Fluke T110 Manual

Fluke Ikke kategoriseret T110

Læs gratis den danske manual til Fluke T110 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 55 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 28 anmeldelser. Har du et spørgsmål om Fluke T110, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

T90/T110/T130/T150

Voltage/Continuity Tester

Instruction Sheet

Introduction

The Fluke T90/T110/T130/T150 Electrical Testers (the

Tester or Product) are voltage and continuity testers

with a rotary eld indication (T110/T130/T150 only).

Their primary use is for test and measurement in

industrial, commercial, and household environments.

This Product complies with the most recent safety

standards for safe, reliable test and measurement.

The xed test probe cover prevents the risk of injury

when you move the instrument.

How to Contact Fluke

Fluke Corporation operates worldwide. For local

contact information, go to our website: www.uke.com

To register your product, view, print, or download

the latest manual or manual supplement, go to our

website.

Fluke Corporation

P.O. Box 9090

Everett, WA 98206-9090

+1-425-446-5500

uke-info@uke.com

Safety Information

 Warning

To prevent possible electrical shock, re, or

personal injury:

●Read all safety Information before you use the

Product.

● Use the Product only as specied, or the

protection supplied by the Product can be

compromised.

● Measure a known voltage rst to make sure

that the Product operates correctly.

●Do not apply more than the rated voltage,

between the terminals or between each

terminal and earth ground.

PN 3928132

October 2011, Rev. 3, 3/21

Specications are subject to change without notice. All product

names are trademarks of their respective companies.

● Limit operation to the specied measurement

category or voltage ratings.

●Do not work alone.

●Comply with local and national safety codes.

Use personal protective equipment (approved

rubber gloves, face protection, and ame-

resistant clothes) to prevent shock and arc

blast injury where hazardous live conductors

are exposed.

●Do not use the Product around explosive gas,

vapor, or in damp or wet environments.

●Do not use and disable the Product if it is

damaged.

●Do not use the Product if it operates

incorrectly.

● Keep ngers behind the nger guards on the

probes.

●Do not use the Product if the test leads are

damaged.

●Examine the case before you use the Product.

Look for cracks or missing plastic.

●The battery door must be closed and fastened

before you operate the Product.

●Replace the batteries when the low battery

indicator shows to prevent incorrect

measurements.

●Repair the Product before use if the battery

leaks.

●For use by competent persons. Anyone

using this Product should be knowledgeable

and trained about the risks involved with

measuring voltage, especially in an industrial

setting, and the importance of taking safety

precautions and of testing the Product before

and after using it to ensure that it is in good

working condition.

Symbols

These symbols are on the Tester or in this instruction

sheet.

Symbol Explanation

Important information. Consult the

instruction sheet.

Hazardous Voltage.

Suitable for live working.

Conforms to European Union Directives

CAT III Measurement Category III is applicable to

test and measuring circuits connected to

the distribution part of the building’s low-

voltage MAINS installation.

CAT IV Measurement Category IV is applicable

to test and measuring circuits connected

at the source of the building’s low-voltage

MAINS installation.

Symbol Explanation



This product complies with the WEEE

Directive (2002/96/EC) marking

requirements. The a󰀩xed label indicates

that you must not discard this electrical/

electronic product in domestic household

waste. Product Category: With reference

to the equipment types in the WEEE

Directive Annex I, this product is classed

as category 9 "Monitoring and Control

Instrumentation" product. Do not dispose

of this producat as unsorted municipal

wast. To to Fluke's website for recycling

information.

Accessories

The Tester is supplied with accessories.

Part Number Accessory

4083642 GS38 Probe Tip Sheath

4083656 4.2 mm Probe Extensions∅

4111533 H15 Belt Holster (sold separately)

4111540 C150 Zippered Soft Carrying Case

(sold separately)

Figure 1 shows the Probe Tip Protector Cap. This

multifunctional accessory is useful for tests and

storage of di󰀨erent accessories. (The Probe

Extensions are stored in the Probe Tip Protector Cap

before shipment.)

Storage area for Probe Tip Sheaths

Storage area for 4.2 mm Probe Extensions∅



Earth-pin safety-socket opener for UK

sockets (press opener into socket to release

safety covers, see Figure 2)

Storage area for probes when not in use

Quick Reference

Use the pushbuttons to turn the functions on or o󰀨.

See the list that follows for a quick reference to each

of these pushbuttons.

Pushbutton Description

Push to turn torch light on or o󰀨

(T110, T130, T150).

To save battery power the

function automatically turns o󰀨

after 30 seconds.

Push to hold the value that shows

in the LCD in volt and resistance

measurements. Push again to

turn HOLD o󰀨 (T130, T150).

To save battery power the

function automatically turns o󰀨

after 30 seconds.

Push this button on each of

the probes at the same time to

start the test for low impedance

switchable load.

Push and hold for 2 seconds to

turn the beeper on or o󰀨. The

status shows on the LCD (T150,

T130) or with the LED (T110).

