Digital Watchdog MegaPix IVA+ DWC-MPB45WIAT Manual

Digital Watchdog Overvågningskamera MegaPix IVA+ DWC-MPB45WIAT

Læs gratis den danske manual til Digital Watchdog MegaPix IVA+ DWC-MPB45WIAT (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Digital Watchdog MegaPix IVA+ DWC-MPB45WIAT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Quick Start Guide

Tel: +1 (866) 446-3595 / (813) 888-9555

Technical Support Hours:

9:00 AM – 8:00 PM EST, Monday through Friday

digital-watchdog.com

Attention: This document is intended to serve as a quick reference for the

initial setup. It is recommended that the user read the entire instruction manual

for complete and proper installation and usage.

NOTE: Download all your support materials and tools in one place

1. Go to: http://www.digital-watchdog.com/resources

2. Search your product by entering the part number in the

search bar. Results for applicable ‘Search by Product’

part numbers will populate automatically based on the

part number you enter.

3. Click ‘Search’. All supported materials, including manuals

and quick start guide (QSGs) will appear in the results.

1. Once all cables are connected, secure the camera to the mounting

surface using the included screws.

2. To use the camera’s waterproof wiring:

a. Install the LAN cable into .

b. will be assembled to with a 1/4 turn.

c. Thread tightly to .

3. Loosen the pan and tilt screws at the base of the camera’s bracket to

adjust the camera’s view and position.

STEP 1 – PREPARING TO MOUNT THE CAMERA

STEP 2 – POWERING THE CAMERA

Power requirements Power consumption

DC12V, PoE

(IEEE 802.3af class 3).

Adapter not Included.

DC12V Max 9W

PoE Max 10.5W

STEP 3 – INSTALLING THE CAMERA

NOTE: To ensure moisture seal, make sure the o-ring is in place

between and . In extreme environments use of an

outdoor rated sealer is recommended.

NOTE: When using the waterproof cap, crimp the RJ45

connector after passing the cable through the

waterproof cap.

Resetting the camera: To reset the camera, use the tip of a

paper clip or a pencil and press the reset button. Pressing the

button for ﬁve (5) seconds will initiate a camera-wide reset of

all the settings, including network settings.

1. The mounting surface must bear ﬁve times the weight of

your camera.

2. Do not let the cables get caught in improper places or the electric line

cover to be damaged. This may cause a breakdown or ﬁre.

3. CAUTION: These servicing instructions are for use by qualiﬁed service

personnel only. To reduce the risk of electric shock do not perform

any servicing other than that contained in the operating instructions

unless you are qualiﬁed to do so.

4. This product is intended to be supplied by a UL Listed Power Supply

Unit marked “Class 2” or “LPS” or “PS2” and rated 12 Vdc, 0.75A min.

5. The wired LAN hub providing power over the Ethernet (PoE) in

accordance with IEEE 802-3af shall be a UL Listed device with the

output evaluated as a Limited Power Source as deﬁned in UL60950-1

or PS2 as deﬁned in UL62368-1.

6. Unit is intended for installation in a Network Environment 0 as deﬁned

in IEC TR 62102. As such, associated Ethernet wiring shall be limited

to inside the building.

7. Using the mounting template sheet or the camera itself, mark and

drill the necessary holes in the wall or ceiling.

MEGApix® IVA+™ models 5MP models

DWC-MPB45Wi650T DWC-MB45Wi650T

DWC-MPB45WiAT DWC-MB45WiAT

WHAT’S IN THE BOX

Quick Setup and

Download Guide 1 set

Screws and

Plastic

Anchors – 4pcs

1 set

Mounting

Template 1 1Star Wrench

Test Video Cable 1 Waterproof Cap

and Gasket 1 set

DC Plug Cable

(DWC-MPB45WiAT

and DWC-MB45WiAT)

Test video

output

Reset button

Zoom lens

button

SD card

input

Quick Start Guide

Pass the wires through and make all the necessary connections. See

STEP 4.

1. NETWORK CONNECTIONS – Using a PoE Switch or PoE Injector,

connect the camera using an Ethernet cable for both data and power.

2. NETWORK CONNECTIONS – Not using PoE Switch or PoE Injector,

connect the camera to the switch using an Ethernet cable for data

transmission and use a power adapter to power the camera.

Default Login Information: admin | admin

When logging into the camera for the ﬁrst time, you will be prompted

to set up a new password. You can set the new password using the

DW® IP Finder™ software or directly from the camera’s browser menu.

Quick Start Guide

STEP 4 – CABLING

Use the diagram below to properly connect power, network, audio, alarm

and sensors to the camera.

NOTE: Maximum SD Card size supported: 64GB.

When inserting the SD card into the card slot, the SD

card’s contacts should be facing upward, as shown in

the diagram.

STEP 5 – MANAGING THE SD CARD

1. To install the camera’s SD Card, locate the SD card slot in the

bottom of the camera by unscrewing the con cap.

2. Insert class 10 SD/SDHC/SDXC card into the SD card slot by

pressing the SD card until clicks.

3. To remove the SD card, press the card inward until it clicks to

release from the card slot than pull out from the slot.

N.C

Activation

N.O In 1

COM

In 1

COM

In 1

COM

In 1

COM

6Alarm In

5Alarm Out

3Audio In

1Power

1Network

4Audio Out

DI : Yellow + Dot

DI COM : Yellow

DO1(N.O.) : Blue + Dot

DO1 COM : Blue

Rev Date: 02/21

Speciﬁcations and pricing are subject to change without notice.

