Fluke i410 Manual

Fluke Ikke kategoriseret i410

Læs gratis den danske manual til Fluke i410 (10 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Fluke i410, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/10

i410/i1010

AC/DC Current Clamp

Service Information

WWarning

To avoid electric shock:

• Do not service this Current Clamp unless you are qualified to do so.

The service information provided in this document is for use by quali-

fied personnel only.

• Always remove input signals from the Current Clamp before opening

the case.

• Be careful when working with voltages that exceed 30V ac rms, 42.4V

pk, or 60V dc.

• The Current Clamp is protected throughout by double insulation. When

servicing the Current Clamp, use only specified replacement parts.

Caution

• If the Current Clamp is to be Calibrated, you must have a replacement

decal. See the Replacement Parts section for further details.

• This Current Clamp contains parts that can be damaged by static dis-

charge. Follow the standard practices for handling static sensitive de-

vices.

Introduction

Service Information covers the following service-related areas for the i410/i1010 AC/DC Current

Clamps:

• Product specifications

• Required equipment

• Performance test procedure and test values

• Preparing for calibration

• Calibration procedure

• Reassembly procedure

• Replacement parts

Usually, service information in this document applies to both models (i410 and i1010). Information ap-

plicable to only one model is so noted. For operating information, refer to the Instruction Sheet that came

with the Current Clamp.

i410/i1010

AC/DC Current Clamp

Service Under Warranty

The Current Clamp is warranted to be free from defects in material and workmanship for one year.

The warranty does not cover abuse, batteries, or damage caused by using the Current Clamp outside its

rated specifications or operating environment. The complete warranty statement appears in the Current

Clamp Instruction Sheet.

For repairs:

• In the USA or Canada, call 1-800-323-5700

• Outside the USA, contact your nearest Fluke Distributor or Service Center.

Service, repairs, and replacement parts are warranted for 90 days.

Specications

General specifications are shown in Table 1. Range and accuracy specifications are shown in Table 2.

The accuracy of the Current Clamp is specified for one year after calibration, at 18°C to 28°C (64°F to

82°F), with relative humidity to 90%.

Table 1. General Specifications

Operating Temperature -10 to 50°C (14 to 122°F) Current x Hz Product ≤ 240,000

Storage Temperature Output Signal-20 to 60°C (-4 to 140°F) 1 mV per amp dc or ac

Relative Humidity 0 to 95% (0 to 30°C)

0 to 75% (30 to 40°C)

0 to 45% (40 to 50°C)

Working Voltage 600V CAT. III

maximum at input

Altitude

Operating

Non-operating

0 - 2000m

0 - 12000m

Maximum Conductor

Size

1 ea. 30 mm (1.18 in.)

diameter

2 ea. 25 mm (0.98 in.)

diameter

Battery Type 9V (alkaline) Load Impedance ≥ Ω1 M , ≤100 pF

Battery Life 60 hrs typical (continuous

with alkaline)

Temperature

Coefficient

+/-(0.05 x accuracy per °C

(0 -18°C, 28-50°C)

Safety s Double Insulation, 600V,

CAT. III

Size 209 x 78 x 48 mm (3.09 x

8.21 x 1.87 in.)

Weight 0.5 kg (17.6 oz.)

Table 2. Range and Accuracy Specifications

i410 i1010

Specied Current Range 1 - 400A ac rms *

1 - 400A dc

1 - 600A ac rms *

1 - 1000A dc

Usable Current Range 0.5 - 400A 0.5 - 1000A

DC Accuracy (zero adjusted,

conductor centered)

3.5% + 0.5A (0 - 400A) 2.0% + 0.5A (0-1000A)

AC Accuracy 3.5% + 0.5A, 45 - 400 Hz, Crest

Factor 3.≤

(1 - 400A)

2.0% + 0.5A, 45 - 400 Hz, Crest Factor 3.≤

3.0% + 0.5A, 400 Hz - 2 kHz sine wave.

(1 - 600A)

Bandwidth 3 kHz 10 kHz

With a true-rms DMM, the minimum ac current is limited to the low end of the specified mV ac range.

Produkt Specifikationer

Mærke:	Fluke
Kategori:	Ikke kategoriseret
Model:	i410

Har du brug for hjælp?

Hvis du har brug for hjælp til Fluke i410 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Fluke Manualer

18 Juni 2025

14 Juni 2025

11 Marts 2025

8 Oktober 2024

8 Oktober 2024

8 Oktober 2024

8 Oktober 2024

7 Oktober 2024

4 Oktober 2024

Fluke CableAnalyzer DSX-8000 Manual

1 Oktober 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Zoom A3 Manual

16 Juli 2025

DS18 SLG-FKP6 Manual

16 Juli 2025

CYP PU-1201-KIT Manual

16 Juli 2025

JUNG 4008 TSM Manual

16 Juli 2025

Emko SMR1P1-00-00-01-00 Manual

16 Juli 2025

DS18 Hydro NXL-X6TP Manual

16 Juli 2025

CYP PUV-1350PL-TXWP Manual

16 Juli 2025

Audio Pro VOL-1 Manual

16 Juli 2025

CYP PUV-2010TXWP Manual

16 Juli 2025

Hillvert HT-VC-400 Manual

16 Juli 2025