Digital Watchdog MegaPix PTZ DWC-MPTZ830XW Manual

Digital Watchdog Overvågningskamera MegaPix PTZ DWC-MPTZ830XW

Læs gratis den danske manual til Digital Watchdog MegaPix PTZ DWC-MPTZ830XW (3 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Digital Watchdog MegaPix PTZ DWC-MPTZ830XW, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

1. The mounting surface must withstand ﬁve times the camera weight.

2. Do not let the cables get caught in improper places or the electric line

cover can be damaged. This may cause a short or ﬁre.

3. For the installation process, remove the protection ﬁlm and the tape

from attached the dome camera.

4. A silicone rubber sealant must be applied to seal the housing to

secure waterprooﬁng.

5. Using the mounting template sheet or the camera itself, mark and drill

the necessary holes in the wall or ceiling.

Tel: +1 (866) 446-3595 / (813) 888-9555

Technical Support Hours:

9:00AM – 8:00PM EST, Monday through Friday

digital-watchdog.com

DWC-MPTZ336XW DWC-MPTZ830XW

Quick Start GuideQuick Start Guide

Default Login Information

Username: admin Password: admin

ACCESSORIES REQUIRED TO INSTALL THE CAMERA (SOLD SEPARATELY)

Wall mount bracket:

DWC-P336WMW

Ceiling mount bracket:

DWC-P336CMW

Parapet mount bracket:

DWC-P336PARAMW

For corner and pole mount bracket:

DWC-P30CNMW (must be purchased with DWC-P336WMW)

STEP 3 – INSTALLING THE CAMERA

Installing the camera using a wall mount

STEP 1 – PREPARING TO MOUNT THE CAMERA

NOTE: Mounting accessories are required and sold separately.

WHAT’S IN THE BOX

QSG 1 Adapter ring 1

PoE injector 1 Waterproof

cap 1 set

Safety wire 1

2P, 5P

screw-type

connectors 1 set

Power cord 1

Installing the camera using a ceiling mount

Attention: This document is intended to serve as a quick reference for the initial

set up. It is recommended that the user read the entire instruction manual for

complete and proper installation and usage.

NOTE: Download all your support materials and tools in one place.

1. Go to: http://www.digital-watchdog.com/resources

2. Search your product by entering the part number in the

‘Search by Product’ search bar. Results for applicable

part numbers will populate automatically based on the

part number you enter.

3. Click . All supported materials, including manuals ‘Search’

and quick start guide (QSGs) will appear in the results.

Plastic anchors (4x)

Tapping screws 8x35 (4x)

Machine screws M3x5 (2x)

Access plate

Safety wire

Set screw (1x)

Adapter PT 1.5 inch (1x)

Mounting bracket (1x sold

separately) PF 1.5 inch

Set screw (1x)

Plastic anchors (3x)

Mounting bracket (1x

sold separately)

Set screws (2x)

Locking nut (1x)

Tapping screws 6x35 (3x)

Socket (1x)

Safety wire (1x)

Machine screw M5x6 (1x)

Pipe (1x)

Set screw (1x)

Set screws (3x)

Pipe socket PF 1.5 incg (1x)

Adapter PT 1.5 inch (1x)

1. Using the mounting template or the mounting accessory itself, mark and drill

the necessary holes in the mounting surface.

2. Pull all cables through the mounting accessory. See STEP 4.

3. Attach the wall mounting bracket to the mounting surface using plastic anchors

and M8x35 screws.

For a ceiling mounting bracket installation, use the plastic anchors to secure it to

the mounting surface.

4. Wind both of the pipe ends thread with Teﬂon tape about 20 times for sealing.

Use a silicone rubber sealant to seal the area where the mounting bracket and

the pipe meet.

5. Place a bead of silicone sealant around the mounting bracket’s mounting ﬂange,

press it to the surface and line up the ﬂange hole with drilled holes.

6. Open the access plate on the mounting accessory and pull out the cables

through the rectangular access hole.

7. Attach the 1.5” adapter to the mounting bracket and ﬁx it using the set screw.

8. Attach the camera’s safety wire to the mounting bracket and organize the

cables.

9. Connect all the cables to the camera. See STEP 4. Close the access plate o the

mounting bracket.

10. Connect the camera to the mounting bracket by turning it clockwise into the

adapter, and ﬁx it using the set screw of the adapter.

Pass the wires through the mount bracket and make all necessary

connections.

1. NETWORK CONNECTIONS – If you are using the PoE injector

included, connect the camera using an Ethernet cable for both data

and power.

2. NETWORK CONNECTIONS – If you are using a non-PoE switch,

connect the camera to the switch using an Ethernet cable for data

transmission and use a power adapter to power the camera.

STEP 2 – POWERING THE CAMERA

Power requirements Power consumption

UPoE injector, 12VDC

(PoE injector included, adapter not

included)

PoE: 28W, 500mA

12VDC: 28W, 2.3A

Ethernet

Cable

Power

Ethernet

Cable

Twist

Start Point

(Long Indicator)

Set Point

(Long Indicator)

Seal using silicone

rubber around the circle

NOTE: Please see the full product manual for web viewer setup,

functions and camera settings options.

1. Open the micro-SD card cover under the camera’s lens.

2. Insert or remove the micro-SD card as needed.

3. Tightly close the micro-SD card cover to ensure it is waterproof.

Users can insert and remove a micro-SD card as shown in the

following picture.

STEP 3 – MANAGING THE SD CARD STEP 6 – NETWORK ACCESS (WEB)

STEP 7 – LIVE VIEW

Rev Date: 05/20

Speciﬁcations and pricing are subject to change without notice.

