DeWalt DW744XCDN Manual

DeWalt Sav DW744XCDN

Læs gratis den danske manual til DeWalt DW744XCDN (2 sider) i kategorien Sav. Denne vejledning er vurderet som hjælpsom af 38 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 19.5 anmeldelser. Har du et spørgsmål om DeWalt DW744XCDN, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

OPENING

OUVERTURE

ABERTURA

TAB

LANGUETTE

LENGÜETA

FIG. 2

FIG. 3

FIG. 1

FIG. 4

WARNING

AVERTISSEMENTADVERTENCIA

TO REDUCE THE RISK OF INJURY, READ AND

UNDERSTAND THE TOOL STAND INSTRUCTION SHEET

AND THE TOOL INSTRUCTION MANUAL BEFORE USE. FOR USE WITH DW744 TABLE

SAW ONLY. ENGAGE TOOL IN STAND AND OPEN FULLY BEFORE USE. MAXIMUM LOAD

EQUALS 150 LBS. (68KG). DO NOT CLIMB, SIT OR STAND ON SAW STAND. DO NOT USE

ON SLOPED, UNEVEN OR UNSTABLE SURFACES. USE ONLY FROM THIS SIDE.

PARA REDUCIR EL RIESGO DE LESIÓN, LEA Y ENTIENDA LA HOJA DE

INSTRUCCIÓN DEL SOPORTE DE LA HERRAMIENTA Y EL MANUAL DE

INSTRUCCIÓN DE LA HERRAMIENTA ANTES DE USO. PARA EL USO CON LA SIERRA DE LA TABLA DW744

SOLAMENTE. COLOQUE LA HERRAMIENTA EN LA BASE

Y ÁBRASE COMPLETAMENTE ANTES DE USO. LA CARGA

MÁXIMA IGUALA 150 LIBRAS. (68KG). NO SUBA, NO SE SIENTE NI ESTÉ PARADO EN SOPORTE DE LA SIERRA. NO

UTILICE EN SUPERFICIES INCLINADAS, DESIGUALES O INESTABLES. UTILICE SOLAMENTE DE ESTE LADO.

POUR RÉDUIRE LE RISQUE DE DOMMAGES, LISEZ ET COMPRENEZ LA FEUILLE

D'INSTRUCTION DE STAND D'OUTIL ET LE MANUEL D'INSTRUCTION D'OUTIL AVANT

L'EMPLOI. POUR L'USAGE AVEC LA SCIE DU TABLEAU DW744 SEULEMENT. ENGAGER L’OUTIL DANS LE SOCLE ET OUVREZ-VOUS

ENTIÈREMENT AVANT L'EMPLOI. LA CHARGE MAXIMUM ÉGALE 150 LIVRES. (68KG). NE VOUS ÉLEVEZ PAS, NE VOUS REPOSEZ PAS OU

NE VOUS TENEZ PAS SUR LE STAND DE SCIE. N'EMPLOYEZ PAS SUR LES SURFACES INCLINÉES, INÉGALES OU INSTABLES. EMPLOYEZ

SEULEMENT DE CE CÔTÉ. MADE IN CHINA/HECHO EN CHINA/FABRIQUÉ EN CHINE

FIG. 5

Heavy Duty Table Saw Stand DW7440

WARNING: For your own safety, read the table saw instruction

manual before using any accessory. Failure to heed these

warnings may result in personal injury and serious damage to the

table saw and the accessory. When servicing this tool, use only

identical replacement parts.

• This table saw stand is designed only for use with the DW744

and DW744X table saws. Do not use this stand with any other

tool.

• Do NOT mount the table saw to the stand in any other

orientation.

• Feet should be assembled to the end of the legs as shown.

• Position all of the feet in the same orientation or unstable footing

may occur.

• Open saw stand fully before use.

• Maximum load: 150 lbs. (68kg.)

• Do not climb on or sit on saw stand.

• Do not use saw stand on inclined, uneven or unstable

surfaces.

• The back legs of the saw stand are slightly longer than the

front legs to provide additional support. Use the saw stand and

operate the table saw from the front side only.

• Do not use saw stand if it is damaged or bent.

SAVE THESE INSTRUCTIONS

ASSEMBLY

• Assemble as shown in Figure 1.

TO OPEN TABLE SAW STAND

1. Unfold the saw stand until it is fully opened. Place it upright, as

shown in Figure 2.

2. Place the table saw on the saw stand. Place the tabs on the

front of the table saw into the openings on the front of the saw

stand, as shown in Figure 3. Ensure the tabs fit snugly into the

openings. Be sure that the rear of the base is resting on the

lower step of the frame (Fig. 4) and does not rock or wobble in

place. DO NOT mount the table saw to the saw stand in any

other orientation.

TO CLOSE TABLE SAW STAND

1. Lift the table saw from the saw stand.

2. Pick the stand up by the top rails and close it.

CAUTION: Be sure the saw is mounted firmly to your stand before

using it.

FREE WARNING LABEL REPLACEMENT: If your warning labels

(Fig. 5) become illegible or are missing, call 1-800-4-DEWALT for a

free replacement.

The following are trademarks for one or more DeWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids

on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.