Harman Kardon Adapt+ Manual

Harman Kardon Højttaler Adapt+

Læs nedenfor 📖 manual på dansk for Harman Kardon Adapt+ (38 sider) i kategorien Højttaler. Denne guide var nyttig for 29 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/38

OWNER’S MANUAL

EN/

WI R E L E S S A UDI O S Y S T E M

OMNI BAR+

OMNI ADAPT+

SAFE T Y

INS TRUC TIONS

Verify Line Voltage Before Use

The Omni Bar+ and Omni Adapt+ have been designed for use with 100-240 volt, 50/60 Hz AC current.

Connection to a line voltage other than that for which your product is intended can create a safety

and fire hazard and may damage the unit. If you have any questions about the voltage requirements

for your specific model, or about the line voltage in your area, contact your selling dealer before

plugging the unit in to a wall outlet.

Do Not Use Extension Cords

To avoid safety hazards, use only the power cord supplied with your unit. We do not recommend

that extension cords be used with this product. As with all electrical devices, do not run power cords

under rugs or carpets, or place heavy objects on them. Damaged power cords should be replaced

immediately by an authorized service center with a cord that meets factory specifications.

Handle the AC Power Cord Gently

When disconnecting the power cord from an AC outlet, always pull the plug; never pull the cord.

If you do not intend to use your speaker for any considerable length of time, disconnect the plug

from the AC outlet.

Do Not Open the Cabinet

There are no user-serviceable components inside this product. Opening the cabinet may present

a shock hazard, and any modification to the product will void your warranty. If water accidentally

falls inside the unit, disconnect it from the AC power source immediately, and consult an authorized

service center.

S A F E T Y I N S T R U C T I O N S

O W N E R ’ S M A N U A L

Safety Instructions 2

Introduction 5

Unpacking 6

Buttons and Connectors 9

Link Button 13

Source Button 13

Bluetooth Button 13

Play/Pause Button 13

Volume +/- Buttons 14

Surround Button 14

Power Button 14

HDMI TV, AUX-in, and Optical Buttons 14

Mute Button 14

Subwoofer Volume Control 14

Stereo and Virtual Buttons 14

Battery Door Unlock Button 14

WPS Button 15

Reset Button 15

Power Connector 15

Audio In Connector 15

Optical In Connector 15

HDMI TV Connector 15

IR Transmitter Connector 15

Pairing Button 16

Optical Out Connector 16

Audio Out Connector 16

Subwoofer Out Connector 16

Crossover Adjustment 16

TABLE OF CONTENTS

Speaker Setup 17

Connecting Your Speaker to Wi-Fi 18

iOS 19

Android 20

WPS 20

WPS-PBC 20

WPS-PIN 21

Wireless 5.1 Surround Setup 21

Source Setup 22

Connecting Your Speaker to Bluetooth 22

Connecting External Sources 23

Controlling Your Speaker 24

Speakers, Rooms, and Groups 24

Volume and Muting 25

Switching Sources 25

Remote Control 25

Playing Music from Wi-Fi 26

Harman Kardon Controller App 26

Spotify Connect 27

Chromecast built-in 28

Upgrading 29

Troubleshooting 31

Problem & Solution 31

Open Source Declarations 33

Technical Specifications - Omni Bar+ 34

Technical Specifications - Omni Adapt+ 36

INTRODUC TION

Congratulations on your Harman Kardon Omni Bar+ or Harman Kardon Omni Adapt+ (sold separately)

purchase! Harman has for long been a leader in driving new technologies that enable and enhance our

customers’ audio experiences, a tradition we continue to uphold with this product line. We’ve created

a system that harnesses the power and versatility of your home wireless network to create a better

and easier audio experience without compromising on audio quality. We hope you enjoy your new

Harman Kardon Wireless HD Music System product and that you’ll consider extending our solution

throughout your home.

By using your home wireless network you will enjoy a far greater physical range of use than with a

conventional Bluetooth® connection.

You will also be able to use your product in various combinations throughout your household and

control them from either the product or from the Harman Kardon Controller app.

To obtain maximum enjoyment from your product, please read this manual and refer back to it as you

become more familiar with its features and their operation.

If you have any questions about these products, their installation or their operation, please contact your

Harman Kardon retailer or custom installer, or visit the website at www.harmankardon.com/wireless.

