Digital Watchdog MegaPix DWC-MB45IALPRT Manual

Digital Watchdog Overvågningskamera MegaPix DWC-MB45IALPRT

Læs gratis den danske manual til Digital Watchdog MegaPix DWC-MB45IALPRT (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Digital Watchdog MegaPix DWC-MB45IALPRT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

THE CAPTURED IMAGE SHOULD BE FILLED WITH THE FULL WIDTH OF THE VEHICLES

THE CAMERA SHOULD BE MOUNTED AT AN ANGLE NO GREATER THAN 30 DEGREES

CAMERA ANGLE NO GREATER THAN 20 DEGREES FOR SIDE MOUNT INSTALLATIONS

>11.5ft

< 30°

< 20°

Quick Start Guide

Tel: +1 (866) 446-3595 / (813) 888-9555

Technical Support Hours:

9:00 AM – 8:00 PM EST, Monday through Friday

digital-watchdog.com

Attention: This document is intended to serve as a quick reference for initial

set-up. It is recommended that the user read the entire instruction manual for

complete and proper installation and usage.

NOTE: Download all your support materials and tools in one place

1. Go to: http://www.digital-watchdog.com/resources

2. Search your product by entering the part number in the

search bar. Results for applicable ‘Search by Product’

part numbers will populate automatically based on the

part number you enter.

3. Click ‘Search’. All supported materials, including manuals

and quick start guide (QSGs) will appear in the results.

DWC-MB45iALPRT

WHAT’S IN THE BOX

Quick setup

and installation

guide

Screws and

plastic

anchors – 4pcs

1 set

Mounting

template 1Hex Allen

wrench 1

Test video cable 1 Waterproof cap 1 set

LPR INSTALLATION GUIDELINES

Resetting the camera: To reset the camera, use the tip of a

paper clip or a pencil and press the reset button. Pressing the

button for ﬁve (5) seconds will initiate a camera-wide reset of

all the settings, including network settings.

Quick Start Guide

1. Once all cables are connected, secure the camera to the mounting

surface using the included screws.

2. To use the camera’s waterproof wiring:

a. Install the LAN cable into .

b. will be assembled to with a 1/4 turn.

c. Thread tightly to .

3. Loosen the pan and tilt screws at the base of the camera’s bracket to

adjust the camera’s view and position.

STEP 1 – PREPARING TO MOUNT THE CAMERA

STEP 2 – CABLING THE CAMERA TO

EXTERNAL DEVICES

Pass the wires through and make all necessary

connections. See STEP 4.

1. NETWORK CONNECTIONS – Using a PoE Switch or

PoE Injector, connect the camera using an Ethernet

cable for both data and power.

2. NETWORK CONNECTIONS – Not using PoE Switch

or PoE Injector, connect the camera to the switch

using an Ethernet cable for data transmission and

use a power adapter to power the camera.

Power requirements Power consumption

DC12V, PoE

(IEEE 802.3af class 3).

Adapter not Included.

DC12V Max 9W

PoE Max 10.5W

STEP 3 – INSTALLING THE CAMERA

NOTE: When using the waterproof cap, crimp the RJ45

connector after passing the cable through the

waterproof cap.

1. The mounting surface must bear ﬁve times the weight of

your camera.

2. Do not let the cables get caught in improper places or the electric line

cover to be damaged. This may cause a breakdown or ﬁre.

3. Using the mounting template sheet or the camera itself, mark and

drill the necessary holes in the wall or ceiling.

Reset button

Zoom lens

button

SD card

input

Default Login Information: admin | admin

When logging into the camera for the ﬁrst time, you will be prompted

to set up a new password. You can set the new password using the

DW® IP Finder™ software or directly from the camera’s browser menu.

Rev Date: 04/20

Speciﬁcations and pricing are subject to change without notice.

Quick Start Guide

STEP 6 – DW IP FINDER™

Thumbnail view

Firmware version

Camera’s uptime

Open Device

conﬁguration

settings

Filter device type to scan

Scan devices

Select network to scan

Show/hide thumbnail view

Refresh thumbnail view

Bulk IP assignment

Firmware upgrade

Device’s

information

Use the DW IP Finder™ software to scan the network and detect all MEGApix® cameras, set the camera’s network settings or access the camera’s web client.

STEP 4 – CABLING

STEP 5 – MANAGING THE SD CARD

Use the diagram below to properly connect power, network, audio, alarm

and sensors to the camera.

1. To install the camera’s SD Card, locate the SD card slot at the

bottom of the camera by unscrewing the con cap.

2. Insert class 10 SD/SDHC/SDXC card into the SD card slot by

pressing the SD card until clicks.

3. To remove the SD card, press the card inward until it clicks to

release from the card slot then pull out from the slot.

NOTE: Maximum SD Card size supported: 64GB.

When inserting the SD card into the card slot, the SD

card’s contacts should be facing upward, as shown in

the diagram.

