Dimplex BR350C Manual

Dimplex Ikke kategoriseret BR350C

Læs gratis den danske manual til Dimplex BR350C (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 47 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 24 anmeldelser. Har du et spørgsmål om Dimplex BR350C, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

100 min.

150 min.

shelf

BR150 / BR200 / BR350 BR250 BR400 BR500

Dimensions

(millimetres)

Installation and Operating Instructions

Venita Towel Rails

Models : BR150, BR200, BR250, BR350, BR400 & BR500

08/17311/1 Issue 1

Important Safety advice

WARNING - THE SURFACE OF THIS RADIATOR CAN BE

HOT.

In order to be effective the towel rail will get hot,

however momentary contact with any part of it should not

cause injury.

CAUTION - This appliance is not intended for use by

chidren or other persons without assistance or

supervision if their physical, sensory or mental

capabilities prevent them from using it safely.

Children should be supervised to ensure that they do

not play with the appliance.

Precautions should be taken to ensure that prolonged

contact with the towel rail cannot occur. Particular care

should be taken in confined areas where accidental

prolonged contact with the rail could be more likely to

occur.

IMPORTANT - If the towel rail is to be installed in a place

used by the public, a warning notice should be placed

adjacent to the rail advising that the surface can be hot.

General

The Venita towel rail is designed to provide an all year round

service for airing towels and articles of clothing. It will also

provide heat for bathrooms and other small rooms. The

towel rail is permanently filled with a special water based

liquid for years of trouble free service. No routine

maintenance is necessary apart from occasional

cleaning.

The towel rail has a sealed electrical element controlled by a

pre-set thermostat which will switch off the rail should it

overheat for any reason. It is splashproof to IPX4 standard.

The Venita towel rail also has the facility for connection to a

water radiator system and can be operated as part of a

central heating system. (See section ‘Use on a water

radiator system’).

Electrical

The electrical installation of this towel rail must be carried

out by a competent electrician in accordance with the current

I.E.E Regulations for Electrical Equipment. The towel rail is

suitable for use on an A.C.~ electrical supply. Before

installation check that the supply voltage corresponds with

that marked on the rail.

WARNING - THIS APPLIANCE MUST BE EARTHED.

IMPORTANT - The wires in the mains lead are coloured in

accordance with the following code:

GREEN and YELLOW - EARTH

BLUE - NEUTRAL

BROWN - LIVE

As the colours of the wires in the mains lead of this

appliance may not correspond with the coloured markings

identifying the terminals in your plug, proceed as follows:

The wire which is coloured GREEN and YELLOW must be

connected to the terminal in the plug which is marked with

the letter E or by the earth symbol or coloured green or

green and yellow.

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured black.

The wire which is coloured BROWN must be connected to

the terminal which is marked with the letter L or coloured red.

This appliance must only be used on A.C. mains supply of

230/240 Volts~.

Fig. 1

Watts

150

200

250

350

400

500

Weight kg

6.5

Model

BR150

BR200

BR250

BR350

BR400

BR500

Rails

665

1003

1345

610

390

602

443

602

443

155

F - Bleed valve

G - Drain plug

IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

(e)

screws

No.10 x 40

mounting

straps

cross

bar

wall mtg.

brackets

Note: Mounting

strap must be

positioned up

tight to the

cross bar

Detail view of mounting

strap/cross bar

mounting

strap

upright

bar

(c)

wall mounting

bracket

(a)

mounting

strap

phillips head

screwdriver

flat head

screwdriver

(b)

screw M4x10

(d)

locater pin

rotated quarter

turn to lock

Bathroom Installations

If fitted in a room containing a bath or shower, to comply with

the current I.E.E. Regulations, a cable outlet will be

necessary with the supply to the heater controlled by a

double-pole pull-cord switch having a contact separation of

3mm in each pole. The body of the switch should be

situated as to be normally inaccessible to a person using a

bath or shower. Should Equipotential Earth Bonding be

required the earthing conductor in the supply cord is deemed

to provide the supplementary bonding connection (see

Regulation 547-03-0@,’16’h Edition I.E.E. Wiring

Regulations.

Installation

IMPORTANT - Protect the electrical connection whilst

handling the towel rail.

The towel rail must be permanently fixed to the wall using the

wall brackets supplied. The rail must be mounted vertically

as shown observing the minimum clearances stated.

WARNING - The towel rail is heavy. Do not remove without

seeking specialist advice.

Wall mounting

The Wall mounting accessory pack contains:

(a) 4 mounting straps

(b) 4 screws (M4 x 10)

(d) 4 locator pins

(e) 4 wall mounting screws (No.10 x 40) and wall plugs

Procedure for fixing Wall Brackets

Step 1

Using Dim. X (fixed) and Dim. Y (variable) as a guide, mark

the hole positions for the four fixing brackets and drill and

plug the wall to suit.

Note: Allow enough room above and below for the clearance

stated. Screw the four fixing brackets securely to the wall -

see Fig. 3.

Step 2

Place carefully around the upright bars the 4 mounting

straps at the position shown - see Fig. 3. (Note the straps

must be positioned up tight to the cross bar as indicated)

Securely fix them by screwing in place fully the M4 x 10mm

screw. Ensure the brackets are fitted with the rear of the

straps facing directly backwards.

Step 3

Place the towel rail straps into the wall mounted brackets,

secure them with the locater pins by inserting it and giving it

a quarter turn - see Fig 3. Check the four brackets and towel

rail are fitting horizontal. If not go back to step 2. The straps

can be repositioned to ensure that the towel rail is horizontal

when fitted to your wall. If the towel rail cross rails are not

level, loosen both straps on either left or right hand upright

bar. Lower the two straps and raise up the towel rail until it

is horizontal, then secure as indicated in step 2 and 3.

Fig. 3

Wall bracket Fixing Dimensions

Model(s) Dim. X Dim. Y

BR150 385 318

BR200 603 318

BR350 603 634

BR250 447 318

BR400 447 638

BR500 447 958

Fig. 2

Produkt Specifikationer

Mærke:	Dimplex
Kategori:	Ikke kategoriseret
Model:	BR350C

Har du brug for hjælp?

Hvis du har brug for hjælp til Dimplex BR350C stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Dimplex Manualer

Dimplex QRAD200E Manual

12 Januar 2025

Dimplex Optiflame 3D GLN20BR3D Manual

30 December 2025

Dimplex CFH90 Manual

5 Oktober 2024

Dimplex OCR20Tie Manual

1 Oktober 2024

Dimplex OPH13 Manual

29 September 2024

Dimplex GLN20BR Manual

18 September 2024

Dimplex SRX120EM Manual

17 September 2024

Dimplex CAB10ER Manual

12 September 2024

Dimplex RFM Manual

6 September 2024

Dimplex CAS400NH Manual

31 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Aiphone GT-4ZP Manual

15 Juni 2025

Moulinex Secanto DJAB41 Manual

15 Juni 2025

Blodgett Invoq 201E Manual

15 Juni 2025

Vocopro FIELD-QUAD-H Manual

15 Juni 2025

ORNO OR-DB-MK-175P Manual

15 Juni 2025

Milwaukee M12 HSFSM Manual

15 Juni 2025

Berkel Suprema Salumeria PES370 Manual

15 Juni 2025

Bugaboo Butterfly 2 car seat adapters Manual

15 Juni 2025

ORNO OR-CR-278 Manual

15 Juni 2025

Wahoo BLUE SC Manual

15 Juni 2025