Hotpoint H7F HP43 X UK Manual

Hotpoint Opvaskemaskine H7F HP43 X UK

Læs gratis den danske manual til Hotpoint H7F HP43 X UK (8 sider) i kategorien Opvaskemaskine. Denne vejledning er vurderet som hjælpsom af 40 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 20.5 anmeldelser. Har du et spørgsmål om Hotpoint H7F HP43 X UK, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
1
ENDaily Reference Guide
THANK YOU FOR BUYING A HOTPOINT PRODUCT.
In order to receive a more complete assistance, please
register your appliance on: www.hotpoint.eu/register
CONTROL PANEL
1. ON-OFF/Reset button with indicator light
2. PREVIOUS program button
3. NEXT program button
4. FAVOURITE program button with indicator light
5. Salt reservoir empty indicator light
6. Rinse Aid reservoir empty indicator light
7. DESCALE indicator light
8. Closed Water tap indicator light
9. Key lock indicator light
10. Program number remaining time and indicator
11. Display
12. Zone Wash 3D Option button with indicator light
FIRST TIME USE
SETTING MENU
1. Switch on the appliance by pressing the button.ON-OFF
2. Hold the Settings (Half Load ) button for 3 seconds, until you hear
a beep and the display shows „SEt”.
3. After one second therst available setting (letter „h”) will be displayed.
4. Press PREVIOUS /NEXT to scroll through the list of available settings
(see table below), then press START/Pause to view and change the
value of the currently selected setting.
5. Press PREVIOUS /NEXT to change the value, then press START/Pause
to save the new value and return to the main menu.
6. To change another setting, repeat points 4 and 5.
7. Press or wait 30 seconds to exit the menu.ON-OFF
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on
the machine’s functional components.
The salt reservoir is located in the lower part of the dishwasher (under the
lower rack on the left side).
• It is mandatory that the salt reservoir never be empty.
• It is important to set the water hardness.
• Salt must belled when the SALT REFILL indicator light on the control
panel is lit. 1. Remove the lower rack and unscrew the reservoir cap
(anticlockwise).
2. Position the funnel and ll the salt reservoir (see gure)
right up to its edge (approximately kg); it is not un0,5 -
usual for a little water to leak out.
3. Only the rst time you do this: ll the salt reservoir
with water.
4. Remove the funnel and wipe any salt residue away from the opening.
Make sure the cap is screwed on tightly so that no detergent can get into
the container during the wash program (this could damage the water
softener beyond repair).
Run a program every time as soon as you completed relling the salt
reservoir to avoid corrosion.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential that the water
hardness setting is based on the actual water hardness in your house. This infor-
mation can be obtained from your local water supplier. The factory setting is “3”.
See „WATER HARDNESS TABLE”.
LETTER SETTING VALUES
(Default - )in bold
Water Hardness Level
(see “SETTING THE WATER HARDNESS”
and “WATER HARDNESS TABLE”) 1 | 2 | | 4 | 53
Rinse Aid Level
(see “ADJUSTING THE DOSAGE OF RINSE AID”) 0 | 1 | 2 | 3 | 4 | 5
ActiveDry (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O 1 | 0
Sound
“1” = On, “0” = O 1 | 0
Factory Settings
Press START/Pause to restore to the factory
default all the values of the settings included
in the settings menu.
-
Water Hardness Table
Level °dH
German degrees
°fH
French degrees
°Clark
English degrees
1 (Soft) 0 - 6 0 - 10 0 - 7
2 (Medium) 7 - 11 11 - 20 8 - 14
3 (Average) 12 - 16 21 - 29 15 - 20
4 (Hard) 17 - 34 30 - 60 21 - 42
5 (Very hard) 35 - 50 61 - 90 43 - 62
To change, follow instructions in section “SETTING MENU”.
Only use salt that has been specically designed for dishwashers.
After the salt has been poured into the machine, the SALT REFILL indicator
light switches o.
If the salt container is not lled, the water softener and the heating
element may be damaged as a result of limescale accumulation.
Use of salt is recommended with any type of dishwasher detergent.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently preventing
scale buildup on the heater, contributing also to better cleaning eciency.
This system regenerates itself with salt, therefore it is required to rell
the salt container when empty. The frequency of regeneration depends
on the water hardness level setting - regeneration takes place once per 4-6
Eco cycles with the water hardness level set to 3. The regeneration process
occurs at the beginning of the cycle with additional fresh water.
• Single regeneration consumes ~3L of water;
• Takes up to 5 additional minutes for the cycle;
• Consumes below 0.005kWh of energy.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser should be A
lled when the RINSE AID REFILL indicator light in the control panel is lit.
1. Open the dispenser B by
pressing and pulling up the
tab on the lid.
2. Pour in the rinse aid (max.110
ml), making sure it does not
overow from the dispenser.
If this happens, clean the spill
immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can adjust
the quantity of rinse aid used.
To change, follow instructions in the section “SETTING MENU”.
If the rinse aid level is set to ZERO, no rinse aid will be supplied. The LOW
RINSE AID indicator light will not be lit if you run out of rinse aid.
A maximum of levels can be set according to the dishwasher model. 6
• If you see bluish streaks on the dishes, set a low number (0-3).
• If there are drops of water or limescale marks on the dishes, set
a mid-range number (4-5).
FILLING THE DETERGENT DISPENSER
To open the detergent dispenser use the opening device C. Introduce
the detergent into the dry dispenser D only. Place the amount of
detergent for pre-washing directly inside the tub.
1. When measuring out the detergent refer to the
mentioned earlier information to add the proper
quantity. Inside the dispenser , there are indicaD-
tions to help the detergent dosing.
2. Remove detergent residues from the edges of the
dispenser and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling
it up until the closing device is secured in place.
The detergent dispenser automatically opens up at
the right time according to the program.
Usage of detergent not designed for dishwashers may cause
malfunction or damage to the appliance.
A
B
D
C
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
13. Half Load Option button with indicator light/ - 3 sec. pressSettings
14. Extra Dry Keylock Option button with indicator light/ - 3 sec. press
15. Delay Option button with indicator light
16. START/Pause button with indicator light
Before using the appliance carefully read Safety
and Installation Instructions. More information about your product
available on website: docs.whirlpool.eu
After installation, please remember to remove all transport protection
parts from the dishwasher.

