Hama 00093733 Manual

Hama Ikke kategoriseret 00093733

Læs gratis den danske manual til Hama 00093733 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Hama 00093733, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

III

GOperating instruction

Thank you for choosing a Hama product.

Take your time and ad the following instructions and informa-re

tion completely. Please keep these instructions in a safe place

for future ference.re

1. Explanation of rning mbols and NotesWa Sy

Warning

This symbol is used to indicate safety instructions or to draw

your attention to specic hazards and risks.

Note

This symbol is used to indicate additional information or

important notes.

2. Safety Notes

•Use the product for its intended purpose only.

•Protect the product from dirt, moisture and overheating, and

only use it in a dry environment.

•When using this product, observe the applicable local trac

laws and gulations.re

•Do not drop the product and do not expose it to any major

shocks.

•Keep the packaging material out of the ach of children duere

to the risk of suffocation.

•Dispose of packaging material immediately according to

locally applicable gulations.re

•Do not modify the product in any way. Doing so voids the

warranty.

3. Montage

Note

•Before mounting the holder, check the installation options

in your vehicle. If in doubt, consult the manual for your

vehicle or contact the manufacturer.

•Never apply force when using the product or during

installation.

Warning

•Take care that components such as airbags, safety areas,

controls, instruments, etc. and visibility are not blocked or

restricted.

•Do not allow yourself to be distracted by the product,

for example when driving a vehicle or operating sports

equipment. Always pay attention to the surrounding trac

and your environment.

Pictures for illustration only!

The use of the product you’ve purchased may differ slightly.

If you have diculties installing or questions about the product,

please call our support line (see

5. Service und Support

3.1 taching the holder (I)At

Ventilation grille clamp (A)

•Carefully push the ventilation grille clamp onto the open

panels of the ventilation grille until it locks into place.

Note

Before setting a device in the holder, check that the panels

are sturdy enough to bear the weight. commend againstWe re

using this model for terminal devices heavier than 300 g.

•To remove the holder, use a suitable tool (such as a screw-

driver) to gently press the locking pin downwards and then

carefully pull the holder out of the ventilation grille.

Screw-fastening (B)

Note

Make sure that there are no cables or pipes underneath the

selected installation site that might be damaged.

•Use suitable screws to fasten the holder to the selected

installation site.

Adhesive pad (C)

Note – Installation surface

Please note that the selected installation surface (e.g.

dashboard) should be free of dust and grease. Use a suitable

cleaning agent from a specialised dealer to clean the surface.

•(Remove one of the protective lms from the adhesive pad and

press it onto the ar side of the holder for a few seconds.)re

•Remove the (other) protective lm from the adhesive pad and

gently press the holder onto the selected installation surface.

Note

•Wait at least 24 hours after installing the adhesive pad

before attaching the holder.

•Note that the adhesive pad is permanently attached. To

remove the adhesive pad, carefully pull it off the installation

surface. The adhesive pad can only be attached again using

suitable adhesive material available from specialised dealers.

•Various environmental factors such as ambient humidity,

sunlight or cold can impair the durability of the adhesive pad.

•We recannot guarantee that sidue will not be left on the

mounting surface after the adhesive pad is moved.re

Handlebar clamp (D)

Note

Make sure that the installation will not sult in any controlre

elements, cables, instruments, etc. being covered up,

pinched, or impaired in their functioning.

•Use a suitable tool (optionally included), loosen the screws to

open the clamp and attach it to the handlebar.

•If necessary, use rubber pads or adapters (optionally included)

to adjust the clamp to t the diameter of the handlebar.

•Close the clamp and fasten it in place by tightening the screws.

Suction cup holder (E)

•Remove the protective lm from the suction cup and position

it on a clean and at surface (e.g. window pane).

•If the suction cup holder is to be attached to a ugh or une-ro

ven surface (e.g. a dashboard), an adapter plate is optionally

available.

•Push the locking lever (E – 1) to fasten the suction cup.

•Open the clamping device (E – 4) to position the carrying arm.

•Close the clamping device to lock this position.

•To release the suction cup from the surface, pull the lateral

slides in the direction of the arrow. (E – 2) Then gently pull the

ap to completely lease the suction cup. (E – 3)re

3.2 Mounting the holder (II)

Clip system (A) / 4-hook/hole clip system (B)

•Set the cess or cesses of the holder onto the bracket.re re

•Move the holder up or down until it clicks into place or is

seated rmly.

4-hook/hole clip system – QuickFIX (C)

•Press the buttons on the side of the bracket together. Then set

the cesses on the ar of the holder onto the hooks of there re

bracket. Let go of the buttons to engage the mounting clip

and fasten the holder in place.

•To remove the holder, press the buttons on the side of the

bracket together. The clip system disengages and you can

remove the holder.

3.3 Inserting and moving terminal devices (III)re

Note

•Always take your terminal device out of the holder before

attaching or moving the bracket (adhesive pad, suctionre

cup holder, ventilation grille clamp or other).

•If using a handlebar clamp (I-D), use only a (universal)

attachment system that additionally secures the terminal

device from falling or protects it from sulting damagere

(such as prods. no. 88404, 88415, 91324, 93710).

Suitable attachment systems for handlebar mounting are,

for instance, protective bags, brackets with elastic straps,

etc. (such as prods. no. 93830, 93778)

Universal bracket A

•Press the button on the side of the universal bracket to open

the taining jaws. (A – 1)re

•Insert the terminal device of your choice and secure it in place

by lightly pushing the taining jaws together. (A – 2)re

•Also adjust the lower carrying arms to the terminal device by

pulling them further apart or pushing them closer together.

(A – 3)

•In order to easily move the terminal device, press the buttonre

on the side of the universal holder. (A – 1)

Universal bracket B

•Turn the small wheel in the direction indicated by the arrow/

anti-clockwise to open the taining jaws. (B – 1)re

•Insert the terminal device of your choice and secure it in place

by lightly pushing the taining jaws together. (B – 2)re

•Adjust both the height and the depth of the taining jawre

xtures to your terminal device by pulling them further apart

or pushing them closer together. (B – 2)

•Also adjust the lower carrying arms to the terminal device by

pulling them further apart or pushing them closer together.

(B – 3)

•Remove the bottom/top covering cap to add or move carry-re

ing arms. Replace the covering cap once the adjustments to t

your terminal device have been made. (B – 4)

Note

When using the universal bracket, use as many adjustable

mountings as are necessary for the terminal device to be

perfectly seated. prevent the device from falling out, pushTo

the taining jaws securely together.re

4. rranty DisclaimerWa

Hama GmbH & Co. assumes no liability and provides no war-KG

ra renty for damage sulting from improper installation/mounting,

improper use of the product or from failure to observe the

operating instructions and/or safety notes.

5. Service and Support

Please contact Hama Product Consulting if you have any ques-

tions about this product.

Hotline: +49 9091 502-115 (German/English)

Further support information can be found here: www.hama.com

All s eli arested brands trademark of th correspond ie om onsing compan s. Errors and issi

exce alpted ec, dan subj t to technic changes. rOu gener delal terms of ivery d tan paymen

are applied.

Hama GmbH & Co KG

86652 Monheim/ Germany

www.hama.com

000884000030/11.15

Produkt Specifikationer

Mærke:	Hama
Kategori:	Ikke kategoriseret
Model:	00093733
Type:	Passiv
Vægt:	23 g
Produktfarve:	Sort
Antal:	1
Materiale:	Plast
Drejelig:	Ja
Kapabilitet:	Garmin Nuvi 2 Series
Mærke kompatibilitet:	Garmin
Beslagtype til enhed:	Klemmebeslag