Dimplex RX9912 Manual

Dimplex Ikke kategoriseret RX9912

Læs gratis den danske manual til Dimplex RX9912 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Dimplex RX9912, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/3
Contact Details
Pleasenotethat some contact ofthe details on 
thisPDFdocumentmaynotbe current.
Pleaseuse  the following detailsifyouneedto
contactus:
Telephone:0844 879 3588
Email:customer.services@gdcgroup.co.uk
The widecustomer alsosupportsection websiteofour  features a
rangeof ofinformationwhichmaybe use availabletoyouandis 
24 ahours day.Itincludes:
• Operating  and installation instructions
• Easy   ‘How to use’ guides for storage heaters
• Service  and repairs
• Wheretobuyourproducts
• Literature downloads
• Heating  requirement calculator
 ‐Visit www.dimplex.co.uk/support
A division of GDC Group Ltd
Millbrook House Grange Drive Hedge End Southampton SO30 2DF
www.dimplex.co.uk
Re
g
istered No: 1313016 En
g
land
VAT GB 287 1315 50004
EEE Producer Registration Number –
WEE/GE0057TS
Paper from sustainable sources
Installation and
Operating Instructions
Mains Signalling Transmitter - Model No. RX9912
General Description
Installation
Single Zone Programming:
Multi Zone Programming:
Activating the Receivers:
The RX9912 can only be used in RPX, EVX and EVS heaters.
Each programmer may be used to provide single or multi zone programming for up to 20 slave
heaters, each fitted with a mains signalling receiver (Dimplex Part No. RX9913).
Two heating positions are offered: comfort and economy setback, with room temperatures set
using the controls on the heater.A choice of heating programmes are available for each day of
the week. There are 7 pre-set programmes, from P1 to P7 or a customised programme P=. In the
event of a power supply interruption or the cassette being removed from the heater, the memory
will retain current time and customised programme for 1 hour.The seven pre-set programmes will
remain stored indefinitely.
The RX9912 is rated at 230V.
1. Using a narrow bladed screwdriver, carefully release the cover from the slot adjacent to
the controls on the heater
2. Insert the programmer fully so that it clicks into position
3. Turn the control knob on the heater(s) to the PROG position
The heater containing the RX9912 is the transmitter or master heater, which
sends a message to the slave heaters, each containing the RX9913 receivers.
The transmitter heater determines the programme and heating levels for all the
heaters (Comfort, Setback and Frost Protection), but the actual comfort and
setback temperatures should still be set on each individual heater (see heater
instructions). The transmitter heater will switch between comfort and setback
according to the programme. On every slave heater, turn the control knob to
PROG.
In this mode all slave heaters will operate on the same master programme.
1. Insert the RX9912 into the master heater.
2. Press mode for 5 seconds. The house factory set code
appears.
3. Press mode to confirm the house code - the number 1 will
appear.
4. Press mode to confirm Zone 1.
5. During transmission the transmitter will flash EMET and the
number 1 alternatively.Activate all heaters containing receiver
following the instructions below (§ Activating the receivers).
It is possible to create up to 3 zones of heating using the RX9912 (One RX9912 per zone is
needed).
1. Insert the RX9912 into the master heater.
2. Follow the instructions for creating a single zone, but at step 4 use the
++++ key to select
option of zone 2 or 3.
3. Press mode to confirm OK when required zone is displayed.
4. The screen will now flash EMET and the appropriate zone number.
5. Activate all slave heaters containing receivers which you wish to be dedicated to either
zone 2 or 3 by following the instructions below.
1. Confirm the slave heater selector switch is positioned on PROG.
2. Press the small button (A) for 10 seconds (using a small screwdriver
blade or pen tip) until the neon indicator flashes.
3. Release and press again, light indicator will be ON.
4. Repeat process for each slave heater.
5. Return to master heater programmer and press OK
Display
1
2
3
4
5
6
7
03 : 58
+ -/Hgel OK MODE
Comfort Hours
Setback Hours
Override - Frost Protection
4. Choice of programme
for each day
1 segment per hour
1. Time
2. Day
3. Indicator
flashes
Transmitter (RX9912)
Receiver (RX9913)
Receiver (RX9913)
Power
Supply
Earth
Live
Neutral
A
EMET
+ -/Hgel OK MODE
T9909/010/A
421AA0793.A NR/BLA 49/99
- 1/2 -

Produkt Specifikationer

Mærke: Dimplex
Kategori: Ikke kategoriseret
Model: RX9912

Har du brug for hjælp?

Hvis du har brug for hjælp til Dimplex RX9912 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Dimplex Manualer

Dimplex

Dimplex QRAD200E Manual

12 Januar 2025
Dimplex

Dimplex Optiflame 3D GLN20BR3D Manual

30 December 2025
Dimplex

Dimplex CFH90 Manual

5 Oktober 2024
Dimplex

Dimplex OCR20Tie Manual

1 Oktober 2024
Dimplex

Dimplex OPH13 Manual

29 September 2024
Dimplex

Dimplex GLN20BR Manual

18 September 2024
Dimplex

Dimplex SRX120EM Manual

17 September 2024
Dimplex

Dimplex CAB10ER Manual

12 September 2024
Dimplex

Dimplex RFM Manual

6 September 2024
Dimplex

Dimplex CAS400NH Manual

31 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Simrad

Simrad Active Imaging HD (Thru-Hull) Manual

14 Juni 2025
Garritan

Garritan Harps Manual

14 Juni 2025
Marshall

Marshall CV-H20-HF Manual

14 Juni 2025
Aiphone

Aiphone IXW-MAA Manual

14 Juni 2025
Rival

Rival HM-743 Manual

14 Juni 2025
Lutec

Lutec Avony Manual

14 Juni 2025
Giordani

Giordani G-SAFE & PLAY Manual

14 Juni 2025
Gourmia

Gourmia GAF799 Manual

14 Juni 2025
Arendo

Arendo 307503 Manual

14 Juni 2025
Hughes & Kettner

Hughes & Kettner Tube 100 Manual

14 Juni 2025