Hikvision DS-PDSMK-4BAR Manual

Hikvision Alarmsystem DS-PDSMK-4BAR

Læs gratis den danske manual til Hikvision DS-PDSMK-4BAR (2 sider) i kategorien Alarmsystem. Denne vejledning er vurderet som hjælpsom af 41 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 21 anmeldelser. Har du et spørgsmål om Hikvision DS-PDSMK-4BAR, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Photoelectric Smoke Detector

Installation Wiring Diagram

TYPICAL WIRING DIAGRAM

Figure 1 shows the typical wiring diagram of the 4-wire

multiple-station smoke detector system.

FIRST DETECTOR BASE LAST DETECTOR BASE

POWER

DETECTOR

EN54 LISTED

COMPATIBLE

CONTROL

PANEL

INITIATING

LOOP

CLASS A OPTIONAL WIRING

Fig. 1B Installing the 4-wire multiple station smoke detector base

EOL

POWER

SUPERVISION

RELAY

MODULE

END

LINE

DEVICE

5 2

6 1 3 4

DO NOT PLACE LINKS BETWEEN THE WIRING POSITIONS

OF TERMINALS 2 AND 5 TO PROVIDE POWER

SUPERVISION

WARNING

TO PREVENT DETECTOR CONTAMINATION AND

SUBSEQUENT WARRANTY CANCELLATION, THE

SMOKE DETECTOR MUST REMAIN COVERED UNTIL

THE AREA IS CLEAN AND DUST FREE.

INSTALLING THE BASE

1. To insure proper installation of the detector head to the

base, all the wires should be properly addressed at

installation:

(A) Position all the wires at against terminals.

(B) Fasten the wires away from connector terminals.

2. If you use a jumper wire to connect the poles of

terminal 2 and 5 when testing the detector loop

continuity, be sure to remove the jumper wire prior to

the installation of the detector head.

3. The end- -line device shown in g. 1(a) and 1(b) of

should be compatible with the control unit. The

end of- -line supervisory relay used should be rated for

the DC power voltage used.

4. As per EN 54 standard, open area smoke detectors

are intended for mounting on a ceiling no less than

100mm from a wall or mounting on a wall than no less

than 100mm and no more than 300mm from a ceiling.

5. The base of the smoke detector can be mounted

directly onto an electrical junction box such as an

octagonal (75mm, 90mm or 100mm), a round (75mm),

or a square (100mm) box without using any type of

mechanical adapter.

INSTALLING THE HEAD

1. Align the components as shown in Figure 2.

2. Mate the detector head onto the base and twist

clockwise to secure it.

3. Do not install the detector head until the area is

thoroughly cleaned of construction debris, dusts, etc.

The maximum number of smoke detector installed in

the same loop is 30 units.

B A S E

DET E C TO R H E ADLE DR E C TANG U LA R

OP EN I NG H E R E

LON G A LI G N M EN T M A R K

Fig. 2 Mating detector head onto base

ADJUSTMENT THE RELAY POSITION

ADJUSTING THE RELAY FOR NO/NC

The normal condition for the relay is normally open “ ”

(NO).

1. To adjust the normal condition of the relay to

“ ”normally closed (NC), insert a screwdriver into the

rectangular hole located on the side between the front

cover and base and rotate to remove the front cover.

2. Refer to gure 3. There is a jumper head next to the

relay on the PCB. Remove the jumper head and reinsert

it in the NC position.

3. Carefully replace the front cover.

Relay contact Jumper

rating: setting

1A@30VDC,

0.5A@125VAC.

TESTING

1. All the alarm signal services, releasing device and

extinguisher system should be disengaged during the

test period and must be re-engaged immediately at the

conclusion of testing.

2. After energizing the detector head for approximately

one minute, check to see the indicator green LED

ashing once every 4~6 seconds. If green LED fails to

ash, it indicates the non-functioning of the detector or

faulty wiring. Re-check the wiring or replace the

detector if necessary.

3 Allow smoke from a cotton wick or a test smoke .

aerosol to enter the detector-sensing chamber for at

least 10 seconds. When sucient smoke has entered

the chamber, the detector will signal an alarm, this

being visible by a continuous illumination of the LED.

Reset each detector and/or control unit before

attempting to test any additional detectors in the same

zone. If the alarm fails in this step, it indicates a

defective unit, which requires service.

RELAY

CHAMBER

LED

Fig. 3 Schematic of detector structure

When front cover is open.

Produkt Specifikationer

Mærke:	Hikvision
Kategori:	Alarmsystem
Model:	DS-PDSMK-4BAR

Har du brug for hjælp?

Hvis du har brug for hjælp til Hikvision DS-PDSMK-4BAR stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Alarmsystem Hikvision Manualer

Hikvision DS-PD201MC-WB Manual

30 September 2025

Hikvision DS-PM2-D Manual

28 Juli 2025

Hikvision DS-PDCO-E-WE Manual

27 Juli 2025

Hikvision DS-PDHT-E-WE Manual

27 Juli 2025

Hikvision DS-PDSMK-E-WE Manual

27 Juli 2025

Hikvision DS-PD201P10-WB Manual

6 Juli 2025

Hikvision DS-PK201B-WB Manual

6 Juli 2025

Hikvision DS-PS201-WE Manual

6 Juli 2025

Hikvision DS-PKF201-WE Manual

18 December 2024

Hikvision DS-PS110-WE Manual

2 September 2024

Alarmsystem Manualer

Nyeste Alarmsystem Manualer

Dahua Technology HY-GC20B-R8 Manual

1 November 2025

Abus Smartvest Pro FUMK45000 Manual

29 Oktober 2025

B.E.G. PD11-KNXs-FLAT-ST Manual

8 Oktober 2025

Evolveo Alarmex Pro Manual

18 September 2025

Kemo M062 Manual

18 September 2025

Velleman K8093 Manual

17 September 2025

Smartwares FGA-13091 Manual

16 September 2025

Brandson 304339 Manual

15 September 2025

Kidde SM120X Manual

14 September 2025

Elektrobock ELBO-073 Manual

14 September 2025