HK Audio PP-CP Manual


Læs gratis den danske manual til HK Audio PP-CP (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 16 anmeldelser. Har du et spørgsmål om HK Audio PP-CP, eller vil du spørge andre brugere om produktet?

Side 1/4
Single
Head-Stack Head-Stack Cluster
Cluster
PP/CP Set Art. No. 1007525
2x Pick Point / 2x Cluster Plate
for LINEAR 5 LTS / LTS A
LINEAR 5 MK II 308 LTA
Installation Instructions / Montageanleitung 1.1
Please read these instructions before
installation and keep them for later
reference.
Heads up: Be sure to observe all the
applicable regulations for installation to
ceilings, walls and trusses.
Bitte vor Gebrauch lesen und für
späteren Gebrauch aufbewahren!
Wichtig! Die geltenden Vorschriften für
die Montage an Decken, Wänden oder
Trägern sind unbedingt zu beachten.
CP Art. no. 6000227
PP Art. no. 6000226
30° Cluster Single
30° Cluster Single
30° ClusterSingle
30° Cluster
Single
Made in Germany
Single
1 2 3
Head-Stack
1
4
2
5
3
6
1. Place the cabinet face down on a stable base before mounting
any hardware.
2. Use a 5 mm hex key or the proper bit on a cordless screwdriver
to remove the two countersunk M8 screws from the bottom and
top panels.
3. Attach the cluster plate to the bottom and the pick-point to the
top of the cabinet by inserting these M8 countersink screws into
the holes and tightening them down (refer to the cover sheet).
1. Vor Montage die Box mit der Vorderseite auf einen sicheren
Untergrund legen.
2. Auf Unter- und Oberseite die beiden M8-Senk schrauben mittels
5 mm-Innensechskant-Schlüssel oder Schrauberbit heraus-
drehen.
3. Auf der Unterseite der Box die Clusterplatte und auf der Obersei-
te den Pick-Point mit den zuvor ent fernten M8-Senkschrauben
befestigen (s. Deckblatt).
1. Set the bottom cabinet on a stable base.
2. Turn the upper cabinet on its head and place it top side
down on the lower cabinet.
3. Use a 5 mm hex key or the proper bit on a cordless
screwdriver to remove the thumbscrews (four per side)
along with the washers from the countersunk panels
on each side. Then use the LTS slide rails to connect the
cabinets, fastening them down on both sides with two
thumbscrews and two washers each.
4. Attach the pick-point and cluster plate, following steps
1 to 3 in the instructions for a single cabinet.
You now have two and three anchor points, respectively,
for flying a single cabinet or head stack.
1. Die untere Box auf einen sicheren Untergrund stellen
2. Die obere Box um 180° gedreht mit dem Deckel auf die
untere Box stellen
3. In den seitlichen Fräsungen die Rändelschrauben
(4 Stück je Seite) samt Unterlegscheiben mittels
5mm-Innensechskant-Schlüssel oder Schrauberbit
herausdrehen. Die Boxen mittels der LTS-Schiebebleche
auf beiden Seiten mit je 2 Rändelschrauben und 2
Unterlegescheiben fest verbinden. Die restlichen
Rändelschrauben und Unterlegscheiben in den freien
Gewinden verschrauben.
4. Pick-Point und Clusterplatte montieren (siehe Single:
Punkt 1 bis 3)
Für die Single- bzw. Headstack-Anwendung stehen
nun zwei, respektive drei Anschlagpunkte für den
Flugbetrieb zur Verfügung.


Produkt Specifikationer

Mærke: HK Audio
Kategori: Ikke kategoriseret
Model: PP-CP

Har du brug for hjælp?

Hvis du har brug for hjælp til HK Audio PP-CP stil et spørgsmål nedenfor, og andre brugere vil svare dig