CyberPower RB1290X16 Manual

CyberPower Batteri RB1290X16

Læs gratis den danske manual til CyberPower RB1290X16 (3 sider) i kategorien Batteri. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 18 anmeldelser. Har du et spørgsmål om CyberPower RB1290X16, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

1 2 3

123

MODEL: OR1500LCDRM2U, OR2200LCDRM2U, OR1500LCDRTXL2U,

MODEL: PR1000LCD

MODEL: PR1500LCD

1. Remove the front panel of the UPS.

2. Remove two screws from the battery compartment cover and slide the cover completely off of

the unit.

3. Remove the batteries from the compartment. Disconnect the battery wires from the batteries.

4. Install the replacement batteries by connecting the wire bundle (composed of one red wire and

one black wire) to the connector from the battery pack.

5. Put the batteries back into the compartment. Re-install the battery compartment cover and

tighten the retaining screws. Put the front panel back on the UPS.

6. Connect to AC power and charge the new batteries for up to 16 hours to insure a full charge

MODEL: PR750LCDRM1U, PR1000LCDRM1U

1. Remove the right side front panel.

2. Remove the two retaining screws for the cable protection cover and remove the cover.

3. Disconnect the black and red cable.

4. Remove the one retaining screw holding the battery pack in place.

5. Remove the battery pack.

6. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse

sequence of the above steps. Charge the unit for 4-8 hours to ensure the UPS performs expected

runtimes.

MODEL: PR1500SWRM2U, PR2200SWRM2U

1. Remove the right side front panel.

2. Remove the two retaining screws for the cable protection cover and remove the cover.

3. Disconnect the black and red cable.

4. Remove the four retaining screws holding the battery pack in place.

5. Remove the battery pack.

6. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse

order of the previous steps. Charge the unit for 4-8 hours to ensure the UPS performs expected

runtimes.

MODEL: PR1000LCDRT2U, PR1000LCDRTXL2U, PR1500LCDRT2U,

PR2200LCDRT2U, PR3000SWRM2U

1. Remove the right side front panel.

2. Remove the three retaining screws for the cable protection cover and remove the cover.

3. Remove the two retaining screws from the cable connectors.

4. Disconnect the black and red cable.

5. Remove the four retaining screws holding the battery pack in place.

6. Remove the battery pack.

7. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse

order of the previous steps. Charge the unit for 4-8 hours to ensure the UPS performs expected

runtimes.

MODEL: PR1000LCDRTXL2Ua, PR1500LCDRTXL2U, PR2200LCDRTXL2U,

PR3000LCDRT2U, PR3000LCDRTXL2Umart

1. Remove the six retaining screws, and remove the front panel from the UPS.

2. Remove the two retaining screws for the cable protection cover and remove the cover.

3. Remove the two retaining screws from the cable connectors.

4. Disconnect the black and red cable.

5. Remove the three retaining screws holding the battery pack in place.

6. Remove the battery pack.

7. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse

order of the previous steps. Charge the unit for 4-8 hours to ensure the UPS performs expected

runtimes.

MODEL: PR5000LCDRTXL5U, PR6000LCDRTXL5U

1. Remove the front panel.

2. Remove the two retaining screws of the cable protection cover and remove the cover.

3. Pull the plastic sticker out slowly to remove the battery module.

4. Put the new battery modules back into the compartment.

5. Tighten the screws and replace the cable protection cover and the front panel.

PFC SINEWAVE Series

MODEL: CP850PFCLCD, CP1000PFCLCD

1. Turn the UPS on its side. Remove the retaining screw located on the bottom of the UPS.

2. Slide the battery compartment cover completely off of the unit.

3. Remove the batteries from the compartment.

4. Disconnect the battery wires from the batteries.

5. Install the replacement batteries by connecting the red wire (+) and black wire (-) to the same

color connectors from the battery pack. Put the batteries back into the compartment.

6. Slide back the battery compartment cover and tighten the retaining screw. Recharge the UPS

Produkt Specifikationer

Mærke:	CyberPower
Kategori:	Batteri
Model:	RB1290X16
Bredde:	540 mm
Dybde:	400 mm
Højde:	378 mm
Vægt:	49305 g
Batterispænding:	12 V
Batterikapacitet:	9000 mAh
Pakkevægt:	4132625 g
Pakkedybde:	330 mm
Pakkebredde:	642 mm
Pakkehøjde:	393 mm
Batteriteknologi:	Blybatterier (VRLA)
Relativ luftfugtighed ved drift (H-H):	0 - 90 %
Driftstemperatur (T-T):	0 - 40 °C
Numre af batterier medfølger:	16 stk
Kompatible produkter:	PR5000LCDRTXL5U, PR6000LCDRTXL5U
Kapabilitet:	PR5000LCDRTXL5U, PR6000LCDRTXL5U