GE Café CHP9536SJSS Manual
Læs nedenfor 📖 manual på dansk for GE Café CHP9536SJSS (16 sider) i kategorien Komfur. Denne guide var nyttig for 20 personer og blev bedømt med 4.5 stjerner i gennemsnit af 10.5 brugere
Side 1/16
Installation
Instructions
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT — Save these instructions
for local inspector’s use.
• IMPORTANT — Observe all governing
codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions for
future reference.
• Product failure due to improper installation is not
covered under the Warranty.
WARNING This appliance must be properly
grounded.
• ATTENTION INSTALLER
— ALL COOKTOPS MUST BE HARD WIRED
(DIRECT WIRED) INTO AN APPROVED
JUNCTION BOX. A “PLUG AND RECEPTACLE” IS
NOT PERMITTED ON THESE PRODUCTS.
• Proper installation is the responsibility of the
installer and product failure due to improper
installation is NOT covered under warranty.
PARTS INCLUDED
MATERIALS YOU WILL NEED
TOOLS YOU MAY NEED
30 and 36”
Electric Cooktop - Induction
CUTTING THE COUNTERTOP
If you are installing the cooktop in a solid surface
material such as granite, quartz or any other natural
or synthetic solid surface, we recommend that the
cutout be prepared by a professional cabinet or
countertop installer.
Cooktop cutouts in wood or wood-laminate
countertops may be able to be prepared using a
saber saw and electric drill.
31-2000021 Rev. 2 11-18 GEA
Baffle
(For all installations
except over an oven)
2 Hex-Head Screws
Foam Tape
WB06K5042
2 Hold Down
Brackets
or order alternate
installation kit
WB01X24570
4 Phillips Screws
WB01X1137
Saber Saw
Pencil
Safety Glasses
1/8" Drill Bit & Electric or
Hand Drill
Ruler or Straightedge
Phillips Head
Screwdriver
1/4" Nut Driver
Large Size
Wire Nuts
Junction Box
(Sized for conduit per
local electrical codes.)
90º or Straight
Squeeze Connector
for 1” Conduit
Questions? Call us at 1.800.432.2737 or visit GEAppliances.com.
In Canada, call 1.800.561.3344 or visit GEAppliances.ca.
231-2000021 Rev. 2
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
FOR YOUR SAFETY
• For Personal Safety, remove house fuse or open
circuit breaker before beginning installation. Failure
to do so could result in serious injury or death.
• Be sure your cooktop is installed properly by a
qualified installer or service technician.
• To eliminate the risk of burns or fire due to reaching
over heated surface elements, cabinet storage
located above the surface units should be avoided.
If cabinet storage space is to be provided, the risk
can be reduced by installing a range hood that
projects horizontally a minimum of 5” beyond the
bottom of the cabinets. Cabinet installation above
the cooktop may be no deeper than 13”.
• Make sure the cabinets and wall coverings around
the cooktop can withstand the temperatures (up to
200°F) generated by the cooktop.
• The cooktop should be easy to reach and lighted
with natural light during the day.
• Always disconnect the electrical service to the
cooktop before repairing or servicing the cooktop.
This can be done by disconnecting the fuse or
circuit breaker. Failure to do this could result in a
dangerous or fatal shock. Know where your main
disconnect switch is located. If you do not know,
have your electrician show you.
ELECTRICAL REQUIREMENTS
This appliance must be supplied with the proper
voltage and frequency, and connected to an
individual, properly grounded branch circuit, protected
by a circuit breaker or a time delay fuse as noted on
name plate and on the chart below.
Use the chart below to determine the minimum
recommended dedicated circuit protection:
KW Rating
240V
KW Rating
208V
Recommended
Circuit Size
(Dedicated)
.: .: 20 Amp
4.9 KW–7.2 KW 4.2 KW–6.2 KW 30 Amp
7.3 KW–9.6 KW 6.3 KW–8.3 KW 40 Amp
9.7 KW–12.0 KW 8.4 KW–10.4 KW 50 Amp
We recommend you have the electrical wiring and
hookup of your cooktop connected by a qualified
electrician. After installation, have the electrician show
you where your main cooktop disconnect is located.
Wiring must conform to National Electrical Code and
all local electrical codes. You can get a copy of the
National Electrical Code, ANSI/NFPA No. 70-Latest
Edition, by writing to:
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
In Canada, wiring must conform to Canadian Electrical
Code (CEC).
The cooktop conduit wiring is approved for copper
wire connection only, and if you have aluminum house
wiring, you must use special UL approved connectors
for joining copper to aluminum. In Canada, you must
use special CSA approved connectors for joining
copper to aluminum.
You must use a two-wire, three conductor 208/240
VAC, 60 Hertz electrical system. A white (neutral)
wire is not needed for this unit. The cooktop must be
installed in a circuit that does not exceed 125 VAC
nominal to ground.
Refer to the name plate on your cooktop for the KW
rating for your cooktop.
These cooktops
require 40 amp
service for 30” units,
50 amp service for
36” units.
Name plate location
Produkt Specifikationer
| Mærke: | GE |
| Kategori: | Komfur |
| Model: | Café CHP9536SJSS |
Har du brug for hjælp?
Hvis du har brug for hjælp til GE Café CHP9536SJSS stil et spørgsmål nedenfor, og andre brugere vil svare dig
Komfur GE Manualer
17 Januar 2025
24 December 2024
16 August 2024
6 August 2024
26 Juli 2024
27 Maj 2024
26 Maj 2024
23 Maj 2024
21 Maj 2024
17 Maj 2024
Komfur Manualer
- Komfur Nova
- Komfur Duro
- Komfur Kabola
- Komfur Tectro
- Komfur Midea
- Komfur Cuckoo
- Komfur Classique
- Komfur Heinner
- Komfur Kunft
- Komfur Salter
- Komfur Elvita
- Komfur Olsberg
- Komfur Elro
- Komfur Mellerware
- Komfur Altech
Nyeste Komfur Manualer
2 Juni 2025
2 Juni 2025
2 Juni 2025
1 Juni 2025
1 Juni 2025
1 Juni 2025
1 Juni 2025
1 Juni 2025
1 Juni 2025
1 Juni 2025