Dimplex 403BT Manual

Dimplex Ikke kategoriseret 403BT

Læs gratis den danske manual til Dimplex 403BT (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 38 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 19.5 anmeldelser. Har du et spørgsmål om Dimplex 403BT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

attention has to be given where children and

vulnerable people are present.

WARNING: Do not use the heater in small rooms

when they are occupied by persons who are not

capable of leaving the room on their own, unless

constant supervision is provided.

WARNING: To reduce the risk of re, keep

textiles, curtains or any other ammable material

a minimum distance of 1m from the air outlet.

Do not use the heater if it has been dropped.

Do not use the heater if there are any visible

signs of damage.

If the mains lead is damaged, it must be replaced

by the manufacturer or its service agent or a

similarly qualied person in order to avoid a

hazard.

The heater should only be used on a horizontal

and stable surface with the feet securely tted

Electrical connection

WARNING – THIS APPLIANCE MUST BE EARTHED

The use of an extension lead or multi-plug adaptor is not advised when

connecting this product to the mains. Connection through these devices

could lead to a risk of overloading, overheating and even re at the extension

lead or adaptor due to inadequate connection quality.

This heater must be used on an ~ supply only and the voltage marked on

the heater must correspond to the supply voltage. This heater is tted with

a rewireable plug incorporating a 13 amp fuse. In the event of replacing

the fuse in the plug supplied, a 13 amp fuse approved by ASTA to BS 1362

must be used. If any other type of plug is used, a 15 amp fuse must be

tted in the plug, the adaptor, or at the distribution board.

IMPORTANT : If the plug is not suitable for your socket, the 13 amp plug

should be removed. Before wiring the appropriate plug, please note that

the wires in this mains lead are coloured in accordance with the following

code : GREEN AND YELLOW: EARTH

BLUE : NEUTRAL

BROWN : LIVE

Connect the wire to the terminal marked ‘ ’ or GREEN AND YELLOW E

by the earth symbol , or coloured or .GREEN GREEN AND YELLOW

Connect the wire to the terminal marked ‘ ’ or coloured .BROWN L RED

Connect the wire to the terminal marked ‘ ’ or coloured BLUE N BLACK.

Important Safety Advice

WARNING: This appliance must not be used in

a bathroom.

WARNING: Do not use this heater in the

immediate surroundings of a bath, a shower or

a swimming pool.

WARNING: This heater must not be located

immediately below a xed socket outlet.

The heater carries a warning symbol to

alert the user to the risk of re that exists

if the heater is accidentally covered.

WARNING: In order to avoid a hazard due to

inadvertent resetting of the thermal cut-out,

this appliance must not be supplied through an

external switching device, such as a timer, or

connected to a circuit that is regularly switched

on and off by the utility.

This appliance can be used by children aged

from 8 years and above and persons with

reduced physical, sensory or mental capabilities

or lack of experience or knowledge if they have

been given supervision or instruction concerning

the use of the appliance in a safe way and

understand the hazards involved. Children shall

not play with the appliance. Cleaning and user

maintenance shall not be made by children

without supervision.

Children of less than 3 years should be kept

away unless continuously supervised. Children

aged from 3 years and less than 8 years shall

only switch on/off the appliance provided that

it has been placed or installed in its intended

normal operating position and they have been

given supervision or instruction concerning

the use of the appliance in a safe way and

understand the hazards involved. Children aged

from 3 years and less than 8 years shall not plug

in, regulate and clean the appliance or perform

user maintenance.

CAUTION: Some parts of this product can

become very hot and cause burns. Particular

Dimensions

(Millimetres)

Installation and Operating Instructions

Dimplex Convector Heater

Models : 403BTB & 403BT

INDCUK40BT Issue 4

IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

As with all portable heating appliances - This product is only suitable for well insulated spaces or occasional use

Fig. 1

Using the heater

WARNING: DO NOT USE THE HEATER UNTIL THE FEET ARE

FITTED CORRECTLY.

The product can be used as an installed or portable unit. Once the desired

application has been decided upon and the requirements below have been

met the product is ready to be used. Simply plug in and switch on at the

wall socket.

Please note – the element has been coated with a protective lm which

will burn off during the rst few minutes of use and may cause a small

amount of fuming. This is quite normal – the fumes are non-toxic and will

quickly disappear.

We recommend that you open a window to ventilate the room when using

the heater for the rst time.

Positioning the heater

Always ensure that the heater is stood on a rm, level base near to,

but not directly beneath, a suitable mains supply socket.