I N T R O D U C T I O N

U N PAC K I N G

What’s in the box

Omni Bar+

U N P A C K I N G

x 1

x 1 : 1.0 m

x 1 : 1.2 m

x 2 : 1.2 m

x 1 : 1.45 m

x 1

x 2

x 1

U N P A C K I N G

x 1

x 1 : 1.5 m

x 1

x 1 : 0.8 m

Omni Adapt+

U N P A C K I N G

B U T T O N S A N D C O N N E C T O R S

BUT TONS AND

CONNEC TORS

Buttons - Omni Bar+

Buttons - Remote

SOURCE

PLAY/PAUSE

SURROUND

VOLUME - VOLUME +

LINKBLUETOOTH

RESET

PAIRING

VOLUME

BASS

STEREO BATTE RY

LOCK

HDM I TV AUX IN OPTICAL

VIRTUAL

WPS

1) WPS button

2) Reset

3) USB port (software update only)

4) AUX input (analog audio in)

5) IR transmitter

6) Power input DC

7) Pairing

8) HDMI TV

9) Optical (digital optical audio in)

1) Power

2) HDMI TV,Aux in,Optical

3) Bluetooth®

4) Link

5) Play/pause

6) Volume control +/-

7) Mute

8) Subwoofer volume control +/-

9) Stereo, Virtual

10) Battery Lock

B U T T O N S A N D C O N N E C T O R S

B U T TO NS A N D

CO N N E C TO R S

Buttons - Subwoofer

Buttons - Adapt+

Crossover adjustment

Wireless pairing button

Reset button

Wireless pairing indicator

Phase adjustment

RESET

SOURCE PLAY/PAUSE

LINK

Optical

Out

Optical

Ethernet

RESET WPS

B U T TO NS A N D

CO N N E C TO R S

Connectors - Omni Bar+

Connectors - Subwoofer

B U T T O N S A N D C O N N E C T O R S

AUDIO IN

AC POWER CORD

SERVICE PORT (Don't use it for charging)

IR REPEATER

AC POWER CORD

SUBWOOFER PAIRING

RESET

B U T TO NS A N D

CO N N E C TO R S

Connectors - Adapt+

B U T T O N S A N D C O N N E C T O R S

Optical

Out

Optical

Ethernet

Link Button

Pressing the Link button adds this speaker to a different speaker group. Grouped speakers all play

the same music. For example, if you are listening to music in the Bedroom, you can walk to the

Kitchen and press the Link button on the speaker in the Kitchen. The Kitchen will join and begin to

play the same music as the Bedroom. Pressing multiple times will switch between different groups

on the network.

Pressing the Link button for 5 seconds will enable Party Mode, which sends the same music to every

speaker in the house.

Source Button

Pressing the Source button cycles the currently active music source in this room between AUX-in,

Optical, and HDMI TV for the Omni Bar+ or AUX-in, Optical, and Bluetooth for the Omni Adapt+. If

you are currently streaming audio over Wi-Fi, it will switch away from Wi-Fi to one of these other

sources. Switching to one of these sources will send the same music that you hear on this speaker

to all the other speakers in the same group. On the Omni Bar+, this button will light up white when

the active source is HDMI TV, green when the active source is AUX-in, or amber when the active

source is Optical.

Bluetooth Button

Press the Bluetooth Button to enter Bluetooth pairing mode on the Omni Bar. This button will also

switch the currently active source to Bluetooth. Note that on the Omni Adapt+, you must press the

Source button for 3 seconds to enter Bluetooth pairing mode instead.

Play/Pause Button

The Play/Pause button pauses or resumes music playback on Bluetooth or any of the Wi-Fi sources,

including Spotify Connect and Chromecast built-in. AUX-in audio must be paused from the external

audio source.

BUT TONS AND

CONNEC TORS

B U T T O N S A N D C O N N E C T O R S

Volume +/- Buttons

Press the Volume + button to increase volume, or press the Volume – button to decrease volume.

Pressing both at the same time will mute the speaker.

Surround Button

The Surround button on the Omni Bar+ will turn on Virtual Surround. If Virtual Surround is already on,

it will instead turn it off. When Virtual Surround is on, this button will light up amber. When turned

off, it will light up white.

Power Button

This button will put the Omni Bar+ into Standby mode. If it’s already in Standby mode, then the Omni

Bar+ will turn on instead. Note that both the Omni Bar+ and Omni Adapt+ will automatically enter

Standby mode after 10 minutes of inactivity.

HDMI TV, AUX-in, and Optical Buttons

Pressing these buttons will switch the Omni Bar+ to the corresponding input source.

Mute Button

Press this button to mute the Omni Bar+. Pressing again will unmute and return to the previous

volume level.

Subwoofer Volume Control

Press the Bass + Button to adjust the level of the Omni Bar+ subwoofer up, or press the Bass - Button

to decrease the level of the subwoofer.

Stereo and Virtual Buttons

Press the Stereo button to turn off Virtual Surround on the Omni Bar+. Press the Virtual Button to

turn Virtual Surround on.

Battery Door Unlock Button

This button on the Omni Bar+ remote control is used to remove the battery door on the back of the

remote control. When you wish to replace the Omni Bar+ remote control battery, press and hold

this button down while sliding the battery cover off. The remote control uses as standard CR2025

3V battery.

WPS Button

This button is used to connect the speaker to your home Wi-Fi network. Press it to enter WPS PBC mode.

Press it for 5 seconds to enter WPS PIN mode. See the WPS section on page 20 for more information.

