GE Profile JD966TDWW Manual

GE Komfur Profile JD966TDWW

Læs gratis den danske manual til GE Profile JD966TDWW (16 sider) i kategorien Komfur. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 5 anmeldelser. Har du et spørgsmål om GE Profile JD966TDWW, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/16
CAUTION: Before you begin
Read these instructions carefully and
completely
• IMPORTANT-Save these instructions for
local inspector’s use.
• IMPORTANT-Observe all governing codes
and ordinances.
GE Self Cleaning Radiant
Electric Drop-In Range
Installation
Instructions JDP46,JD966
• NOTE TO INSTALLER- Be sure to leave
these instructions with the consumer.
• OWNER- Keep these instructions for future
reference.
• WARNING- This appliance must be
properly grounded. See “Electrical
Requirements” page 2.
Tools You Will Need
Pub. No. 31-10427
229C4053P413 1
“If you have questions, call 800-GE-CARES or visit our website at:
www.GEAppliances.com”
Nut driver
Pencil
Hand or
Saber Saw
Straight Edge
or Square
Level
Tape
Measure
Materials Needed
Wire Nuts
Parts Supplied
Safety Glasses
Skill Level: Average High Low
Completion Time: 1 to 3 Hours
Proper installation is the responsibility of the installer. Product failure due to improper installation
is not covered under the GE Appliance Warranty. See the Owners Manual for warranty
information.
1
2
3
4
Phillips
Screwdriver
(Not smaller than #8
gage combined with
house wiring gage.)
(See warning Page
6 if house wiring is
aluminum.)
STD
Screw
Driver
Junction Box
(If not included in
house wiring)
4- 11/16” x 4- 11/16” x 2- 1/4” Sq.
Min. (See N.E.C. for space require-
ments)
Hammer
Lower Trim
2 Screws
Power Drill
& 1/8” Bit
2 Shoulder
screws (for stop
device)
All rough-in and spacing dimensions must be met
for safe use of your range.
To reduce the risk of burns or fire when reaching
over hot surface elements, cabinet storage space
above the cooktop should be avoided. If cabinet
storage space is to be provided above the cooktop,
the risk can be reduced by installing a range hood
that sticks out at least 5” beyond the front of the
cabinets. Cabinets installed above a cooktop must
be no deeper than 13”.
Be sure your appliance is properly installed and
grounded by a qualified technician.
For Your Safety
2
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of
tipping the appliance must be
secured by installing the range so
that the anti-tip bracket (attached to the
rear of the range) correctly engages under
the counter top or properly affixed portion
of the wall or cabinet.
If you pull the range out and away from the
countertop opening for any reason, make sure
the Anti-Tip bracket is engaged when the range
is pushed back against the opening.
This appliance must be supplied with the proper
voltage and frequency, and connected to an
individual properly grounded branch circuit,
protected by a circuit breaker or fuse having
amperage as specified on the appliance rating
plate. (Rating Plate is located behind the oven
door on the range.)
We recommend you have the electrical wiring
and hookup of your range connected by a
qualified electrician. After installation, have the
electrician show you where your main range
disconnect is located.
Check with your electric utility for electrical codes
which apply in your area. Failure to wire your
oven according to governing codes could result in
a hazardous condition. If there are no local
codes, your range must be wired and fused to
meet the requirements of the National Electrical
Code, ANSI/NFPA No. 70-Latest Edition. You can
get a copy by writing:
National Fire Protection Association
Battery March Park
Quincy, MA 02269
Effective January 1, 1996, the National Electrical
Code requires that new, but not existing,
construction utilize a 4 conductor connection to
an electric range. When installing an electric
range in new construction, follow the instructions
in the section on NEW CONSTRUCTION AND
FOUR CONDUCTOR BRANCH CIRCUIT
CONNECTION.
You must use a three-wire, single-phase A.C.
208Y/120 Volt or 240/120 Volt, 60 hertz electrical
system. If you connect to aluminum wiring,
properly installed connectors approved for use
with aluminum wiring must be used.
Electrical Requirements
WARNING: For personal safety
remove house fuse or open circuit
breaker before beginning installation.
Failure to do so could result in serious
injury or even death.
WARNING
• All ranges can tip
• Injury to persons could result
• Install anti-tip bracket
• See Installation Instructions

Produkt Specifikationer

Mærke: GE
Kategori: Komfur
Model: Profile JD966TDWW

Har du brug for hjælp?

Hvis du har brug for hjælp til GE Profile JD966TDWW stil et spørgsmål nedenfor, og andre brugere vil svare dig


Komfur GE Manualer

GE

GE UX12B30PSS Manual

13 August 2025
GE

GE Profile PLS624ETSB Manual

7 August 2025
GE

GE Profile PLU621ETSB Manual

7 August 2025
GE

GE Profile PLU612DTBB Manual

7 August 2025
GE

GE JP3030SWSS Manual

7 August 2025
GE

GE JGB720DEJWW Manual

7 August 2025
GE

GE JP3030TWWW Manual

7 August 2025
GE

GE GGS60LAVFS Manual

7 August 2025
GE

GE JXPROBE1 Manual

7 August 2025
GE

GE Café CXPR6HKPTBT Manual

7 August 2025

Komfur Manualer

Nyeste Komfur Manualer

Hisense

Hisense GM643XHC Manual

15 August 2025
Candy

Candy CLE64XE Manual

14 August 2025
Candy

Candy CI64248CTT Manual

14 August 2025
Candy

Candy CVG6PX LPG Manual

14 August 2025
Candy

Candy CHG953WX LPG Manual

14 August 2025
Candy

Candy CVG9B LPG Manual

14 August 2025
Candy

Candy CH95CE Manual

14 August 2025
Philips

Philips HD4412 Manual

14 August 2025
Candy

Candy CGG95HXLPG/1 Manual

14 August 2025
Candy

Candy CI642CMBB Manual

14 August 2025