Ensure that curtains and furniture are not positioned close to the

chosen position, as this would create a potential re hazard.

Product Assembly

WARNING: THE HEATER SHOULD NEVER BE USED WITHOUT THE

FEET SECURELY FITTED.

Lay the heater on its back so the underneath of the product is accessible.

Locate and remove the foot xing screw - see Fig. 2(a). Clip the foot in

place and secure using the foot xing screw - see Fig. 2(b).

Controls

LCD Display

Heat Neon

Mains Neon

Bluetooth Neon

Standby

Down

Prog mmera

Mode/Pair

Desired

Temper eatur

Selected

Mode

Selected Heat

Seng

En rte

NOTE: When using the appliance or setting appliance controls always

ensure that the heater is stood on a rm level base. Do not tilt the

appliance at any time.

Operational modes

The electronic control has four control modes: AUTO MANUAL, , BOOST

and STANDBY mode.

Auto Mode

Standby ModeBoost Mode

Manual Mode

Fig. 2

Fig. 3

Fig. 4

In both and mode there are three heat settings options:MANUAL AUTO

‘Intelligent’ Eco Mode - This is the initial default setting, the convector will

automatically start up in this setting once power is applied. The convector

will automatically regulate the room temperature accordingly. In this mode

the convector operates at full power, however the output of the convector is

automatically reduced and regulated as the room temperature approaches

the desired level. This mode optimises energy use by calculating the most

efcient and effective way to achieve the desired temperature setting. The

desired room temperature can be adjusted at any time during operation by

pressing the appropriate key.

Low Heat - In this option, the appliance will operate at a low heat setting,

the appliance will automatically cycle at this setting to maintain the room

temperature setting.

High Heat - In this option, the appliance will operate at a high heat setting,

the appliance will automatically cycle at this setting to maintain the room

temperature setting.

Press the Mode key,‘ ’, to toggle through the modes and the key ENTER

to conrm the mode selection. Note: when selecting the mode if the ENTER

key is not pressed, after 5 seconds the heater will activate the mode shown

on the LCD display.

Initial Operation

When the heater is initially connected to the mains the heater will power

up in and MANUAL Mains

mode with a set temperature of 30˚C. The

Heat Fig.6indication neon will be lit and the LCD display will be as per .

For subsequent operations the unit will power up in its previous state, i.e.

if it was in the boost mode when the unit was plugged out when power is

reinstated it will resume in boost mode.

Setting the Time

To set the time press and hold ‘ ’ for two seconds, the time digits will begin

ashing (Fig. 7). Press the ‘ ’ or ‘ ’ buttons to set the time and press

ENTER to conrm. The heater will revert to the previous operational mode.

Flashing

Standby Mode

With the heater if the button is pressed, the heater will go into standby ON,

mode; the heater switches off, the LCD will display the current set time, only

the mains neon remains illuminated. On pressing the button again the

heater will come on in Manual mode and with a set point setting of 25 ˚C.

Fig. 5

Fig. 6

Fig. 7

Produkt Specifikationer

Mærke:	Dimplex
Kategori:	Ikke kategoriseret
Model:	403BT

Har du brug for hjælp?

Hvis du har brug for hjælp til Dimplex 403BT stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Dimplex Manualer

Dimplex QRAD200E Manual

12 Januar 2025

Dimplex Optiflame 3D GLN20BR3D Manual

30 December 2025

Dimplex CFH90 Manual

5 Oktober 2024

Dimplex OCR20Tie Manual

1 Oktober 2024

Dimplex OPH13 Manual

29 September 2024

Dimplex GLN20BR Manual

18 September 2024

Dimplex SRX120EM Manual

17 September 2024

Dimplex CAB10ER Manual

12 September 2024

Dimplex RFM Manual

6 September 2024

Dimplex CAS400NH Manual

31 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Planet Audio P100CPA Manual

15 Juni 2025

Sabrent BK-MAC2 Manual

15 Juni 2025

Planet Audio P9950CPA Manual

15 Juni 2025

Filmcity FC-CTH-01 Manual

15 Juni 2025

Cleveland 22CGT6 Manual

15 Juni 2025

Auray SVRK-4U-S Manual

15 Juni 2025

Bobrick B-2860 Manual

15 Juni 2025

Sony ODBK-103 Manual

15 Juni 2025

Planet Audio P70CPA Manual

15 Juni 2025

Gourmia GAF657 Manual

15 Juni 2025