STEP 6 – WEB VIEWER

The GUI display may dier by camera models.

NOTE: Some menu options may not be available based on the

camera model. See the full manual for more information.

NOTE: 32bit version of the VLC player must be installed. If you are

using a 64bit system, uninstall the previous 64bit version

and reinstall using the 32bit version.

Once the camera’s network settings have been setup properly, you can

access the camera’s web viewer using the DW IP Finder.

To open the camera’s web viewer:

1. Find the camera using the DW IP Finder.

2. Double-click on the camera’s view in the results table.

3. Press the ‘View Camera Website’. The camera’s web viewer will

open up in your default web browser.

4. Enter the camera’s username and password you setup in the DW IP

Finder. If you did not setup a new username and password via the

DW IP Finder, you will not be able to view video from the camera.

A message will direct you to setup a new password for the camera

to view video.

5. When accessing the camera for the ﬁrst time, install the VLC player

for web ﬁles to view video from the camera.

STEP 6 – DW® IP FINDER™

Thumbnail view

Firmware version

DHCP status

Camera’s uptime

Open IP conﬁguration

settings

Ping camera

Port information

Gateway address

Netmask address

Camera’s MAC address

Filter results

Scan network

Select network to scan

Show/hide thumbnail view

Refresh thumbnail view

Bulk password assignment

Bulk IP assignment

Firmware upgrade

Camera’s name

Camera’s IP address

Part number

Use the DW IP Finder software to scan the network and detect all MEGApix® cameras, set the camera’s network settings or access the camera’s web client.

Network Setup

1. To install the DW IP Finder, go to

http://www.digital-watchdog.com

2. Enter “DW IP Finder” on the search box at the top of the page.

3. Go to the “Software” tab on the DW IP Finder page to download

the installation ﬁle.

4. Follow the installation to install the DW IP Finder. Open the

DW IP Finder and click ‘Scan Devices’. It will scan the selected

network for all supported devices and list the results in the

table. During the scan, the DW® logo will turn gray.

‘Port forwarding’ has to be set in your

network’s router for external access to the

camera.

Select DHCP to allow the camera to receive its IP address automatically

from the DHCP server.

Select “Static” to manually enter the camera’s IP address, (Sub)Netmask,

Gateway and DNS information.

* The camera’s IP must be set to Static if connecting to

Spectrum® IPVMS

Contact your network administrator for more information.

Default TCP/IP information: DHCP

5. When connecting to the camera for the ﬁrst time, a password

must be set. To set up a password for your new camera:

a. Check the box next to your new camera from the IP Finder’s

search results. You can select multiple cameras.

b. Click “Bulk Password Assign” on the left.

c. In the pop-up window, enter admin/

admin in the current username and

password ﬁelds. Enter a new

username and password to the right.

d. Press “change” to apply all changes.

6. Select a camera from the list by

double-clicking on the camera’s image

or clicking on the ‘Click’ button under

the IP Conf. column. The pop-up

window will show the camera’s current

network settings, allowing admin users

to adjust the settings as needed.

7. To access the camera’s web page, go

to the IP Conﬁg page and click on the

‘View Camera Website’.

8. To save the changes made to the

camera’s setting, input the username

and password of the camera and

click Apply.

NOTE: Chrome browser is recommended for IVA conﬁguration.

Produkt Specifikationer

Mærke:	Digital Watchdog
Kategori:	Overvågningskamera
Model:	MegaPix IVA+ DWC-MPB45WIAT

Har du brug for hjælp?

Hvis du har brug for hjælp til Digital Watchdog MegaPix IVA+ DWC-MPB45WIAT stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Overvågningskamera Digital Watchdog Manualer

Digital Watchdog MegaPix DWC-MB95WI Manual

1 December 2024

Digital Watchdog MEGApix DWC-MV72DI Manual

1 December 2024

Digital Watchdog MEGApix DWC-MPF2WI Manual

1 December 2024

Digital Watchdog MEGApix DWC-MF2WI Manual

1 December 2024

Digital Watchdog Star-Light DWC-D3263TIR Manual

1 December 2024

Digital Watchdog DWC-B6263WTIR 2.1MP Outdoor Universal HD Analog Bullet Camera wit Manual

1 December 2024

Digital Watchdog MEGApix CaaS DWC-MB44WIAWC Manual

30 November 2024

Digital Watchdog MegaPix DWC-MVA2WiAT Manual

30 November 2024

Digital Watchdog MegaPix CaaS DWC-MB44WI650C6 Manual

30 November 2024

Digital Watchdog MegaPix DWC-MV72WI4A Manual

30 November 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

Arecont Vision MicroDome G2 AV2555DN-F-NL Manual

17 Juni 2025

Arecont Vision SurroundVideo G5 Mini AV20CPD-118 Manual

17 Juni 2025

Arecont Vision MicroDome Duo AV10956DN-28 Manual

17 Juni 2025

Arecont Vision SurroundVideo Omni SX AV12275DN-NL Manual

17 Juni 2025

Arecont Vision MicroDome G2 AV3556DNIR-S-NL Manual

17 Juni 2025

Axis Q3548-LVE Manual

17 Juni 2025

Arecont Vision MicroDome Duo AV4656DN-08 Manual

17 Juni 2025

Arecont Vision MicroDome G2 AV5856DNIR-F Manual

17 Juni 2025

Arecont Vision ConteraIP Omni LX AV20476DN-NL Manual

17 Juni 2025

Arecont Vision MicroDome G2 AV5756DNIR-S Manual

17 Juni 2025