CTA Digital PAD-AFS Manual

CTA Digital Ikke kategoriseret PAD-AFS

Læs gratis den danske manual til CTA Digital PAD-AFS (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 11 anmeldelser. Har du et spørgsmål om CTA Digital PAD-AFS, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Select the appropriate foam pad according to the thickness of

your tablet (or tablet in its case), then press adhesive side into

center of the tablet holder.

Use this table to determine the appropriate foam pad to

use with your tablet.

Note: sizes refer to total tablet size with or without a case.

Foam Pad

Thickness

1mm

5mm

10mm

Tablet Thickness

0.51-0.91in / 13-23mm

0.31-0.71in / 8-18mm

0.67-1.06in / 17-27mm

1mm Foam Pad

5mm

Foam

Pad

10mm

Foam

Pad

1).Attaching Foam Pad to Tablet Holder

PAD-AFS

SUPPORT@CTADIGITAL.COM

Gooseneck flexes by hand.To adjust the height of the pole,

turn plastic cover counter-clockwise and raise or lower the pole

to desired height. Turn clockwise again to lock it in place.

Allen Key

360 rotation

270 rotation

Multi

direction

flexing

Use the Allen key to tighten and loosen the

gooseneck connection screw, adjusting ease of

rotation in the tablet holder.

5.Adjustment:

4. Connecting the Tablet Holder to the Pole and Installing Your Device

Press button on side of tablet holder to

slide open. Insert your tablet against

spring arm,then slide other end back

down.

Screw the gooseneck onto the metal

connection of the pole by turning

clockwise.

Turn the Y screw clockwise to tighten

the connection.

Note: if Y screw is already in,

unscrew before attaching gooseneck.

Gooseneck

Metal Connection

Y Screw

Instructions:

2. Base Assembly and Connecting the Metal Cover:

METAL CONNECTION

HEIGHT

ADJUSTMENT

KNOB

POLE

METAL

CROSS BASE X 2

CONNECTION SCREW BOLT,

WASHERS AND NUT

Pole Assembly and Pole Nut

Cross Base Sections (2)

Allen Key

4. Rotate the grip counter clockwise to

loosen completely and remove from top

of pole.

5. Place the square metal cover over

the top of the pole and slide down to

stand base.

6. Place grip back over stand pole

and tighten.

3. Connecting the Stand to the Floor (Optional)

1. Use a pencil to mark holes on the

floor aligned with holes in the stand,

then drill. If using plastic inserts,hole

diameter should be around 8mm.

If not using plastic inserts,hole

diameter should be around 5.5mm.

Without plastic insert

Use the plastic insert

2. Put a floor screw through a

washer and align with hole,

then use the Allen key to screw

into the floor.

2. Put a plastic insert

into the floor hole. Put a screw

through a washer and align

with hole, then use Allen key

to screw into the floor.

3. Repeat step 2 for remaining holes.

1). Place the metal base pieces with the higher piece on top of the cross base. Align the holes at the bottom of the pole with

the holes on the cross base.

2). Insert a screw bolt with a washer into each of 4 holes. Place another washer on the underside of each screw bolts.

3). Grip the nut on the underside with one hand,and use the other to tighten each screw with Allen key. Repeat to tighten all

four screw bolts.

Package Contents:

Floor Screw

Plastic Inserts

Washer

Produkt Specifikationer

Mærke:	CTA Digital
Kategori:	Ikke kategoriseret
Model:	PAD-AFS
Produktfarve:	Sort, sølv
Pakkevægt:	2041 g
Pakkedybde:	106.172 mm
Pakkebredde:	198.755 mm
Pakkehøjde:	622.3 mm
Indbyggede højttaler(e):	Ingen
Materiale:	ABS synthetics, Steel
Strømkilde type:	Ikke understøttet
Monteringstype:	Gulv
Normal brug:	Indendørs
Kapabilitet:	iPad 2nd – 4th Gen
Rotationsvinkel:	360 °
Højdejusteringsområde:	1066.8 - 1402.08 mm
Justerbar:	Ja
Mobil enhedstype:	Tablet/UMPC