Fluke i6000s Flex Manual

Fluke Ikke kategoriseret i6000s Flex

Læs gratis den danske manual til Fluke i6000s Flex (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Fluke i6000s Flex, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

i 6000s Flex

AC Current Probe

Instruction Sheet

Introduction

The i6000s 24 Flex and i6000s 36 Flex C P s (tAC urrent robe he

Probe) are used with oscilloscopes, digital multimeters, recorders

or data loggers. can be used to measure AC current PThe robes

up to 6000 A. The flexible measuring head allows current

measurements on conductors that are hard to reach or

inaccessible using typical on current probes.clamp-

The Probes provide a low voltage (3- V ac) output that is

proportional to the current being measured. The provideProbes

full-scale direct readings for 60 A, 600 A, and 6000 A.

Safety Instructions

A Warning identifies conditions and procedures that are

dangerous to the user. A Caution identifies conditions and

procedures that can cause damage to the Product or the

equipment under test.

 Warning

To prevent electric shock or personal injury:

• If the Probes are used in a manner not

specified in these operating instructions,

protection provided by the Probes may be

impaired.

• Use the Probes only if qualified.

• Use caution during installation and use of the

Probes; high voltages and currents may be

present in circuit under test.

• Have maintenance performed by only qualified

service personnel.

• Protect the Probes against water and

humidity.

PN 2842359

June 200 7, Rev. 2 6/21 ,

S pecifications are subject to change without notice.

All product names are trademarks of their respective companies.

• Wear protective clothing and gloves as

required.

• Do not install this product on live conductors.

Always de- zenergi e the circuit under test

before installing the flexible measuring head.

• Always inspect the electronics unit,

connecting cable, and flexible measuring head

for damage before using the Probe.

• Do not use the Probe if damaged.

• Always connect Probe to display device

before installing the flexible measuring head.

• Never change batteries while measurement

head is installed on conductor.

• Use only the provided original or specified

accessories.

• Comply with local and national safety codes.

Use personal protective equipment (approved

rubber gloves, face protection, and flame-

resistant clothes) to prevent shock and arc

blast injury where hazardous live conductors

are exposed.

• CAT III equipment is designed to protect

against the transients in the equipment in

fixed equipment installations, such as

distribution panels, feeders and short branch

circuits, and the lighting systems in large

buildings.

Produkt Specifikationer

Mærke:	Fluke
Kategori:	Ikke kategoriseret
Model:	i6000s Flex

Har du brug for hjælp?

Hvis du har brug for hjælp til Fluke i6000s Flex stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Fluke Manualer

Fluke 1630-2 FC Manual

25 August 2025

2 August 2025

2 August 2025

2 August 2025

2 August 2025

2 August 2025

2 August 2025

2 August 2025

Fluke FibertLert-125 Manual

1 August 2025

Fluke SmartTrace BK120 Manual

20 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Salton MP1206 Manual

31 August 2025

TensCare Sports TENS 2 Manual

31 August 2025

Pardini K58 Manual

31 August 2025

Salton SCG-4 Manual

31 August 2025

Salton JK-1103 Manual

31 August 2025

Salton WC-2040 Manual

31 August 2025

Salton WC-2070 Manual

31 August 2025

Salton SP1963 Manual

31 August 2025

Gram EFI 8060-91 B Manual

31 August 2025

Analog Way Orchestra² Manual

31 August 2025