GE Profile JP961SHSS Manual

GE Komfur Profile JP961SHSS

Læs gratis den danske manual til GE Profile JP961SHSS (8 sider) i kategorien Komfur. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om GE Profile JP961SHSS, eller vil du spørge andre brugere om produktet?

Side 1/8
36" Electric Cooktop
Installation
Instructions JP960, JP961, JP968, JP969, ZEU769
CAUTION: Before you begin—read these
instructions completely and carefully.
IMPORTANT—Save these instructions for
local inspector’s use.
IMPORTANT—OBSERVE ALL GOVERNING
CODES AND ORDINANCES.
Note to Installer—Be sure to leave these
instructions with the Consumer.
Note to Consumer—Keep these instructions
for future reference.
Note—This appliance must be properly
grounded.
Parts Included
1/8" Drill Bit &
Electric or
Hand Drill
Phillips
Head
Screwdriver
Pencil Ruler or
Straightedge
Wire Nuts
Saber Saw
2 Foam Strips
4 Screws
Tools You Will Need
1
2 Hold
Down
Brackets
Junction
Box
“If you have questions, call 800.GE.CARES or visit our website at:
www.GEAppliances.com
Materials Needed
229C4053P530
31-10546 (09-02 JR)
ATTENTION INSTALLER: ALL COOKTOPS
MUST BE HARD WIRED (DIRECT WIRED)
INTO AN APPROVED JUNCTION BOX.
A “PLUG AND RECEPTACLE” IS NOT
PERMITTED ON THESE PRODUCTS.
For Personal Safety, remove house fuse
or open circuit breaker before beginning
installation. Failure to do so could result
in serious injury or death.
Be sure your cooktop is installed properly
by a qualified installer or service technician.
To eliminate the risk of burns or fire due
to reaching over heated surface elements,
cabinet storage located above the surface
units should be avoided. If cabinet storage
space is to be provided, the risk can be
reduced by installing a range hood that
projects horizontally a minimum of 5"
beyond the bottom of the cabinets. Cabinet
installation above the cooktop may be no
deeper than 13."
Make sure the cabinets and wall coverings
around the cooktop can withstand the
temperatures (up to 200°F) generated
by the cooktop.
The cooktop should be easy to reach and
lighted with natural light during the day.
Always disconnect the electrical service to
the cooktop before repairing or servicing
the cooktop. This can be done by
disconnecting the fuse or circuit breaker.
Failure to do this could result in a
dangerous or fatal shock. Know where your
main disconnect switch is located. If you do
not know, have your electrician show you.
2
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
This appliance must be supplied with
the proper voltage and frequency, and
connected to an individual, properly
grounded branch circuit, protected by a
circuit breaker or a time delay fuse as
noted on rating plate.
We recommend you have the electrical
wiring and hookup of your cooktop
connected by a qualified electrician. After
installation, have the electrician show you
where your main cooktop disconnect
is located.
Wiring must conform to National Electrical
Code. You can get a copy of the National
Electrical Code, ANSI/NFPA No. 70-Latest
Edition, by writing:
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
The cooktop conduit wiring is approved for
copper wire connection only. If you have
aluminum house wiring, you must use
special UL approved connectors for joining
copper to aluminum.
You must use a two-wire, three conductor
208/240 VAC, 60 Hertz electrical system.
A white (neutral) wire is not needed for this
unit. The cooktop must be installed in a
circuit that does not exceed 125 VAC
nominal to ground.
Refer to the rating plate on your cooktop
for the KW rating for your cooktop.
Electrical
Requirements
For Your Safety


Produkt Specifikationer

Mærke: GE
Kategori: Komfur
Model: Profile JP961SHSS

Har du brug for hjælp?

Hvis du har brug for hjælp til GE Profile JP961SHSS stil et spørgsmål nedenfor, og andre brugere vil svare dig