Reset Button

Press the Reset button for 5 seconds to perform a factory reset. This will erase all user settings,

disconnect from the Wi-Fi network, and the speaker will enter Wi-Fi setup mode, allowing you to

connect it to a different Wi-Fi network.

Power Connector

Use the supplied power supply or power cord to connect the speaker to AC power.

Audio In Connector

Connect an analog audio source via a 3.5mm or 1/8” stereo AUX cable to this connector to enjoy

audio from an analog audio device.

Optical In Connector

Use an optical audio cable to connect your Omni Bar+ or Omni Adapt+ to your TV or external audio

source. This connector supports 2.0 channel PCM up to 96KHz, 24-bit or Dolby Digital signals.

Note: If you use an optical connection to your TV, change your TV audio settings to support “external

speakers” and disable the built-in TV speakers.

HDMI TV Connector

If your TV supports HDMI ARC, you can hear the TV audio through your Omni Bar+ using a single

HDMI cable connected to the HDMI TV input connector. This connector supports 2.0 channel PCM

up to 96KHz, 24-bit or Dolby Digital signals.

IR Transmitter Connector

If your Omni Bar+ blocks the IR remote control for your TV, you can connected the included IR

transmitter to this connector. Place the other end of the IR transmitter close to your TV, and you will

again be able to use your TV remote control.

B U T T O N S A N D C O N N E C T O R S

Pairing Button

Your Omni Bar+ comes from the factory already paired with the wireless subwoofer. If you ever need

to reconfigure or replace your Omni Bar+ or wireless subwoofer, you can connect them again by

pressing this button on both the Omni Bar+ and the wireless subwoofer. The LEDs will begin flashing

quickly, and after 30 seconds the connection will be complete.

Optical Out Connector

Connect the Omni Adapt+ to a receiver or amplifier using an optical cable for the highest quality

digital audio connection.

Audio Out Connector

Connect speakers or an amplifier here via a 3.5mm stereo cable if your external device doesn’t

support optical audio.

Subwoofer Out Connector

Connect an active subwoofer to the Omni Adapt+ using an RCA audio cable.

Crossover Adjustment

Use this to adjust the crossover frequency of the Omni Bar+ subwoofer. If the bass seems too loud

or boomy, you can adjust this toward the Min setting. If you want more bass, you can adjust toward

the Max setting.

B U T T O N S A N D C O N N E C T O R S

In this section you will set up your Omni Bar+ or Omni Adapt+, connecting it to Wi-Fi and connecting

each source device you plan to use.

Before you begin, download the Harman Kardon Controller app for iOS or Android. This app is

available on both the iOS App Store and the Google Play Store. You will use this app to set up and

configure the speaker.

If you prefer to learn via video, Harman Kardon has created a helpful setup video. Just scan the QR

code below to be taken to the video on the web.

Setup video

SPEAKER SE TUP

S P E A K E R S E T U P

https://www.youtube.com/watch?v=34k46uA4vhs

https://www.youtube.com/watch?v=ztfVLWjNFTU

https://www.youtube.com/watch?v=Cfp26N8PXvc

https://www.youtube.com/watch?v=2-Um9WH1zX0

https://www.youtube.com/watch?v=In_7bxCtALM

https://www.youtube.com/watch?v=JvQlg0Zxt84

English: Spanish:

Italian:

French:

Norwegian:

Dutch:

Produkt Specifikationer

Mærke:	Harman Kardon
Kategori:	Højttaler
Model:	Adapt+

Har du brug for hjælp?

Hvis du har brug for hjælp til Harman Kardon Adapt+ stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler Harman Kardon Manualer

Harman Kardon Luna Manual

30 December 2025

Harman Kardon HKB4 Manual

26 December 2024

Harman Kardon Champagne Manual

26 December 2024

Harman Kardon HKTW6 Manual

26 December 2024

Harman Kardon Citation ONE DUO MKIII Manual

26 December 2024

Harman Kardon HKTS 18 Manual

25 December 2024

Harman Kardon HKS 3 Manual

25 December 2024

Harman Kardon HKTS 12 Manual

20 December 2024

Harman Kardon HKTS 6 Manual

20 December 2024

Harman Kardon HKS 2 Manual

20 December 2024

Højttaler Manualer

Nyeste Højttaler Manualer

Klipsch Synergy KSF-C5 Manual

10 April 2025

Klipsch Synergy KSF-S5 Manual

10 April 2025

Panasonic SC-BMAX10 Manual

9 April 2025

Audiofrog GB40 Manual

8 April 2025

JBL Stage 250 Manual

7 April 2025

JBL Conceal C62 Manual

7 April 2025

JBL Conceal C83 Manual

7 April 2025

Grundig Jam 2 Manual

6 April 2025

Elipson W35 Manual

5 April 2025

Turbosound Manchester MC15-RS Manual

4 April 2025