Escort Passport SR1 Manual

Escort Ikke kategoriseret Passport SR1

Læs gratis den danske manual til Escort Passport SR1 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 6 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 3.5 anmeldelser. Har du et spørgsmål om Escort Passport SR1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Important Note

This product must be installed by a professional.

Please read the installation warnings inside.

Please read this entire installation sheet before

beginning your installation.

To ensure the high-performance radar and laser

detection that Escort detectors are known for, the

mounting location of the front receiver is critical.

Although Radar signals will go through some types

of plastic, Laser signals will not.

It is very important

to mount the Front Receiver in a level position that

gives it a clear “view” of the road ahead.

The metal mounting brackets provided have several

different mounting holes, and can be used for most

vehicles. However, additional mounting hardware

may be required for some installations.

Installation Instructions for Passport SR1

For Professional Installation Only

Installation

1Slide 3” section of heat-shrink tubing over

connector, then connect receiver cable to

cable from Front Receiver. (Fit connectors

together, then twist large ring until it clicks.)

Do not shrink the heat-shrink tubing until

the detector is installed and operational.

2Route cable to firewall, secure with zip-ties.

3Route cable into interior. If there is not a

suitable opening, drill a 13/32” or 7/16”

diameter hole (slightly larger than 3/8”).

4Route wire inside interior and plug into

jack labeled “Receiver” on EZ-Interface.

5Pull grommet (provided on cable) into

position from vehicle interior to seal hole.

Use silicone sealant (not included) if

necessary for complete sealing.

Think first:

•Connector attaching to Front Receiver

cable must be positioned in a dry location

under hood, away from water spray.

•Only drill hole after thoroughly investigating

location and ensuring no other wires, hoses,

or other components will be damaged.

•Keep cable and connector away from

moving parts and hot surfaces (radiator,

heater hoses, exhaust components).

•Shielded cable– coil excess, do not splice.

Installation

1Determine best location for Receiver. The

best location is usually under the bumper

or just inside the grill. The unit must be

mounted with the arrows pointing forward.

(The radar antenna and laser sensors

“look” out the front of this unit, so

it must

have a clear “view” of the road ahead.)

2Mark location, drill pilot holes in vehicle if

necessary.

3Mount large metal brackets to vehicle

with 4 sheet metal screws and lockwashers.

4Mount to large brackets withReceiver

four 8-32 machine screws and lockwashers.

5Route wire up to a dry location under hood

for the connector, secure with zip-ties.

Think first:

•Do not drill holes in . Mount onlyReceiver

to the preattached side and rear brackets.

•Only drill holes in vehicle after thoroughly

investigating location and ensuring no

other wires, hoses, or other components

will be damaged.

•Keep cable and connector away from

moving parts and hot surfaces (radiator,

heater hoses, exhaust components).

•Shielded cable– do not splice.

Front Radar and Laser Receiver

mounts under bumper or in grille

Receiver Cable connects

Front Receiver to EZ-Interface

Hold here

Slide 3” section of heat-shrink tubing over this

connector, then connect receiver cable to cable

from Front Receiver. (

Carefully fit connectors

together, then twist large ring until it clicks.)this

After installation is complete and unit is opera-

tional, slide the heat-shrink tubing over the

connection, then shrink tubing for air-tight seal.

IMPORTANT

INSTALLATION

WARNINGS

Your new Passport SR1 must be

installed by a professional installer.

Installation of this product requires

experience and expertise in automo-

tive electronics. Car Audio specialists

and many car dealers can install Pass-

port for you.

Attempting to install this product

without expertise in automotive elec-

tronic installations can cause personal

injury during the installation, or can

damage your Passport or your ve-

hicle.

If your vehicle is damaged during

installation, its safety systems may

be compromised, which could cause

personal injury or property damage.

Improper installation may void

Passport’s warranty.

Installation

Read this first!

Please read both sides of

these instructions before

starting your installation.

For the easiest trouble-

free installation, install the

EZ-Interface first, and wire it

to a 12 volt switched circuit.

Then before installing the

other components, plug all

three into the EZ-Interface

and power up con-unit to

firm proper operation.

See the other side of this

instruction sheet for addi-

tional mounting information.

Produkt Specifikationer

Mærke:	Escort
Kategori:	Ikke kategoriseret
Model:	Passport SR1

Har du brug for hjælp?

Hvis du har brug for hjælp til Escort Passport SR1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Escort Manualer

Escort SmartCord Live Manual

16 Juli 2025

Escort Passport GT2 Manual

16 Juli 2025

Escort Shifter ZR3 Manual

15 Juli 2025

Escort Passport GT1 Manual

15 Juli 2025

Escort MAX Ci Platform Manual

15 Juli 2025

Escort Road Tech 75 Manual

15 Juli 2025

Escort MediaFlair Manual

15 Juli 2025

Escort MAX Ci 360 Manual

15 Juli 2025

Escort SmartSite Manual

15 Juli 2025

Escort ZR6 Manual

15 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Roccat Recon Cloud Manual

15 September 2025

AREXX PRO-77IR Manual

15 September 2025

Biltema 29-903 Manual

15 September 2025

Invacare Perfecto IRC5PAW Manual

15 September 2025

Brandson 306618 Manual

15 September 2025

Daewoo AVS1412 Manual

14 September 2025

Neutrik NO4SBB2D-A Manual

14 September 2025

Invacare Perfecto IRC5PO2AW Manual

14 September 2025

Neutrik NO12SABB3Q-A Manual

14 September 2025

JILONG JL097205NPF Manual

14 September 2025