GE GFWS2605FRR Manual

GE Vaskemaskine GFWS2605FRR

Læs gratis den danske manual til GE GFWS2605FRR (2 sider) i kategorien Vaskemaskine. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om GE GFWS2605FRR, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Once the washer is within 4 feet

of its destination, use a 1/2"

wrench or socket to remove

the following from the back side:

• 4 shipping bolts

• 4 plastic spacers

(including rubber grommets)

• 4 power cord retainers

Insert the hole caps in the bolt holes once

the shipping bolts and spacers have been

removed. Save all bolts and spacers for future use.

Recycle or destroy the carton after the washer is unpacked.

This quick reference guide is provided for informational purposes only and does not replace, modify or change in any manner the Owner’s Manual & Installation Instructions.View videos on installation steps at www.geappliances.com/videos-media/

For your safety

• To reduce the risk of re, electric shock, or injury to persons when using or installing

the product, read and obey all safety information provided in the Owner’s Manual &

Installation Instructions that accompanied the product.

• Do not install or store appliance in an area where it will be exposed to dripping water or

outside weather conditions. See Location of Your Washer section in the Owner’s Manual

& Installation Instructions.

• NOTE: This appliance must be properly grounded and installed as described in these

steps and the Owner’s Manual & Installation Instructions. Electrical service to the

washer must conform with local codes and ordinances and the latest edition of the

national Electrical Code, ANSI/NFPA 70.

Run water from both faucets to ﬂush the lines and

remove particles that might clog the water valve screens.

Ensure that a rubber washer is in the end of the hot

and cold hoses.

Connect the inlet hoses to the hot "H" outlet and

cold "C" outlet.

Hand-tighten and then tighten them another

2/3 turn with pliers.

Do not crossthread or over-tighten these connections.

Ensure that a screen washer is inserted into the faucet

end of both hoses with protruded side facing the

faucet. If a rubber washer is already inserted,

remove before inserting screen washer.

Connect the inlet hose from the "H" outlet

to the hot faucet and the inlet hose from

the "C" outlet to the cold faucet.

Hand-tighten and then tighten them

another 2/3 turn with pliers.

Turn on the water and check for leaks.

Connect hoses

to water supply

Connect hoses

to washer

Unpack

your washer

quick installation guide

Remove

shipping hardware Video

Attach U-shaped hose guide

to end of drain hose.

Place hose in laundry tub or

standpipe and secure with cable tie.

If placed in standpipe, the end of

the drain hose should extend only

4 to 7 inches down the pipe.

Plug washer into a grounded

outlet. Do not use an extension

cord or adaptor plug.

Main power is turned on.

The washer is plugged in.

Faucets are turned on.

Water hoses are connected securely with no leaks at both ends.

Unit is level and all legs are on the ﬂoor.

Shipping bolts and spacers are removed and stored for future use.

Drain hose is placed in tub or standpipe and secured with a cable tie.

Run a load of clothes in the SPEED WASH cycle.

Check for leaks.

When the load is spinning at high speed, ensure that the washer

and leveling legs are stable.

If necessary, pause the cycle and adjust the front leveling legs until the washer

is properly level. Restart the cycle in order to allow it to finish.

7 8

Final installation

checklist Test cycle

Install drain hose

and plug

Parts supplied Parts required Tools needed

Cable tie

Hose

guide

Adjustable wrench

or 1/2" socket with ratchet

Channel-lock

adjustable pliers

Adjustable wrench

or 14 mm and

16 mm wrench

Carpenter’s level

Scan this code

to watch a video

on Step 2.

Gently rock the washer into nal location,

ensuring inlet hoses do not become kinked.

Do not use door or dispenser drawer to

lift the washer.

Place level on top.

Loosen nut then adjust the front leveling

legs up or down using a 14 mm or

adjustable wrench.

Level washer both side-to-side

and front-to-back.

Level

your washer

Video

Scan this code

to watch a video

on Step 5.

Instructions en Français - Voir le Manuel du propriétaire • Instrucciones en Español - Ver el Manual de instrucciones

DO NOT DISCARD. RETAIN FOR FUTURE USE.

STOP

WARNING

Hand tighten nuts toward the base of the washer and

tighten with a 16 mm wrench until a minimum of 3 clicks.

GE recommends inlet hoses that have a 90 degree bend at one end. The

90 degree bend should be installed at the washer as shown above.

Use and care

manual

Water Hoses (2)

Screen washers (2)

Extend leg Shorten leg

Produkt Specifikationer

Mærke:	GE
Kategori:	Vaskemaskine
Model:	GFWS2605FRR

Har du brug for hjælp?

Hvis du har brug for hjælp til GE GFWS2605FRR stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vaskemaskine GE Manualer

GE GFW350SPY Manual

4 November 2025

GE Profile PDD415PYYFS Manual

9 September 2025

GE PDT705SYWFS Manual

26 August 2025

GE PFW955SPWGN Manual

21 August 2025

GE PFW870SSVWW Manual

7 August 2025

GE PFW870SPVRS Manual

7 August 2025

GE GTW538ASWWS Manual

7 August 2025

GE PDP755SYVFS Manual

7 August 2025

GE GFWR4800FWW Manual

28 Juli 2025

GE GTWN4950FWW Manual

28 Juli 2025

Vaskemaskine Manualer

Nyeste Vaskemaskine Manualer

Hoover HBP 410BL8G-80 Manual

5 November 2025

Milectric LV-SN58DWC Manual

5 November 2025

BEKO HTE10736XS Manual

5 November 2025

Infiniton WM-F94AWM Manual

5 November 2025

Infiniton WM-F84AWH Manual

5 November 2025

Infiniton WM-F124AWX Manual

5 November 2025

Milectric LV-SN60DWC Manual

5 November 2025

Electrolux WB6-50 Manual

4 November 2025

Electrolux WN6-35 Manual

4 November 2025

Electrolux EUD-618CV Manual

3 November 2025