Fluke i3000s Flex Manual

Fluke Ikke kategoriseret i3000s Flex

Læs gratis den danske manual til Fluke i3000s Flex (10 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Fluke i3000s Flex, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/10

i3000s/i2000 Flex

AC Current Probe

Instruction Sheet

Introduction

The i3000s 24 Flex, i3000s 36 Flex, and i2000 Flex AC Current

Probes (the Probe) are used with oscilloscopes, digital

multimeters, recorders or data loggers. The i3000s probes can

be used to measure AC current up to 3000 A. The i2000 can be

used to measure AC current up to 2000 A. The flexible

measuring head allows current measurements on conductors

that are hard to reach or inaccessible using typical clamp-on

current probes.

The Probes provide a low-voltage (3 V AC for i3000s models,

and 2 V AC for i2000) output that is proportional to the current

being measured. The Probes provide full-scale direct readings

for 30 A, 300 A, and 3000 A when using the i3000s models, and

20 A, 200 A, and 2000 A when using the i2000.

Safety Instructions

A Warning identifies conditions and procedures that are

dangerous to the user. A Caution identifies conditions and

procedures that can cause damage to the Product or the

equipment under test.

 Warning

To prevent electric shock or personal injury:

• Use the Current Probe only as specified in the

operating instructions; otherwise the current

probe’s safety features may not protect you.

• Use the Probes only if qualified.

• Use caution during installation and use of the

Probe; high voltages and currents may be

present in circuit under test.

• Have maintenance performed by only qualified

service personnel.

PN 2560447

March 2006, Rev. 1, 4/17

Specifications are subject to change without notice.

All product names are trademarks of their respective companies.

• Protect the probe against water and humidity.

• Wear protective clothing and gloves as

required.

• Do not install this product on live conductors.

Always de-energize the circuit under test before

installing the flexible measuring head.

• Always inspect the electronics unit, connecting

cable, and flexible measuring head for damage

before using the Probe.

• Do not use the Probe if damaged.

• Always connect Probe to display device before

installing the flexible measuring head.

• Never change batteries while measurement

head is installed on conductor.

• Use only the provided original or specified

accessories.

• Use the Current Probe only as specified in the

operating instructions; otherwise the current

probe’s safety features may not protect you.

• Adhere to local and national safety codes.

Individual protective equipment must be used

to prevent shock and arc blast injury where

hazardous live conductors are exposed.

• CAT III equipment is designed to protect against

the transients in the equipment in fixed

equipment installations, such as distribution

panels, feeders and short branch circuits, and

the lighting systems in large buildings.

Produkt Specifikationer

Mærke:	Fluke
Kategori:	Ikke kategoriseret
Model:	i3000s Flex
Vægt:	190 g
Antal pr. pakke:	1 stk
Produktfarve:	Black,Red,Yellow
Produkttype:	Strømklemme
Ledningslængde:	2 m
Opbevaringstemperatur (T-T):	-20 - 85 °C
Driftstemperatur (T-T):	-20 - 85 °C
Materiale:	Polypropylene (PP),Thermoplastic elastomer (TPE)
Certificering:	BS EN 61010-1: 2001\nBS EN 61010-2-032: 2002\nBS EN 61010-031: 2002
Længde:	610 mm
Stik:	BNC
Dobbeltisoleret:	Ja
Strøm (maks.):	3000 A
Nominel spænding:	600 V
Målekategori understøttes:	CAT III
Maksimal driftshøjde:	2000 m