Faber Axia Isola Manual

Faber Emhætte Axia Isola

Læs gratis den danske manual til Faber Axia Isola (17 sider) i kategorien Emhætte. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Faber Axia Isola, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/17

Version 3/08 - Page 1

Axia Isola

Island Mount Canopy Rangehood

READ THESE INSTRUCTIONS BEFORE YOU START INSTALLING THIS RANGEHOOD

WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: a) Never leave surface units unattended at high set-

tings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium setting. b) Always

turn hood ON when cooking at high heat or when ambeing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef

Flambé). c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or lter. d) Use proper

pan size. Always use cookware appropriate for the size of the surface element.

WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE

THE FOLLOWING: SMOTHER FLAMES with a close-tting lid, cookie sheet, or metal tray, then turn off the burner. BE CARE-

FUL TO PREVENT BURNS. If the ames do not go out immediately EVACUATE AND CALL THE FIRE DEPARTMENT. NEVER

PICK UP A FLAMING PAN - You may be burned. DO NOT USE WATER, including wet dishcloths or towels - a violent steam

explosion will result. Use an extinguisher ONLY if: 1. You know you have a Class ABC extinguisher, and you already know

how to operate it. 2. The re is small and contained in the area where it started. 3. The re department is being called. 4.

You can ght the re with your back to an exit.

ALL WALL AND FLOOR OPENINGS WHERE THE RANGEHOOD IS INSTALLED MUST BE SEALED.

This rangehood requires at least 24" of clearance between the bottom of the rangehood and the cooking surface or countertop. This

minimum clearance may be higher depending on local building code. For example, for gas ranges, a minimum of 30" may be required.

The maximum depth of overhead cabinets is 13". Overhead cabinets on both sides of this unit must be a minimum of 18" above the

cooking surface or countertop. Consult the cooktop or range installation instructions given by the manufacturer before making any

cutouts. MOBILE HOME INSTALLATION The installation of this rangehood must conform to the Manufactured Home Construction

and Safety Standards, Title 24 CFR, Part 3280 (formerly Federal Standard for Mobile Home Construction and Safety, Title 24, HUD,

Part 280). Four wire power supply must be used and the appliance wiring must be revised. See Electrical Requirements.

LISEZ BIEN CETTE FICHE AVANT D'INSTALLER LA HOTTE

AVERTISSEMENT - POUR MINIMISER LE RISQUE D’UN FEU DE GRAISSE SUR LA TABLE DE CUISSON : a) Ne jamais laisser

un élément de la table de cuisson fonctionner sans surveillance à la puissance de chauffage maximale; un renversement/

débordement de matière graisseuse pourrait provoquer une inammation et le génération de fumée. Utiliser toujours une

puissance de chauffage moyenne ou basse pour le chauffage d’huile. b) Veiller à toujours faire fonctionner le ventilateur de

la hotte lors d’une cuisson avec une puissance de chauffage élevée ou lors de la cuisson d’un mets à amber (i.e. Crepes

Suzette, Cherries Jubilee, Peppercorn Beef Flambé). c) Nettoyer fréquemment les ventilateurs d’extraction. Veiller à ne pas

laisser de la graisse s’accumuler sur les surfaces du ventilateur ou des ltres. d) Utiliser toujours un ustensile de taille ap-

propriée. Utiliser toujours un ustensile de taille adapté à la taille de l’élément chauffant.

AVERTISSEMENT: - POUR PRÉVENIR LES BLESSURES EN CAS DE FEU SUIVRE LES RECOMMANDATIONS SUIVANTES:

ÉTOUFFEZ LE FEU avec un couvercle métallique et fermez le brûleur. Si le feu ne s'éteint pas tout de suite, QUITTEZ LES

LIEUX ET APPELEZ LES POMPIERS. NE TOUCHEZ JAMAIS UNE CASSEROLE EN FLAMMES. N'UTILISEZ JAMAIS DE L'EAU

ou un torchon mouillé pour éteindre le feu - ce qui pourrait causer une explosion de vapeur. N'utilisez un extincteur que

si: 1. Vous avez un modèle ABC et vous connaissez bien son mode d'emploi. 2. Le feu est petit et peu répandu. 3. Les

pompiers sont déjà prévenus. 4. Vous avez une sortie derrière vous.

TOUTE OUVERTURE DANS LE MUR OU LE PLANCHER À PROXIMITÉ DE LA HOTTE DOIT ÊTRE SCELLÉ

Gardez 24 po. de hauteur entre le bas de la hotte et la surface de cuisson. Cette hauteur minimum peut être haute suivant le code

municipal. Par exemple, les cuisinières à gaz peuvent requérir 30 po. de hauteur. Les armoires au-dessus ne dépasseront pas 13 po.

de profondeur. Les armoires au-dessus de chaque côté devront être au moins à 18 po. au-dessus de la surface de cuisson. Consultez

la che technique avant de découper les armoires. L'installation de cette hotte doit être conforme aux Réglements de Manufactured

Home Construction and Safety Standards, titre 24 CFR, Section 3280 (anciennement Federal Standard for Mobile Home Construction

and Safety Standards, titre 24 CFR, Section 3280 (anciennement Federal Standard for Mobile Home Construction and Safety, titre 24,

HUD, Section 280). Le branchement électrique se fait avec une raccordement à 4 ls. Consultez la che technique électrique.

READ AND SAVE THESE INSTRUCTIONS

The Installer must leave these instructions with the homeowner.

The homeowner must keep these instructions for future reference

and for local electrical inspectors' use.

• Installation Instructions

• Use and Care Information

Version 3/08 - Page 2

VENTING REQUIREMENTS

Determine which venting method is best for your application.