Network Setup

1. To install the DW IP Finder™, go to:

http://www.digital-watchdog.com

2. Enter “DW IP Finder” on the search box at the top of the page

and press Enter.

3. Click on the DW IP Finder from the search result and go to the

Software tab. Click on the download icon to download the DW

IP Finder installation ﬁle.

4. Run the installation ﬁle and follow the wizard to install the DW

IP Finder™. Open the DW IP Finder™ and click ‘Scan Devices’. It

will scan the selected network for all supported devices and list

the results in the table. During the scan, the DW logo will

turn gray.

Default ID / PW : admin / admin

‘Port forwarding’ has to be set in your

network’s router for external access

to the camera.

*NOTE: For security purposes, it is highly

recommended to change your

password after initial setup.

Default TCP/IP information: DHCP

Select DHCP if the internet service is dynamic IP. This will allow the

camera to receive its IP address from the DHCP server.

Select “Static” to manually enter the camera’s IP address, (Sub)

Netmask, Gateway and DNS information.

* The camera’s IP must be set to Static if connecting to

DW Spectrum

Contact your network administrator for more information.

5. Select a camera from the list by double-clicking on the

camera’s image or click on the ‘Click’ button under the IP Conf.

column. The pop-up window will show the camera’s current

network settings, allowing admin users to adjust the settings as

needed.

6. To access the camera’s web page, click on ‘View

Camera Website’.

7. To save the changes made to the

camera’s setting, input the username

and password of the camera and click

Apply. Click “Scan Devices” from the

main screen again to display the

updated information.

1 Power

2 Network

4 Audio

Output

3 Audio

Input

5 Alarm

Output

N.C

N.O I n 1

COM

In 1

COM

In 1

COM

In 1

COM

6 Alarm Input

STEP 7 – WEB VIEWER

The GUI display may dier by camera models.

NOTE: Please see the full product manual for web viewer setup,

functions and camera settings options.

* NOTE: Some menu options may not be available based on the

camera model. See the full manual for more information.

Once the camera’s network settings have been setup properly, you can

access the camera’s web viewer using the DW IP Finder® ™.

To open the camera’s web viewer:

1. Find the camera using the DW® IP Finder™.

2. Double-click on the camera’s view in the results table.

3. Press the ‘View Camera Website’. The camera’s web viewer will

open up in your default web browser.

4. Enter the camera’s username and password you setup in the DW®

IP Finder™. If you did not setup a new username and password via

the DW® IP Finder™, you will not be able to view video from the

camera. A message will direct you to setup a new password for the

camera in order to view video.

5. When accessing the camera for the ﬁrst time, install the VLC player

for web ﬁles in order to view video from the camera.

NOTE: 32bit version of VLC player must to be installed. If you are

using 64bit system, uninstall the previous 64bit version and

reinstall using the 32bit version.

Produkt Specifikationer

Mærke:	Digital Watchdog
Kategori:	Overvågningskamera
Model:	MegaPix DWC-MB45IALPRT

Har du brug for hjælp?

Hvis du har brug for hjælp til Digital Watchdog MegaPix DWC-MB45IALPRT stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Overvågningskamera Digital Watchdog Manualer

Digital Watchdog MegaPix DWC-MB95WI Manual

1 December 2024

Digital Watchdog MEGApix DWC-MV72DI Manual

1 December 2024

Digital Watchdog MEGApix DWC-MPF2WI Manual

1 December 2024

Digital Watchdog MEGApix DWC-MF2WI Manual

1 December 2024

Digital Watchdog Star-Light DWC-D3263TIR Manual

1 December 2024

Digital Watchdog DWC-B6263WTIR 2.1MP Outdoor Universal HD Analog Bullet Camera wit Manual

1 December 2024

Digital Watchdog MEGApix CaaS DWC-MB44WIAWC Manual

30 November 2024

Digital Watchdog MegaPix DWC-MVA2WiAT Manual

30 November 2024

Digital Watchdog MegaPix CaaS DWC-MB44WI650C6 Manual

30 November 2024

Digital Watchdog MegaPix DWC-MV72WI4A Manual

30 November 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

Arecont Vision MicroDome G2 AV2555DN-F-NL Manual

17 Juni 2025

Arecont Vision SurroundVideo G5 Mini AV20CPD-118 Manual

17 Juni 2025

Arecont Vision MicroDome Duo AV10956DN-28 Manual

17 Juni 2025

Arecont Vision SurroundVideo Omni SX AV12275DN-NL Manual

17 Juni 2025

Arecont Vision MicroDome G2 AV3556DNIR-S-NL Manual

17 Juni 2025

Axis Q3548-LVE Manual

17 Juni 2025

Arecont Vision MicroDome Duo AV4656DN-08 Manual

17 Juni 2025

Arecont Vision MicroDome G2 AV5856DNIR-F Manual

17 Juni 2025

Arecont Vision ConteraIP Omni LX AV20476DN-NL Manual

17 Juni 2025

Arecont Vision MicroDome G2 AV5756DNIR-S Manual

17 Juni 2025