Fluke 1AC II Manual

Fluke Ikke kategoriseret 1AC II

Læs gratis den danske manual til Fluke 1AC II (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Fluke 1AC II, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

PN 3497693

July 2009 Rev. 1, 8/20

Specifications are subject to change without notice.

1AC II

VoltAlert

Instruction Sheet

Read First: Safety Information

 Warning

To prevent possible electric shock or personal injury:

• Read all safety information before you use the Product.

• Do not rely on the Tester to detect the presence or absence of voltage on a

conductor for safety purposes. A single pole non-contact voltage detector such as

this Tester is NOT suitable to determine if a circuit is hazardous. A volt meter or

2-pole voltage detector is necessary to confirm the absence of hazardous voltage

prior to commencing work

• Hold the Product behind the tactile barrier.

• Do not use the Product around explosive gas, vapor, or in damp or wet

environments.

• Replace all alkaline batteries with fresh batteries of the same manufacturer and type

to prevent battery leakage.

• Remove the alkaline batteries if the Product is not used for an extended period of

time, or if stored in temperatures above 50 °C. If the batteries are not removed,

battery leakage may result.

• Repair the Product before use if the battery leaks. Battery leakage may create a

shock hazard or damage the Product.

• Alkaline batteries contain hazardous chemicals that can cause burns. If exposure to

chemicals occurs, clean with water and get medical aid.

• If the Tester is used in a manner not specified by the manufacturer, protection

provided by the Tester may be affected.

• Do not use if VoltBeat is not flashing.

• Test on a known live source within the rated ac voltage range of the product, both

before and after use to ensure unit is in good working condition.

• When using the Tester, if tip does not glow, voltage could still be present. The Tester

indicates active voltage in the presence of AC electric fields of sufficient strength

emanating from the conductor. If the field strength is low, the Tester may not provide

indication of live voltages. Lack of an indication occurs if the Tester is unable to

sense the presence of electric field which may be influenced by several factors the

including, but not limited to:

• Shielded wire/cables

• Thickness and type of insulation

• Distance from the voltage source

• Fully-isolated users that prevent an effective ground

• Receptacles in recessed sockets/ differences in socket design

• Condition of the Tester and Batteries

• Do not use if the Tester appears damaged or if the Tester is not operating properly.

Specifically examine the probe tip for cracks or breakage before use. If in doubt,

have the Tester serviced.

• Do not apply more than the rated voltage as marked on the Tester.

• Use caution with voltages above 30 V ac as a shock hazard may exist.

• Comply with local and national safety codes. Use personal protective equipment

(approved rubber gloves, face protection, and flame-resistant clothes) to prevent

shock and arc blast injury where hazardous live conductors are exposed.

Safety: IEC 61010-1: Pollution Degree 2; IEC 61010-2-030: CAT IV 1000 V

Electromagnetic Environment: IEC 61326-1: Portable Electromagnetic Environment;

CISPR 11: Group 1, Class B

Electromagnetic Compatibility: Applies to use in Korea only. Class A Equipment (Industrial

Broadcasting & Communication Equipment)

[1]

[1] This product meets requirements for industrial (Class A) electromagnetic wave equipment

and the seller or user should take notice of it. This equipment is intended for use in business

environments and is not to be used in homes.

Voltage Detection Range:

Model

Region

Range

A1/A2

N. America, S. America, Asia

90 V ac to 1000 V ac

E1/E2

Europe

200 V ac to 1000 V ac

L (low voltage) AC

N. America

20 V ac to 90 Vac

China

90 V ac to 1000 V ac

FOR USE BY COMPETENT

PERSONS

Anyone using this instrument should be

knowledgeable and trained about the risks

involved with measuring voltage, especially

in an industrial setting, and the importance of

taking safety precautions and of testing the

instrument before and after using it to ensure

that it is in good working condition.

Produkt Specifikationer

Mærke:	Fluke
Kategori:	Ikke kategoriseret
Model:	1AC II

Har du brug for hjælp?

Hvis du har brug for hjælp til Fluke 1AC II stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Fluke Manualer

Fluke MicroMapper Manual

25 November 2025

Fluke GFL-1500 Manual

19 November 2025

Fluke FiberLert-125 Manual

19 November 2025

Fluke 1630-2 FC Manual

25 August 2025

2 August 2025

2 August 2025

2 August 2025

2 August 2025

2 August 2025

2 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Savage FireMixer-14 Manual

5 December 2025

Stone Espresso Lite Manual

5 December 2025

Luna Optics LN-G2-M50 Manual

5 December 2025

Origin Effects Halcyon Blue Overdrive Manual

5 December 2025

Ferplast Twist G Manual

5 December 2025

Vevor ZY-40X12-4Black Manual

5 December 2025

Steiner Mk7 Battle Light Manual

5 December 2025

Dual VK9 Manual

5 December 2025

Crestron HZ-FP-G4 Manual

5 December 2025

Joyo R-09 Vision Dual Mod Manual

5 December 2025