Ductwork can extend either through the wall or the roof.

The length of the ductwork and the number of elbows should

be kept to a minimum to provide efcient performance. The

size of the ductwork should be uniform. Do not install two el-

bows together. Use duct tape to seal all joints in the ductwork

system. Use caulking to seal exterior wall or oor opening

around the cap.

Flexible ductwork is not recommended. Flexible ductwork

creates back pressure and air turbulence that greatly

reduces performance.

Make sure there is proper clearance within the wall or oor for

exhaust duct before making cutouts. Do not cut a joist or stud

unless absolutely necessary. If a joist or stud must be cut, then

a supporting frame must be constructed.

FOR MORE SPECIFIC DUCTWORK INFORMATION, GO

TO PAGE 4.

WARNING - To Reduce The Risk Of Fire, Use Only Metal

Ductwork.

ELECTRICAL REQUIREMENTS

A 120 volt, 60 Hz AC-only electrical supply is required on a

separate 15 amp fused circuit. A time-delay fuse or circuit

breaker is recommended. The fuse must be sized per local

codes in accordance with the electrical rating of this unit as

specied on the serial/rating plate located inside the unit near the

eld wiring compartment. THIS UNIT MUST BE CONNECTED

WITH COPPER WIRE ONLY. Wire sizes must conform to the

requirements of the National Electrical Code, ANSI/NFPA 70

- latest edition, and all local codes and ordinances. Wire size

and connections must conform with the rating of the appliance.

Copies of the standard listed above may be obtained from:

National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

• Venting system MUST terminate outside the

home.

• DO NOT terminate the ductwork in an attic or

other enclosed space.

• DO NOT use 4" laundry-type wall caps.

• Flexible-type ductwork is not recommended.

• DO NOT obstruct the ow of combustion and

ventilation air.

• Failure to follow venting requirements may result

in a re.

This appliance should be connected directly to the fused discon-

nect (or circuit breaker) through exible, armored or nonmetallic

sheathed copper cable. Allow some slack in the cable so the

appliance can be moved if servicing is ever necessary. A UL

Listed, 1/2" conduit connector must be provided at each end

of the power supply cable (at the appliance and at the junction

box).

When making the electrical connection, cut a 1 1/4" hole in the

wall. A hole cut through wood must be sanded until smooth. A

hole through metal must have a grommet.

WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, do not use this fan with any solid-state speed

control device.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRI-

CAL SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING: Use this unit only in the manner intended

by the manufacturer. If you have any questions, contact

the manufacturer.

Before servicing or cleaning unit, switch power off at

service panel and lock the service disconnecting means

to prevent power from being switched on accidentally.

When the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a tag,

to the service panel.

CAUTION: For General Ventilating Use Only. Do Not Use To

Exhaust Hazardous or Explosive Materials and Vapors.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRI-

CAL SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING: Installation Work And Electrical Wiring Must

Be Done By Qualied Person(s) In Accordance With All

Applicable Codes And Standards, Including Fire-Rated

Construction.

Sufcient air is needed for proper combustion and exhaust-

ing of gases through the ue (chimney) of fuel burning

equipment to prevent backdrafting. Follow the heating

equipment manufacturer's guideline and safety standards

such as those published by the National Fire Protection

Association (NFPA), and the American Society for Heating,

Refrigeration and Air Conditioning Engineers (ASHRAE),

and the local code authorities.

When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

Ducted fans must always be vented to the outdoors.

WARNING

• Electrical ground is required on this rangehood.

• If cold water pipe is interrupted by plastic,

nonmetallic gaskets or other materials, DO NOT

use for grounding.

• DO NOT ground to a gas pipe.

• DO NOT have a fuse in the neutral or grounding

circuit. A fuse in the neutral or grounding circuit

could result in electrical shock.

• Check with a qualied electrician if you are in doubt

as to whether the rangehood is properly grounded.

• Failure to follow electrical requirements may result

in a re.

WARNING

For residential use only.

Cold Weather installations

An additional back draft damper should be installed to minimize

backward cold air ow and a nonmetallic thermal break should

be installed to minimize conduction of outside temperatures

as part of the vent system. The damper should be on the cold

air side of the thermal break. The break should be as close as

possible to where the vent system enters the heated portion

of the house.

Produkt Specifikationer

Mærke:	Faber
Kategori:	Emhætte
Model:	Axia Isola

Har du brug for hjælp?

Hvis du har brug for hjælp til Faber Axia Isola stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Emhætte Faber Manualer

Faber Fabula W Plus Manual

9 August 2025

Faber Tender 60 X Manual

9 August 2025

Faber The Heaven 3.0 Slim Manual

21 Juli 2025

Faber The Heaven 2.0 Manual

21 Juli 2025

Faber The Beat Manual

21 Juli 2025

Faber The Cylindra Isola Manual

21 Juli 2025

Faber The Heaven Glass 2.0 90cm Manual

21 Juli 2025

Faber The Chloé Isola Manual

21 Juli 2025

Faber The Pareo Plus Manual

21 Juli 2025

Faber The Skypad 2.0 Manual

21 Juli 2025

Emhætte Manualer

Nyeste Emhætte Manualer

Pando E-237 Manual

17 August 2025

Zephyr Anzio ZAZ-M90DS Manual

17 August 2025

Pando E-201 Manual

17 August 2025

Trade-Wind P32366RC Manual

17 August 2025

NuTone NCDA130WW Manual

17 August 2025

Pando E-221 Manual

17 August 2025

Porter & Charles GLIDE-24-2 Manual

17 August 2025

Elica PRF0161680 Manual

17 August 2025

KKT Kolbe PLUS430 Manual

17 August 2025

KKT Kolbe UBH600B Manual

17 August 2025