Extech 601500 Manual

Extech Måling 601500

Læs gratis den danske manual til Extech 601500 (1 sider) i kategorien Måling. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Extech 601500, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

601XXX-EN V1.4 9/13

pH Electrodes Instruction Sheet

Models 601100, 601500 and 60120B

Electrode Specifications

Model number 601100 60120B 601500

Description Flat surface combination pH

electrode with gelled reference

solution

Mini combination pH electrode with

sealed gelled reference filling

solution and detachable bulb guard

General-purpose combination pH

electrode with sealed gelled reference

filling solution and detachable bulb guard

Dimensions 15 x 115 mm 10 x 126 mm 12.5 x 155 mm

Construction material Polymer housing, flat glass bulb Polymer housing, glass bulb Polymer housing, glass bulb

Measuring range 0 to 14.0 pH units 0 to 14.0 pH units 0 to 14.0 pH units

Temp. range 0-80

C 0-80

Reference junction Teflon Ceramic Ceramic

Reference type Ag/AgCl (silver silver chloride) Ag/AgCl (silver silver chloride)Ag/AgCl (silver silver chloride)

Isopotential point ~7.0 pH ~7.0 pH ~7.0 pH

Precision 0.02 pH units 0.02 pH units 0.02 pH units

Connector BNC BNC BNC

Cable length 1 meter (39”) 1 meter (39”) 1 meter (39”)

Storage container Bottle Cap Bottle

General Electrode Procedure

1. To avoid damage to the electrode when removing it from or

inserting it into the soaking bottle;

a) Unscrew the bottle cap.

b) Remove the electrode and cap from the bottle.

c) Slide the cap off the electrode.

d) Reverse this procedure when storing the electrode.

2. Rinse the electrode with deionized or distilled water.

3. Carefully shake electrode to ensure that any air bubbles in the

bulb or lower stem of the electrode are dislodged upwards.

4. Blot electrode with tissue.

5. Connect electrode to pH meter and follow the pH meter

manufacturer’s instruction for calibration.

Before Measurement

1. Generally, the sample should be aqueous and fall within the

range 0 – 14 pH

2. Always use fresh buffers for calibration. Choose buffers that are

no more than 3 pH units apart.

3. To obtain the maximum precision, always buffer as close as

possible to the expected measured value.

4. Between measurements, rinse electrodes with distilled water and

then with the next solution to be measured.

5. Stir all buffers and samples.

6. Avoid rubbing or wiping electrode bulb in order to reduce the

chance of error due to polarization.

pH Calibration and Measurement

Refer to the owner’s guide from the manufacturer of the pH meter

being used for detailed information regarding calibration and

temperature compensation procedures.

Two-Buffer Calibration (for high precision measurements)

1. Set up the pH meter according to the manufacturer’s instruction

manual.

2. Ensure that all buffers are at the same temperature (+/- 2

C.) If

samples are at varying temperatures, temperature compensation

is recommended. (See pH meter instruction manual.)

3. Select two buffers that bracket the expected pH value. The first

should be near the electrode isopotential point (pH 7) and the

second near the expected pH of the sample. (e.g., pH 4 or 10.)

4. Rinse the electrode first with distilled water and then with pH 7

buffer. Place the electrode in the pH 7 buffer.

5. Wait for a stable pH 7 reading. Set the pH meter to the pH value

of the buffer at its measured temperature.

6. Rinse the electrode first with distilled water and then with the

second buffer. Place the electrode in the second buffer.

7. Wait for a stable display. Set the pH meter to the pH value of the

buffer at its measured temperature.

8. Calibration is complete. Proceed to pH measurement

Single-Buffer Calibration (for lower precision measurements)

1. Set up the pH meter according to the manufacturer’s instruction

manual.

2. Choose a buffer that has a value close to the expected pH of the

sample.

Rinse the electrode first in distilled water and then in the buffer being used

for calibration. Place the electrode in the buffer.

4. Wait for a stable display. Set the pH meter to the pH value of the buffer at

its measured temperature.

5. Proceed to pH measurement

pH Measurement

1. Calibrate the electrode as described in previous section.

2. Rinse the electrode with distilled water and then with the sample solution.

3. Place the electrode in the sample.

4. Stir the sample.

5. When the reading is stable, record the pH value.

Electrode Storage and Maintenance

Electrode Storage

1. Electrodes 601100 and 601500

Store in the soaking bottle. The soaking solution should be 22.4g

KCl dissolved in 100ml pH4 buffer solution or 25g KCl dissolved

in 100ml pure water.

2. Electrode 60120B

Store with wetting cap kept damp with pH4 buffer or, alternatively,

store in a soaking solution.

Electrode Maintenance

3. Inspect the electrode for scratches, cracks, salt crystal build-up,

or membrane/junction deposits.

4. Rinse off any salt build-up with distilled water, and remove any

membrane/junction deposits as directed in cleaning procedures

below.

5. Drain the reference chamber, flush it with fresh filling solution and

refill the chamber

Cleaning Procedures

Soak in mild detergent or dilute 0.1M HCl for 30 minutes

Electrode Reconditioning

If the electrode has been allowed to dry for any period of time it

may require reconditioning. Soak the electrode in a pH 4 buffer

solution for at least 20 minutes. Depending on the dryness of the

reference junction, this reconditioning process may require up to a

24 hour soaking period in order to obtain accurate pH readings.

Warranty

FLIRSystems, InstrumentsInc.warrantsthisExtech branddevice   to be free ofdefects

inpartsand workmanship for        oneyear from date of shipment (a six month limited

warrantyappliestosensorsandcables).Ifitshouldbecomenecessarytoreturnthe

instrumentforserviceduringorbeyond the warranty

 period, contact  the Customer

ServiceDepartmentforauthorization.Visitthewebsitewww.extech.com for contact

information.A       Return Authorization (RA) number must be issued beforeanyproduct is

returned.Thesenderisresponsibleforshippingcharges,freight,  insurance and proper

packagingtopreventdamageintransit.Thiswarrantydoesnotapplytodefects

resultingfromactionoftheusersuchasmisuse,improperwiring,operationoutside

 of

specification,impropermaintenanceor orrepair, unauthorizedmodification.FLIR

Systems,Inc.specificallydisclaims any    implied warranties or merchantability  or fitness

for a specificpurposeandwillnot be      liable for any direct, indirect, incidentalor

consequentialdamages.FLIR’s    total liability is limited to  repair or replacementofthe

product.

Thewarrantysetforthaboveis inclusive andnootherwarranty,whether

written      or oral, is expressed or implied.

Produkt Specifikationer

Mærke:	Extech
Kategori:	Måling
Model:	601500

Har du brug for hjælp?

Hvis du har brug for hjælp til Extech 601500 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Måling Extech Manualer

Extech HDV-TX2L Manual

2 December 2025

1 December 2025

1 December 2025

1 December 2025

1 December 2025

1 December 2025

1 December 2025

1 December 2025

1 December 2025

1 December 2025

Måling Manualer

Nyeste Måling Manualer

Vevor EM4556 Manual

1 December 2025

Vevor SD317 Manual

1 December 2025

Vevor SD308 Manual

1 December 2025

Terraillon Fast Track Manual

1 December 2025

Seaward PV:1525 Manual

30 November 2025

FLIR E75 Manual

28 November 2025

Bosch GLM 40-31 Professional Manual

28 November 2025

Terraillon COACH Manual

27 November 2025

FLIR T530 Manual

27 November 2025

FLIR TG268 Manual

27 November 2025