Produkt Specifikationer

Mærke: Hotpoint
Kategori: Opvaskemaskine
Model: H7F HP43 X UK

Har du brug for hjælp?

Hvis du har brug for hjælp til Hotpoint H7F HP43 X UK stil et spørgsmål nedenfor, og andre brugere vil svare dig


Opvaskemaskine Hotpoint Manualer

Hotpoint

Hotpoint HA2FFC14BX Manual

8 Oktober 2025
Hotpoint

Hotpoint HA2FFD14BX Manual

8 Oktober 2025
Hotpoint

Hotpoint HI 3010 Manual

2 August 2025
Hotpoint

Hotpoint HSIO 3O23 WFE dishwasher Manual

2 August 2025
Hotpoint

Hotpoint HIC 3O33 WLEG Manual

1 August 2025
Hotpoint

Hotpoint HFC 2B19 X Manual

1 August 2025
Hotpoint

Hotpoint HIC 3C41 CW Manual

1 August 2025
Hotpoint

Hotpoint HFC 3C32 WX Manual

1 August 2025
Hotpoint

Hotpoint HIC 3C34 Manual

1 August 2025
Hotpoint

Hotpoint HSIC 3T127 C Manual

1 August 2025

Opvaskemaskine Manualer

Nyeste Opvaskemaskine Manualer

Whirlpool

Whirlpool WH6UC14BN7A0X Manual

1 November 2025
Big Chill

Big Chill BC24DWCBBMB Manual

31 Oktober 2025
Big Chill

Big Chill BC24DWRCAR Manual

31 Oktober 2025
Bauknecht

Bauknecht BKO IBM Manual

31 Oktober 2025
Big Chill

Big Chill BC24DWCCRPB Manual

31 Oktober 2025
Artusi

Artusi ADW5001 Manual

31 Oktober 2025
Big Chill

Big Chill BC24DWCSNCW Manual

31 Oktober 2025
Elektra Bregenz

Elektra Bregenz MGIV 56580 XL Manual

31 Oktober 2025
Siemens

Siemens SR93EX25MG Manual

31 Oktober 2025
Tornado

Tornado TDV-FN128COX Manual

31 Oktober 2025