Etna 4421 Manual

Etna Emhætte 4421

Læs gratis den danske manual til Etna 4421 (17 sider) i kategorien Emhætte. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Etna 4421, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/17

- 3 -

587 490102

824 : 1279

Fig.1

Fig.2

G B C D E A

Fig.5Fig.5

A B CD E F

Fig.3

352

203

460

235

253

493

Fig.4

- 4 -

GENERAL

Carefully read the following important information regarding

installation safety and maintenance. Keep this information

booklet accessible for further consultations.

The appliance has been designed as a exhausting version (external

exhaust) or as a filter version (internal air recycle) cooker hood.

SAFETY PRECAUTION

• Take care when the cooker hood is operating simultaneously

with an open fireplace or burner that depend on the air in the

environment and are supplied by other than electrical energy, as

the cooker hood removes the air from the environment which a

burner or fireplace need for combustion.

The negative pressure in the environment must not exceed 4 Pa (4

x 10 –5 bar).

Provide adequate ventilation in the environment for a safe operation

of the cooker hood.

Follow the local laws applicable for external air evacuation.

•WARNING!!

In certain circumstances electrical appliances may be a danger

hazard.

A) Do not check the status of the filters while the cooker

hood is operating

B) Do not touch the light bulbs after appliance use

C) Flambè cooking is prohibited underneath the cooker hood

D) Avoid free flame, as it is damaging for the filters and a

fire hazard

E) Constantly check food frying to avoid that the overheated

oil may become a fire hazard

F) Disconnect the electrical plug prior to any maintenance.

INSTALLATION INSTRUCTIONS

The appliance has been manufactured as a class II, therefore no

earth cable is necessary.

The connection to the mains is carried out as follows:

BROWN = L line

BLUE = N neutral

If not provided, connect a plug for the electrical load indicated on

the description label. Where a plug is provided, the cooker hood

must be installed in order that the plug is easily accessible.

An omnipolar switch with a minimum aperture of 3mm between

contacts, in line with the electrical load and local standards, must

be placed between the appliance and the network in the case of

direct connection to the electrical network.

• The appliance must be installed at a minimum height of 650 mm

from an cooker stove.

If a connection tube composed of two parts is used, the upper part

must be placed outside the lower part.

Do not connect the cooker hood exhaust to the same conductor

used to circulate hot air or for evacuating fumes from other

appliances generated by other than an electrical source.

• Mounting the cooker hood to the wall

Drill holes A-B-C-D according to indications quoted in (fig. 3).

Use screws and screw anchors suitable for wall (e.g. reinforced

cement, plasterboard) for the mounting of the cooker hood.

Where screws and screw anchors are supplied ensure that they

are suitable for the type of wall where the cooker hood is to be

mounted.

Lock in the flange connector Y to the cooker hood (fig. 2).

Affix the bracket Z to the wall via the drill holes A (fig. 4).

Hang the cooker hood on the wall using the drill holes C (fig. 3).

Fasten the cooker hood using the fastening drill holes D (fig. 3).

• Exhausting Version

Connect the flange Y to the discharge opening with a connecting

tube (do not carry out for filter version).

Thread the upper connector E to the inside of the lower connector

F; hang the two connectors inserting them vertically on the cooker

hood locking the lower connector F to the wall using the drill holes

B (fig. 3), unthread the upper connector E towards the top, locking

it in with the appropriate screws in the drill holes G of the bracket

Z (fig. 2) previously affixed to the wall via the drill holes A (fig. 3).

In order to transform your cooker hood from exhausting version to

filter version, ask your local retailer for active carbon filters and

then carry out instructions for mounting filter version cooker hood.

•Filter Version

Install the cooker hood and the two connectors as described in the

paragraph mounting the exhausting version cooker hood.

To mount the filter connector refer to instructions included in the

kit.

If the kit is not supplied, then order the kit as an accessory from

your local dealer.

The filters must be fitted to the fan unit placed inside the cooker

hood. The air is replaced in the environment via the eyelets

impressed on the connector E.

USE AND MAINTENANCE

• It is recommended to operate the appliance prior to cooking.

It is recommended to leave the appliance in operation for 15 minutes

after cooking is terminated in order to completely eliminate cooking

vapours and odours.

The proper function of the cooker hood is conditioned by the

regularity of the maintenance operations, in particular, the active

carbon filter.

• The anti-grease filters capture the grease particles suspended

in the air, and are therefore subject to clogging according to the

frequency of the use of the appliance.

In order to prevent fire hazard, it is recommendable to clean the

filter at a maximum of 2 months by carrying out the following

instructions:

- Remove the filters from the cooker hood and wash them in a

solution of water and neutral liquid detergent, leaving to soak.

- Rinse thoroughly with warm water and leave to dry.

- The filters may also be washed in the dishwasher.

The aluminium panels may alter in colour after several washes.

This is not cause for customer complaint nor replacement of panels.

• The active carbon filters purify the air that is replaced in the

environment. The filters are not washable nor re-useable and must

be replaced at maximum every four months. The saturation of the

active carbon filter depends on the frequency of use of the

appliance, by the type of cooking and the regularity of cleaning the

anti-grease filters.

• Clean the fan and other surfaces of the cooker hood regularly

using a cloth moistened with denatured alcohol or non abrasive

liquid detergent.

• COMANDS: 1A)LUMINOUS_1B)MECHANICAL (Fig. 5) the

key symbols are explained below:

A = LIGHT

B = OFF

C = SPEED I

D = SPEED II

E = SPEED III

F = AUTOMATIC STOP TIMER - 15 minutes

G = MOTOR WORKING indicator

The "Automatic stop timer" delays stopping of the hood, which will

continue functioning for 15 minutes at the operating speed set at

the time this function is activated.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR

EVENTUAL DAMAGES CAUSED BY BREACHING THE ABOVE

WARNINGS.

ENGLISH

Produkt Specifikationer

Mærke:	Etna
Kategori:	Emhætte
Model:	4421

Har du brug for hjælp?

Hvis du har brug for hjælp til Etna 4421 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Emhætte Etna Manualer

19 Juli 2025

8 December 2024

7 December 2024

7 December 2024

15 Oktober 2024

15 Oktober 2024

24 September 2024

1 September 2024

29 August 2024

29 August 2024

Emhætte Manualer

Nyeste Emhætte Manualer

Elica AQUA VITAE 2.0 PRF0184156 Manual

31 Juli 2025

Elica Haiku Island PRF0146280 Manual

31 Juli 2025

AEG GD3651B Manual

31 Juli 2025

Elica Era LUX PRF0189355 Manual

31 Juli 2025

Elica Bloom-S PRF0164475 Manual

31 Juli 2025

Elica BOXIN NO DRIP PRF0157280 Manual

31 Juli 2025

Elica Era STD PRF0189349 Manual

31 Juli 2025

Elica Bloom PRF0164462 Manual

31 Juli 2025

AEG NDG966AB Manual

31 Juli 2025

Elica Adéle Island PRF0167316 Manual

31 Juli 2025