Eureka Timberline Outfitter Manual

Eureka Telt Timberline Outfitter

Læs gratis den danske manual til Eureka Timberline Outfitter (2 sider) i kategorien Telt. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Eureka Timberline Outfitter, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

ASSEMBLY INSTRUCTIONS FOR THE

TIMBERLINE and TIMBERLINE OUTFITTER TENTS:

Component List:

1 Tent Body, 1 Tent Bag 4 Poles 1 Spanner

1 Tent Fly, 2 Fly Rods 1 Pole Bag

2 Junction Tubes 1 Stake Bag and Stakes

• Unroll and unfold the tent and lay it on the ground. Remove

the ﬂy and open the tent door. Do not stake down the tent just yet;

But in windy conditions, stake down one front corner into wind.

NOTE: Do not drop tent bag or pole bag on its end. Do not bounce tent

bag on its end to get tent out. These actions may cut the shock cord and/or

damage the pole ends.

• Assemble all the shock-corded poles. Make sure each pole section has ﬁrmly

seated into the adjacent section. Try to keep the poles from snapping together

as this can damage the rod ends. Through usage, the aluminum frame may

bend slightly and take a "set" this normally does not affect performance.

•

Place the tapered end of a pole onto the diagonal hole in the junction tube.

The junction tube is marked UP RT- [TOP RIGHT on TL6]- so the pole will

seat at the correct angle.

Insert a corner pin into the other end of the pole.

See fig.1.

• Repeat with the second pole and at the back of the tent with the last two

poles and the remaining junction tube.

• Disconnect the rods in the middle of the spanner. Place one end of

the spanner through the center hole of the ﬁrst junction tube. Place

the opposite end of the spanner

through the center hole in

second tube.

See fig.2.

• Push down on the disconnected

rods until they join together. This forms

the free standing frame. See fig.3.

• Connect the tent to frame by pulling the shock-corded loops, at the

peaks of the tent, over the junction tubes. Snap tent clips to the poles.

NOTE: Junction tubes can be tied to the tent with the strings provided.

Tie one end to the shock-cord loop. Pass the other end through the

1/8" hole in the junction tube and tie a knot.

See fig.4.

• Orient the tent in the desired location and stake it down.

• Fit each of the ﬂy rods over the tip of the spanner section protruding

through each junction tube.

• Drape the ﬂy over tent so the center S-hooks [ sewn on the underside

of the fly ] line up with the rods.

• Insert the center S-hook into one end of the fly rod. Pull the opposite

S-hook and insert it into the end of the second fly rod.

TIMBERLINE SERIES TENTS ARE EQUIPPED WITH

HIGH / LOW VENTING DOORS:

• To allow cool air into the tent, unzip the low vent on the door

and hold open with the hook and loop tab.

• To vent the fly, unzip the two zippers at the base of the vestibule.

• To allow warm, moist air to escape, unzip the peak of the door

and roll down and/or the peak of the back window.

OPTIONAL EQUIPMENT:

Annex: Front awning for storing gear and cooking.

Gear Loft: Mesh hammock attaches to rings inside the tent

for drying clothes or storing accessories.

Floor Saver: Place under tent to protect the ﬂoor and keep

it clean. Also provides an additional moisture barrier.

fig.1

fig.2

fig.3

fig.4

IMPORTANT:

Do not attempt this assembly with the spanner joined.

• Connect the snaps on the underside of the fly to the rings on side of

the tent. See fig.5.

• Connect four shock-corded S-hooks, located at ﬂy corners, to the

ring and pin assemblies at base of each pole.

• Stake down the two pull outs on the sides of the Fly.

See fig.6.

TL6 only

RECOMMENDATIONS:

• During strong winds, tie extra ropes [ not included ] to the

storm rings on the ﬂy and stake down securely. Note staking pattern.

See fig.6.

• Take-down task sequence:

Remove ﬂy and open door.

Disconnect hooks and peak shock-cords.

Remove clips from the tent poles; then pull the pins

out from the pole ends.

REV E 4.09

fig.6.

fig.5.

Pull out

Stake

Storm Ring

Stake

Produkt Specifikationer

Mærke:	Eureka
Kategori:	Telt
Model:	Timberline Outfitter

Har du brug for hjælp?

Hvis du har brug for hjælp til Eureka Timberline Outfitter stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Telt Eureka Manualer

Eureka El Capitan 2 Manual

6 Oktober 2024

Eureka KeeGo 2 Manual

4 Oktober 2024

Eureka KeeGo Solo Manual

30 September 2024

Eureka Tunnel Vision Grand CV Manual

9 September 2024

Eureka Hemisphere Manual

1 September 2024

Eureka Pine Lodge Manual

31 August 2024

Eureka Tetragon HD 2 Manual

19 August 2024

Eureka Dominion Manual

11 August 2024

Eureka Taron Basecamp 6 Manual

6 August 2024

Eureka Tetragon 1610 Manual

6 August 2024

Telt Manualer

Nyeste Telt Manualer

De Waard Zeester Manual

7 Oktober 2024

SereneLife SLTET30 Manual

1 Oktober 2024

Calima 46074 Manual

1 Oktober 2024

SereneLife SLPTLB106 Manual

1 Oktober 2024

SereneLife SLPTSR107 Manual

30 September 2024

Vaude Badawi Long 6 Manual

29 September 2024

De Waard Stormmeeuw Manual

25 September 2024

Vrijbuiter Stormvogel Manual

22 September 2024

Crivit IAN 86428 Manual

20 September 2024

Vrijbuiter Tannon 460 DLX Manual

20 September 2024