Fluke SV225 Manual

Fluke Ikke kategoriseret SV225

Læs gratis den danske manual til Fluke SV225 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 15 anmeldelser. Har du et spørgsmål om Fluke SV225, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Instruction Sheet

SV225

Stray Voltage Eliminator

CAT

600

Introduction

The SV225 Stray Voltage Eliminator (hereafter referred to as

“the Adapter”) is a digital multimeter accessory that allows

measurements in circuits which may be subject to stray

voltages encountered from adjacent-energized wiring.

The Adapter provides an approximate 3,000 e load to the

measured circuit, desensitizing the meter to low energy,

spurious sources of interference. The Adapter is only used for

voltage measurements. When used with a compatible digital

multimeter, it can be determined whether the circuits under test

are energized or not.

Safety Information

XW Read First: Safety Information

To avoid possible electric shock or personal

injury:

• Read the operating instructions before use

and follow all safety instructions.

• Use caution when working with voltages

above 60 V dc or 30 V ac. Such voltages pose

a shock hazard.

• Before testing the desired circuit, ensure that

the multimeter and Adapter are functioning

properly by testing a known live circuit. A de-

energized circuit will be indicated on the

multimeter display as a reading near zero

volts.

• When using the Adapter to eliminate stray or

ghost voltage, the Adapter has a low input

impedance, nominally 3,000 Ω

Ω

ΩΩ. This low

impedance places a moderate load on the

circuit under test. Do not use the Adapter to

measure live voltages in circuits that could be

damaged by a 3 kΩ

Ω

ΩΩ load.

PN 2429231

March 2005 Rev.1, 11/05

All product names are trademarks of their respective companies.

• Do not apply more than the rated voltage, as

marked on the multimeter or in the Adapter

specifications (whichever is lower) between

the terminals, or between any terminal and

earth ground.

• Before each use, inspect test leads for

damage and check for continuity. Do not use

leads that are damaged or show high

resistance. Look for cracks or missing plastic

on the lead housing or cable insulation.

• Adhere to local and national safety codes.

• Individual protective equipment must be used

to prevent shock and injury.

• If the equipment is used in a manner not

specified by the manufacturer, the protection

provided by the equipment may be impaired.

• The Adapter is specified for CAT III

1000V/CAT IV 600V per EN61010.

• CAT III equipment is designed to protect

against transients in equipment in fixed-

equipment installations, such as distribution

panels, feeders and short branch circuits, and

lighting systems in large buildings.

• CAT IV equipment is designed to protect

against transients from the primary supply

level, such as an electricity meter or an

overhead or underground utility service.

Symbols

The following symbols appear on the Adapter or in this

instruction sheet.

T Product is protected by double insulation.

W Risk of Danger. Important information. See

Instruction Sheet.

X Hazardous voltage.

;

N10140 Conforms to relevant Australian standards.

P Conforms to relevant European Union directives.

Specifications

Voltages up to 1000 volts continuous can be safely applied to

the Adapter without damage.

Operation Temperature

-20 °C to +55 °C (-40 °F to 131 °F)

Altitude

2,000 Meters Operating

Humidity

90 % at 0 to 35 ° ° °C (32 F to 95 F), 70 % at 35 to 55 °C

(95 °F to 131 °F)

Nominal Resistance

3,000 Ω @ 25 °C (77 °F)

Instrument Compatibility

The Adapter is for use with any high-impedance digital

multimeter (≥ 1 M ) which accepts 4 mm safety-shrouded Ω

banana plugs and with any test leads using the same safety-

shrouded banana plugs. The Adapter is compatible with the

following Fluke digital multimeters and testers:

• Fluke 27

• 70 Series

• 80 Series

• Fluke-110 Series

• 170 Series

• 180 Series

Produkt Specifikationer

Mærke:	Fluke
Kategori:	Ikke kategoriseret
Model:	SV225
Produktfarve:	Black,Red,Yellow
Driftstemperatur (T-T):	-20 - 55 °C
Certificering:	CE
Nominel spænding:	1000 V
Målekategori understøttes:	CAT III,CAT IV
Maksimal driftshøjde:	2000 m
Intern modstand:	3000 ohm (Ω)