Quick Start Guide

1. Enter the camera’s IP address in a web browser (IE is

recommended). The

2. In the welcome screen, select whether to view a live image from the

camera, search recorded data on the SD card or enter the camera’s

settings.

3. If you are entering the camera’s settings, enter the user name and

password (default admin/admin).

5 6 7 8 9 10 11 12 13

2 3 4

1. Select Stream 1 (H.264), Stream 2 (MJPEG), Stream 3 (H.264)

2. Select resolution up to 1920x1080

3. Select network protocol between HTTP, TCP, and UDP

4. Call preset up to 256

5. Stop and start for live stream

6. Stream pause

7. Snapshot

8. Zoom

9. Fullscreen

10. Manual trigger

11. Pop-up PTZ control panel

12. Speaker volume

13. Microphone control

1110

Resetting the camera: To reset the camera, use the tip of a paper

clip or a pencil and press the reset button located under the

camera’s lens module. See the diagram above for it’s location.

Pressing the button for ﬁve (5) seconds will initiate a camera-wide

reset of all the settings, including network settings.

STEP 5 – DW® IP FINDER™

Thumbnail view

Firmware version

Camera’s uptime

Open Device

conﬁguration

settings

Filter device type to scan

Scan devices

Select network to scan

Show/hide thumbnail view

Refresh thumbnail view

Bulk IP assignment

Firmware upgrade

Device’s

information

Use the DW® IP Finder™ software to scan the network and detect all MEGApix® cameras, set the camera’s network settings or access the camera’s web client.

Network setup

1. To install the DW® IP Finder™, go to

http://www.digital-watchdog.com

2. Enter “DW IP Finder” on the search box at the top of the page

and press Enter.

3. Click on the DW® IP Finder™ from the search result and go to the

Software tab. Click on the download icon to download the DW®

IP Finder™ installation ﬁle.

4. Run the installation ﬁle and follow the wizard to install the DW®

IP Finder™. Open the DW® IP Finder™ and click ‘Scan Devices’. It

will scan the selected network for all supported devices and list

the results in the table. During the scan, the DW® logo will

turn gray.

Default ID / PW: admin / admin

‘Port forwarding’ has to be set in your

network’s router for external access

to the camera.

*NOTE: For security purposes, it is highly

recommended to change your

password after initial setup.

Default TCP/IP information: DHCP

Select DHCP if the internet service is dynamic IP. This will allow the

camera to receive its IP address from the DHCP server.

Select “Static” to manually enter the camera’s IP address, (Sub)

Netmask, Gateway and DNS information.

The camera’s IP must be set to Static if connecting to DW Spectrum®

IPVMS. Contact your network administrator for more information.

5. Select a camera from the list by double-clicking on the

camera’s image or clicking on the ‘Click’ button under the

IP Conf. column. The pop-up window will show the camera’s

current network settings, allowing admin users to adjust the

settings as needed.

6. To access the camera’s web page, click on ‘View

Camera Website’.

7. To save the changes made to the

camera’s setting, input the username

and password of the camera and click

Apply. Click “Scan Devices” from the

main screen again to display the

updated information.

Reset button

Micro-SD card slot

No Connector Wire Color Description

1 Power jack Black Camera power (12VDC)

2 RJ-45 Black Ethernet

3 RCA jack Black Audio input

4 RCA jack Gray Audio output

5 5-pin cable

Yellow Alarm input 1

White Alarm input 2

Violet Alarm input 3

Brown Alarm input 4

Gray GND

6 2-pin cable Red Alarm output

Black GND

STEP 4 – CABLING

Use the diagram below to connect external devices such as audio

and alarm inputs and outputs to the camera.

Produkt Specifikationer

Mærke:	Digital Watchdog
Kategori:	Overvågningskamera
Model:	MegaPix PTZ DWC-MPTZ830XW

Har du brug for hjælp?

Hvis du har brug for hjælp til Digital Watchdog MegaPix PTZ DWC-MPTZ830XW stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Overvågningskamera Digital Watchdog Manualer

Digital Watchdog MegaPix DWC-MB95WI Manual

1 December 2024

Digital Watchdog MEGApix DWC-MV72DI Manual

1 December 2024

Digital Watchdog MEGApix DWC-MPF2WI Manual

1 December 2024

Digital Watchdog MEGApix DWC-MF2WI Manual

1 December 2024

Digital Watchdog Star-Light DWC-D3263TIR Manual

1 December 2024

Digital Watchdog DWC-B6263WTIR 2.1MP Outdoor Universal HD Analog Bullet Camera wit Manual

1 December 2024

Digital Watchdog MEGApix CaaS DWC-MB44WIAWC Manual

30 November 2024

Digital Watchdog MegaPix DWC-MVA2WiAT Manual

30 November 2024

Digital Watchdog MegaPix CaaS DWC-MB44WI650C6 Manual

30 November 2024

Digital Watchdog MegaPix DWC-MV72WI4A Manual

30 November 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

1 August 2025

31 Juli 2025

31 Juli 2025

31 Juli 2025

FLIR ioi HD CB-5222 Manual

30 Juli 2025

Eufy Cam S3 Pro Manual

30 Juli 2025

Telycam Vision+ 4KN 30X Manual

30 Juli 2025

Marshall Electronics CV630-BI Manual

30 Juli 2025

Telycam Vision+ SE Manual

30 Juli 2025

FLIR Ariel CC-3405 Manual

29 Juli 2025