Push and hold for 2 seconds to

turn the resistance measurement

on or o󰀨 (T150 only).

To save battery power, the

function automatically turns o󰀨

after 30 seconds.

Figure 3 illustrates how to store and retrieve the tip

accessories from the cap.

1/4

For storage, push Probe Tip Sheath into

place.

To retrieve, rmly push probe tip into Probe

Tip Sheath.

Pull on probe handle to remove Probe Tip

Sheath.

For storage, push 4.2 mm ∅ Probe

Extensions into place.

To retrieve, rmly push probe tip into Probe

Extensions. Twist 1/4 turn.

Pull on probe handle to remove Probe

Extensions. Continue to twist until tip is tight.

Features

Model

T90 T110 T130 T150

Complies with EN 61243-3:2014 • • • •

LED Indication Range: 12 V to 690 V dc and ac • • • •

V Display: Multiple LED Bargraph • • • •

Independent ELV indicator LED, indicates if >50 V ac/120 V dc is present even in

the event of no battery power or main circuit failure • • • •

LCD Indication Range: 6 V to 690 V dc and ac • •

V Display: Digital LCD 3½ digit (1 V resolution) • •

Resistance Measurement: LCD 3½ digit (0 to 1999 Ω/1Ω resolution) •

LCD Backlight • •

Display HOLD: Freeze/unfreeze display with voltage or resistance measurement • •

CAT II 690 V / CAT III 600 V •

CAT III 690 V / CAT IV 600 V •••

Rugged, Double-Insulated Wire • • • •

Fixed Impedance ~200 kΩ ( 3.5 mA @ 690 V)~• • • •

Switchable Load by 2 pushbuttons (30 mA @ 230 V) •••

Vibration During Load (when 2 switchable load pushbuttons are pushed) •••

Single-Pole Phase Test (also operates with gloves) • • • •

Rotary Field Direction (also operates with gloves) •••

Continuity Test / Diode Test • • • •

Torch •••

Beeper for Continuity/Phase/ACV (switchable) •••

Beeper for Continuity/Phase/ACV (nonswitchable) •

IP54 •

IP64 •••

Slim Metal Probe Tips (threaded base for included tip accessories) • • • •

Probe Tip Protector Cap (secure storage for the docked probes) • • • •

4.2 mm Probe Tip Thickness Extensions (for better t in outlets)∅ • • • •

19 mm Probe Tip distance when docked • • • •

Probe Tip Sheath (UK GS38 sheath–keeps the exposed metal to a <4 mm limit) • • • •

Slim Probe for Ultra-Compact Form Factor •

Display

LEDs

(All Models) Description

Voltage level is backlit

zVoltage level is more than ELV

limit (>50 V ac or >120 V dc)

aVoltage is ac / phase in Single

Pole Phase test

Voltage is positive or negative at

the indicator probe

bBattery is low / Replace battery

MSilent mode (T110)

fContinuity or diode in forward

operation

gSwitchable load is ON (two buttons

pressed and current ows)

q r 3-phase sequence indication

detected left or right turning

phases with nonindicator probe

(L1) to indicator probe (L2)

gpn06.eps

LCD

(T130/T150) Description

Silent mode (T130/T150)

Display is in HOLD mode

Voltage measurement (T130/T150)

or resistance measurement (T150)

Resistance measurement (T150)

AC Voltage measurement

DC Voltage measurement

Battery is low / Replace battery

How to Hold the Tester

Always hold the product behind the barrier to keep the

display in view. See Figure 4.

 Warning

To prevent possible electric shock, never

touch the metal pins of the probes when

power is applied.

Self‑Test

The Tester has a built-in self test function.

Before and after use, do a self-test:

1. Touch and hold the probe tips together.

f shows and you can hear the beeper (when

active on the T110/T130/T150). Or, in the

silent mode, the LED is on (when active on the

T110). This makes sure that the test leads have

continuity.

2. Make sure that:

• batteries are good

• b (T90, T110) is NOT on

• (T130, T150) does not show in the B

display

3. Continue to hold the probe tips together for more

than three seconds.

4. Open the probe tips again. All LEDs (all but z and

g) must be on and all symbols in the LCD (T130,

T150) show for one second. This test makes sure

that all other internal circuits and indicators are

good.

5. Measure a known voltage such as a 230 V socket

outlet. This completes the self-test and includes

the >ELV circuit.

If the Tester fails the self-test or voltage test, do not

use. See To Contact Fluke for service.

For an inspection of the insulation, cables, and case,

see Safety Information.

4 5

Produkt Specifikationer

Mærke:	Fluke
Kategori:	Ikke kategoriseret
Model:	T110
Bredde:	70 mm
Dybde:	38 mm
Højde:	260 mm
Vægt:	280 g
Batteritype:	AAA
Antal understøttede batterier:	2
Maksimal spænding:	- V
Husets farve:	Black, Grey, Red, Yellow
DC spændingsområde:	- V
AC-spæningsområde:	- V
AC strømområde:	- A