Hotpoint HDA2000VBB Manual

Hotpoint Vaskemaskine HDA2000VBB

Læs gratis den danske manual til Hotpoint HDA2000VBB (32 sider) i kategorien Vaskemaskine. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Hotpoint HDA2000VBB, eller vil du spørge andre brugere om produktet?

Side 1/32
GE Consumer & Industrial
Appliances
Installation Instructions
Built-In Dishwasher
If you have questions, call 800.GE.CARES (800.432.2737) or visit our website at: GEAppliances.com
IMPORTANT The dishwasher MUST be
installed to allow for future removal from the
enclosure if service is required.
If you received a damaged dishwasher, you should
immediately contact your dealer or builder.
Optional Accessories – See the Owner’s Manual for
available custom panel kits.
FOR YOUR SAFETY
Read and observe all CAUTIONS and WARNINGS
shown throughout these instructions. While
performing installations described in this booklet,
gloves and safety glasses should be worn.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
IMPORTANT Observe all governing codes
and ordinances.
Note to InstallerBe sure to leave these
instructions for the consumer and local inspector’s
use.
Note to ConsumerKeep these instructions with
your Owner’s Manual for future reference.
Skill Level – Installation of this dishwasher requires
basic mechanical, electrical and plumbing skills.
Proper installation is the responsibility of
the installer. Product failure due to improper
installation is not covered under the GE
Appliance Warranty. See warranty information.
Completion Time – 1 to 3 Hours. New installations
require more time than replacement installations.
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
206C1559P195 31-30255 07-09 JR
In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca
TOOLS YOU WILL NEED:
Safety glasses
1/4" and 5/16" nutdrivers
Flashlight
Gloves
Adjustable wrench (6”)
Phillips-head screwdriver
Measuring tape
Level
Carpenter’s square
Bucket to catch water when flushing
water line
Tubing cutter
15/16" socket wrench
FOR NEW INSTALLATIONS:
Hole saw set
Drill and appropriate bits
PARTS SUPPLIED IN INSTALLATION
PACKAGE:
Two 8-18 x 5/8" Phillips-head wood screws
Junction box cover and #10 hex head
screw
Drain hose (78" long) and hose clamp
Cord protector (Power Cord Models Only)
Conversion leads (Power Cord Models Only)
Literature, product samples and/or
coupons
MATERIALS YOU WILL NEED:
WX09X70910 power cord if applicable to
your installation
UL-Listed wire nuts (3)
Thread seal tape
90° elbow, ferrule and compression nut –
(3/8" NPT external thread on one end and
opposite end sized to fit water supply)
GPF65 Side-mount bracket kit for use with
granite countertops
FOR NEW INSTALLATIONS:
Electrical cable
Water line3/8" minimum copper tubing
Strain relief for electrical connection
Hand shut-off valve (recommended)
Air gap for drain hose, if required
Waste tee for house plumbing, if
applicable
GPF10S drain hose (10' long), if needed
Screw-type hose clamps
Hose Clamp
78" Drain Hose
90° Elbow, Ferrule and
Compression Nut
Thread
Seal Tape
3 Wire Nuts Hot Water Line–3/8"
Minimum Copper
Tubing
Electrical Cable
or WR09X70910
Power Cord
Air
Gap Screw-Type
Hose Clamps
Strain Relief
Phillips-Head
Screwdriver
Level Carpenter’s
Square
Measuring Tape
Safety Glasses Flashlight
Gloves
Hole Saw Set
Drill and
Bits
Shut-Off
Valve
1/4" and 5/16" Nutdrivers
Adjustable
Wrench
Tubing
Cutter
GPF65 Side-Mount
Bracket Kit
#8
Phillips-Head
Wood Screws
5/8" long
Screw Kit
#10
Hex Head
Junction Box Screw
1/2" long Junction Box Cover
2
Cord Protector
(Power Cord Models Only)
Conversion Leads
(Power Cord Models Only)
15/16"
Socket Wrench
Bucket
Optional 10'
Drain Hose
GPF10S
Waste Tee


Produkt Specifikationer

Mærke: Hotpoint
Kategori: Vaskemaskine
Model: HDA2000VBB

Har du brug for hjælp?

Hvis du har brug for hjælp til Hotpoint HDA2000VBB stil et spørgsmål nedenfor, og andre brugere vil svare dig