operate the oven. See “Setting the clock” in the Setting oven controls
section.
• Make sure cord/plug is plugged correctly into outlet.
• Service wiring is not complete. Contact your dealer, installing agent or
authorized service agent.
• Electrical power outage. Check house lights to be sure. Call your local
electric company for service.
• Be sure the oven controls are set properly for the desired cooking feature.
See Setting Oven Controls in this manual or read the instructions “Entire
appliance does not operate” in this checklist.
Oven light does not work.
• Lightweight or warped pans used. Use only flat, evenly balanced, medium
or heavyweight cookware. Flat pans heat better than warped pans.
Cookware materials and weight of the material affect heating. Heavy &
medium-weight pans heat evenly. Because lightweight pans heat unevenly,
foods may burn easily.
Cannot move appliance easily. Appliance
must be accessible for service.
• Cabinets not square or are built in too tightly. Contact builder or installer to
make appliance accessible.
• Carpet interferes with appliance. Provide sufficient space so appliance can be
lifted over carpet.
Surface element too hot or not hot
enough.
• Incorrect control setting. Be sure the correct control is ON for the element that
you are attempting to use.
Problem Solution
Appliance is not level. • Be sure floor is level, strong & stable enough to adequately support range.
• If floor is sagging or sloping, contact a carpenter to correct the situation.
• Poor installation. Place oven rack in center of oven. Place a level on the
oven rack. Adjust leveling legs at base of appliance until the rack is level.
• Kitchen cabinet alignment may make range appear not level. Be sure
cabinets are square & have sufficient room for appliance clearance.
• Be sure the light is secure in the socket. Also see “Changing & replacing the
oven light” section.
Poor baking results. • Many factors affect baking results. Make sure the proper oven rack position
is used. Center food in the oven and space pans to allow air to circulate.
Allow the oven to preheat to the set temperature before placing food in the
oven. Try adjusting the recipe's recommended temperature or baking time.
If you feel the oven is too hot or cool, see “Adjusting Oven Temperature”
section in this Use & Care Guide.
Oven portion of appliance does not
operate.
Self-clean cycle does not work.
• Self-clean cycle was interrupted. Follow steps under "Stopping or
Interrupting a Self-cleaning cycle" under Self-Clean.
• Oven control not set properly. Follow instructions under Self-Clean.
Produkt Specifikationer
| Mærke: | Crosley |
| Kategori: | Komfur |
| Model: | CRE3895PS |
Har du brug for hjælp?
Hvis du har brug for hjælp til Crosley CRE3895PS stil et spørgsmål nedenfor, og andre brugere vil svare dig
Komfur Crosley Manualer
3 Juli 2025
16 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
Komfur Manualer
- Orbegozo
- Vitrokitchen
- Concept
- Premium
- Soler & Palau
- Termozeta
- Elba
- Lamona
- Tefal
- PKM
- Neff
- LERAN
- Leonard
- MaxxHome
- Coleman
Nyeste Komfur Manualer
11 August 2025
10 August 2025
10 August 2025
10 August 2025
10 August 2025
10 August 2025
10 August 2025
10 August 2025
9 August 2025
9 August 2025