CTA Digital ADD-AUTSAM Manual

CTA Digital Ikke kategoriseret ADD-AUTSAM

Læs gratis den danske manual til CTA Digital ADD-AUTSAM (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om CTA Digital ADD-AUTSAM, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

ADD-AUTSAM

Package Contents:

AMPS Mounting Base for Vehicles w/ VESA Plate

1.Connecting VESA Plate to the Pole Body

1. Put a plastic washer on the top of

the Pole and then insert it into the

VESA Plate.

2. Place a plastic washer then a metal washer

over the Pole tip, screw nut over to lock

in place.

3. Use the Socket Wrench to tigten it securely.

Instructions:

4. Adjusting Joints

1. Loosen the Handle Rod of the Pole,Adjust the Pole to desired position

then tighten the Handle Rod.

2. Rotate the VESA Plate to adjust it in horizontal.

“Y ” Screws

Wall Screws

2. Attaching Car Seat Rail Clamp to Multi-Flex Pole.

These three clamps allow you to connect from the bottom of Multi-Flex Pole.

Depending on your car or vehicle, you may need to choose the diffrent car seat rail clamp according to your needs.

Allen Key

Spring Washer

Metal Washer

Screw

Y Screw

1. Choose the base with the angle

that matches your needs.

Seat Rail Connection Bases

3. Screw a Y screw into hole on

the base of the multi-flex arm to

prevent rotation.

2. Align washers and base as shown

Use Allen key to screw together.

3. Installing to Your Car

These four clamps allow you to connect it to the car seat rail.

2.Insert c seat ar rail clamp . 1.With a socket wrench,

loosen car seat rail bolt

3.Retighten car seat

rail bolt.

These two clamps allow you to connect the side of the Multi-flex pole

Y Screw

Use this piece if you need to attach

the gooseneck to the side of your

seat rail (instead of directly above)

1. Align the holes on the clamp

to the screw holes on the side

of the gooseneck.

2. Use 2 Y screws to tighten

connection to pole.

This clamp allow you to connect it to the car floor or console.

Hole Diameter: 4.5 mm

For permanent installation, connect the Multi-Flex

Security Car Mountto the flooror console. This will

require drilling into your vehicle’s interior surface.

Drilling into the dash, floor, or console

will permanently damage the vehicle.

Use caution and consult a mobile install

professional to avoid drilling into the

gas tank,electrical system or other

highly sensitive vehicle components.

2.Screw up the clamp

to floor or concole

of the car.

1.Make holes on the floor or

console of the car according to

the holes you selected on the

clamp.

Socket Wrench

Nut

Metal Washer

Wear-resistant Washer

Spring Washer

Metal Washer

Screw

Wear-resistant Washer

VESA Plate

Allen Key

Plastic Washer

Metal Lock Nut

Plastic

Washer

Metal Washer

Produkt Specifikationer

Mærke:	CTA Digital
Kategori:	Ikke kategoriseret
Model:	ADD-AUTSAM
Bredde:	127 mm
Højde:	596 mm
Vægt:	850 g
Antal pr. pakke:	1 stk
Produktfarve:	Sort
VESA montering:	Ja
Normal brug:	Bil
Rotationsvinkel:	360 °
Forbedret kabelstyring:	Ja
Mobil enhedstype:	Laptop, Tablet/UMPC
Orientering:	Horisontal/vertikal
Beslagtype til enhed:	Skruebeslag
Montering interface kompatibilitet (maks.):	100 x 100 mm