Genelec 8351AWM Manual

Genelec Højttaler 8351AWM

Læs gratis den danske manual til Genelec 8351AWM (12 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Genelec 8351AWM, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/12

8260A, 8351A, 8250A and 8240A

Operating Manual

Introduction

Congratulations and a thank-you for the purchase of this Genel-

ec SAM system. All Genelec SAM systems are designed to in-

tegrate easily into the digital production environment. There are

several ways to configure and operate SAM systems for a wide

variety of high quality audio applications. The SAM monitors

also have analog inputs, making them versatile and intelligent

replacements for standard analog monitors.

This manual addresses the setup and use of the 8240A, 8250A,

8351A and 8260A SAM monitors in stand-alone mode without

the Genelec Loudspeaker Manager GLM™ and the proprietary

Genelec monitor control network. Use with the GLM™ is de-

scribed in the GLM™ System Operating Manual.

System

Genelec 8240A, 8250A, 8351A and 8260A are designed for

precise monitoring of 24 bit/192 kHz AES/EBU digital audio sig-

nal or line level analog audio signal. They are fully compatible

with Genelec Loudspeaker Manager GLM™ and the proprietary

Genelec monitor control network, and Genelec 7260A, 7270A

and 7271A SAM Subwoofers, but can also be used indepen-

dently of these. The 8240A, 8250A, 8351A and 8260A feature

high SPL output, low colouration and broad bandwidth in a small

enclosure size. They are suitable for a wide variety of tasks,

such as near field monitoring, mobile vans, broadcast and TV

control rooms, multichannel sound systems and home studios.

The Minimum Diffraction Enclosure™ (MDE™), advanced Di-

rectivity Control Waveguide™ (DCW™) and Minimum Diffrac-

tion Coaxial (MDC™) technologies provide excellent frequency

balance even in difficult acoustic environments.

Amplifiers

The amplifier unit is mounted in the rear of the monitor enclosure.

The unit incorporates special circuitry for driver thermal overload

protection. Variable input sensitivity allows accurate level match-

ing to console output section.

Setting Up the GLM™ Control Network

Although the

8240A, 8250A, 8351A and 8260A can be used

without the GLM

™ software and control network, they only reach

their full potential when set up and calibrated using the GLM™

software. The setup is fast and consists of the following steps:

1. Run a CAT5 (RJ45) cable from the monitor control network

to the next monitor (see Figure 1).

2. Run the final cable to control network input of the GLM

Adapter device.

3. Connect the GLM Adapter device to your computer USB

connector. The cable

is a part of the GLM User Kit

4. Place the Genelec measurement microphone at the listen-

ing location of the engineer, on a stand, with the microphone

pointing upwards and the microphone top at the height of the

engineers ear in normal working position. The microphone is

a part of the GLM User Kit.

5. Run the microphone cable to the microphone input in the

GLM Adapter device.

6. Download GLM software at the Genelec web site (www.

genelec.com). Install the GLM software.

7. Follow the GLM software instructions to measure and set

up your monitors.

8. If you plan to not use a computer for controlling the moni-

tors, use the GLM software to write the setting into the moni-

tors (“Store the Settings”).

Using the Monitors in Stand-Alone Mode

When the monitors are not connected to a Genelec monitor con-

trol network, they operate in the stand-alone mode. However, set-

tings made with the Genelec Loudspeaker Manager software can

be saved into each monitor and applied even when the network

is disconnected by setting switch 1 “STORED/MANUAL CON-

TROL” on switch group 2 of each monitor to position “STORED.”

All issues concerning use with the network are explained in detail

in the System Operating Manual provided with the GLM™ Loud-

speaker Manager software kit.

Connections

Each monitor is supplied with a mains cable, one 5 m GLM net-

work cable and an operating manual. Before connecting up, en-

sure that the mains switch is off.

LISTENING

POSITION

MICROPHONE

GLM

NETWORK

GLM

NETWORK

GLM

NETWORK

USB

Figure 1. GLM control network cabling

Produkt Specifikationer

Mærke:	Genelec
Kategori:	Højttaler
Model:	8351AWM
Bredde:	287 mm
Dybde:	278 mm
Højde:	452 mm
Vægt:	19000 g
Brugervejledning:	Ja
Produktfarve:	Hvid
Udgangseffekt (RMS):	270 W
Anbefalet brug:	Studio
Frekvensområde:	32 - 35000 Hz
Forbindelsesteknologi:	Ledningsført
Lyd-output kanaler:	1.0 kanaler
Højttaler, placering:	Floor,Tabletop/bookshelf
Antal drivere:	1
Diskanthøjttaler:	Ja
Sensitivitet:	111 dB
Diskant diameter:	0.75 "
Bashøjttaler:	Ja
Woofer diameter:	215 mm
Forstærker:	Indbygget
Mid-range driver diameter:	101 mm
Woofer diameter (britisk mål):	8.5 "
XLR indgang:	Ja
Mid-range driver diameter (britisk mål):	4 "